1 /** 2 ****************************************************************************** 3 * @file stm32f1xx_hal_conf.h 4 * @author MCD Application Team 5 * @brief HAL configuration template file. 6 * This file should be copied to the application folder and renamed 7 * to stm32f1xx_hal_conf.h. 8 ****************************************************************************** 9 * @attention 10 * 11 * Copyright (c) 2017 STMicroelectronics. 12 * All rights reserved. 13 * 14 * This software is licensed under terms that can be found in the LICENSE file 15 * in the root directory of this software component. 16 * If no LICENSE file comes with this software, it is provided AS-IS. 17 * 18 ****************************************************************************** 19 */ 20 21 /* Define to prevent recursive inclusion -------------------------------------*/ 22 #ifndef __STM32F1xx_HAL_CONF_H 23 #define __STM32F1xx_HAL_CONF_H 24 25 #ifdef __cplusplus 26 extern "C" { 27 #endif 28 29 /* Exported types ------------------------------------------------------------*/ 30 /* Exported constants --------------------------------------------------------*/ 31 32 /* ########################## Module Selection ############################## */ 33 /** 34 * @brief This is the list of modules to be used in the HAL driver 35 * 36 * Note: 37 * HAL_I2C_MODULE_ENABLED had to be disabled due to the HAL 38 * redefining I2C_SPEED_STANDARD and I2C_SPEED_FAST when the 39 * I2C LL driver was enabled. 40 * 41 */ 42 #define HAL_MODULE_ENABLED 43 #define HAL_ADC_MODULE_ENABLED 44 #define HAL_CAN_MODULE_ENABLED 45 /* #define HAL_CAN_LEGACY_MODULE_ENABLED */ 46 #define HAL_CEC_MODULE_ENABLED 47 #define HAL_CORTEX_MODULE_ENABLED 48 #define HAL_CRC_MODULE_ENABLED 49 #define HAL_DAC_MODULE_ENABLED 50 #define HAL_DMA_MODULE_ENABLED 51 #define HAL_ETH_MODULE_ENABLED 52 #define HAL_EXTI_MODULE_ENABLED 53 #define HAL_FLASH_MODULE_ENABLED 54 #define HAL_GPIO_MODULE_ENABLED 55 #define HAL_HCD_MODULE_ENABLED 56 /* #define HAL_I2C_MODULE_ENABLED */ 57 #define HAL_I2S_MODULE_ENABLED 58 #define HAL_IRDA_MODULE_ENABLED 59 #define HAL_IWDG_MODULE_ENABLED 60 #define HAL_NAND_MODULE_ENABLED 61 #define HAL_NOR_MODULE_ENABLED 62 #define HAL_PCCARD_MODULE_ENABLED 63 #define HAL_PCD_MODULE_ENABLED 64 #define HAL_PWR_MODULE_ENABLED 65 #define HAL_RCC_MODULE_ENABLED 66 #define HAL_RTC_MODULE_ENABLED 67 #define HAL_SD_MODULE_ENABLED 68 #define HAL_SMARTCARD_MODULE_ENABLED 69 #define HAL_SPI_MODULE_ENABLED 70 #define HAL_SRAM_MODULE_ENABLED 71 #define HAL_TIM_MODULE_ENABLED 72 #define HAL_UART_MODULE_ENABLED 73 #define HAL_USART_MODULE_ENABLED 74 #define HAL_WWDG_MODULE_ENABLED 75 #define HAL_MMC_MODULE_ENABLED 76 77 /* ########################## Oscillator Values adaptation ####################*/ 78 /** 79 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 80 * This value is used by the RCC HAL module to compute the system frequency 81 * (when HSE is used as system clock source, directly or through the PLL). 82 */ 83 #if !defined (HSE_VALUE) 84 #if defined(USE_STM3210C_EVAL) 85 #define HSE_VALUE 25000000U /*!< Value of the External oscillator in Hz */ 86 #else 87 #define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */ 88 #endif 89 #endif /* HSE_VALUE */ 90 91 #if !defined (HSE_STARTUP_TIMEOUT) 92 #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ 93 #endif /* HSE_STARTUP_TIMEOUT */ 94 95 /** 96 * @brief Internal High Speed oscillator (HSI) value. 97 * This value is used by the RCC HAL module to compute the system frequency 98 * (when HSI is used as system clock source, directly or through the PLL). 99 */ 100 #if !defined (HSI_VALUE) 101 #define HSI_VALUE 8000000U /*!< Value of the Internal oscillator in Hz */ 102 #endif /* HSI_VALUE */ 103 104 /** 105 * @brief Internal Low Speed oscillator (LSI) value. 106 */ 107 #if !defined (LSI_VALUE) 108 #define LSI_VALUE 40000U /*!< LSI Typical Value in Hz */ 109 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz 110 The real value may vary depending on the variations 111 in voltage and temperature. */ 112 /** 113 * @brief External Low Speed oscillator (LSE) value. 114 * This value is used by the UART, RTC HAL module to compute the system frequency 115 */ 116 #if !defined (LSE_VALUE) 117 #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */ 118 #endif /* LSE_VALUE */ 119 120 #if !defined (LSE_STARTUP_TIMEOUT) 121 #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ 122 #endif /* LSE_STARTUP_TIMEOUT */ 123 124 /* Tip: To avoid modifying this file each time you need to use different HSE, 125 === you can define the HSE value in your toolchain compiler preprocessor. */ 126 127 /* ########################### System Configuration ######################### */ 128 /** 129 * @brief This is the HAL system configuration section 130 */ 131 #define VDD_VALUE 3300U /*!< Value of VDD in mv */ 132 #define TICK_INT_PRIORITY 0x0FU /*!< tick interrupt priority */ 133 #define USE_RTOS 0U 134 #define PREFETCH_ENABLE 1U 135 136 #define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ 137 #define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ 138 #define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ 139 #define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ 140 #define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ 141 #define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ 142 #define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ 143 #define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ 144 #define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ 145 #define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ 146 #define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ 147 #define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ 148 #define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ 149 #define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ 150 #define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ 151 #define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ 152 #define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ 153 #define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ 154 #define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ 155 #define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ 156 #define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ 157 #define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ 158 #define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ 159 160 /* ########################## Assert Selection ############################## */ 161 /** 162 * @brief Uncomment the line below to expanse the "assert_param" macro in the 163 * HAL drivers code 164 */ 165 /* #define USE_FULL_ASSERT 1U */ 166 167 /* ################## Ethernet peripheral configuration ##################### */ 168 169 /* Section 1 : Ethernet peripheral configuration */ 170 171 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ 172 #define MAC_ADDR0 2U 173 #define MAC_ADDR1 0U 174 #define MAC_ADDR2 0U 175 #define MAC_ADDR3 0U 176 #define MAC_ADDR4 0U 177 #define MAC_ADDR5 0U 178 179 /* Definition of the Ethernet driver buffers size and count */ 180 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ 181 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ 182 #define ETH_RXBUFNB 8U /* 8 Rx buffers of size ETH_RX_BUF_SIZE */ 183 #define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ 184 185 /* Section 2: PHY configuration section */ 186 187 /* DP83848 PHY Address*/ 188 #define DP83848_PHY_ADDRESS 0x01U 189 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 190 #define PHY_RESET_DELAY 0x000000FFU 191 /* PHY Configuration delay */ 192 #define PHY_CONFIG_DELAY 0x00000FFFU 193 194 #define PHY_READ_TO 0x0000FFFFU 195 #define PHY_WRITE_TO 0x0000FFFFU 196 197 /* Section 3: Common PHY Registers */ 198 199 #define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */ 200 #define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */ 201 202 #define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ 203 #define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ 204 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ 205 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ 206 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ 207 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ 208 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ 209 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ 210 #define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ 211 #define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ 212 213 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ 214 #define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ 215 #define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ 216 217 /* Section 4: Extended PHY Registers */ 218 219 #define PHY_SR ((uint16_t)0x0010) /*!< PHY status register Offset */ 220 #define PHY_MICR ((uint16_t)0x0011) /*!< MII Interrupt Control Register */ 221 #define PHY_MISR ((uint16_t)0x0012) /*!< MII Interrupt Status and Misc. Control Register */ 222 223 #define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ 224 #define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ 225 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ 226 227 #define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ 228 #define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ 229 230 #define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ 231 #define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ 232 233 /* ################## SPI peripheral configuration ########################## */ 234 235 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver 236 * Activated: CRC code is present inside driver 237 * Deactivated: CRC code cleaned from driver 238 */ 239 240 #define USE_SPI_CRC 1U 241 242 /* Includes ------------------------------------------------------------------*/ 243 /** 244 * @brief Include module's header file 245 */ 246 247 #ifdef HAL_RCC_MODULE_ENABLED 248 #include "stm32f1xx_hal_rcc.h" 249 #endif /* HAL_RCC_MODULE_ENABLED */ 250 251 #ifdef HAL_GPIO_MODULE_ENABLED 252 #include "stm32f1xx_hal_gpio.h" 253 #endif /* HAL_GPIO_MODULE_ENABLED */ 254 255 #ifdef HAL_EXTI_MODULE_ENABLED 256 #include "stm32f1xx_hal_exti.h" 257 #endif /* HAL_EXTI_MODULE_ENABLED */ 258 259 #ifdef HAL_DMA_MODULE_ENABLED 260 #include "stm32f1xx_hal_dma.h" 261 #endif /* HAL_DMA_MODULE_ENABLED */ 262 263 #ifdef HAL_ETH_MODULE_ENABLED 264 #include "stm32f1xx_hal_eth.h" 265 #endif /* HAL_ETH_MODULE_ENABLED */ 266 267 #ifdef HAL_CAN_MODULE_ENABLED 268 #include "stm32f1xx_hal_can.h" 269 #endif /* HAL_CAN_MODULE_ENABLED */ 270 271 #ifdef HAL_CAN_LEGACY_MODULE_ENABLED 272 #include "Legacy/stm32f1xx_hal_can_legacy.h" 273 #endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ 274 275 #ifdef HAL_CEC_MODULE_ENABLED 276 #include "stm32f1xx_hal_cec.h" 277 #endif /* HAL_CEC_MODULE_ENABLED */ 278 279 #ifdef HAL_CORTEX_MODULE_ENABLED 280 #include "stm32f1xx_hal_cortex.h" 281 #endif /* HAL_CORTEX_MODULE_ENABLED */ 282 283 #ifdef HAL_ADC_MODULE_ENABLED 284 #include "stm32f1xx_hal_adc.h" 285 #endif /* HAL_ADC_MODULE_ENABLED */ 286 287 #ifdef HAL_CRC_MODULE_ENABLED 288 #include "stm32f1xx_hal_crc.h" 289 #endif /* HAL_CRC_MODULE_ENABLED */ 290 291 #ifdef HAL_DAC_MODULE_ENABLED 292 #include "stm32f1xx_hal_dac.h" 293 #endif /* HAL_DAC_MODULE_ENABLED */ 294 295 #ifdef HAL_FLASH_MODULE_ENABLED 296 #include "stm32f1xx_hal_flash.h" 297 #endif /* HAL_FLASH_MODULE_ENABLED */ 298 299 #ifdef HAL_SRAM_MODULE_ENABLED 300 #include "stm32f1xx_hal_sram.h" 301 #endif /* HAL_SRAM_MODULE_ENABLED */ 302 303 #ifdef HAL_NOR_MODULE_ENABLED 304 #include "stm32f1xx_hal_nor.h" 305 #endif /* HAL_NOR_MODULE_ENABLED */ 306 307 #ifdef HAL_I2C_MODULE_ENABLED 308 #include "stm32f1xx_hal_i2c.h" 309 #endif /* HAL_I2C_MODULE_ENABLED */ 310 311 #ifdef HAL_I2S_MODULE_ENABLED 312 #include "stm32f1xx_hal_i2s.h" 313 #endif /* HAL_I2S_MODULE_ENABLED */ 314 315 #ifdef HAL_IWDG_MODULE_ENABLED 316 #include "stm32f1xx_hal_iwdg.h" 317 #endif /* HAL_IWDG_MODULE_ENABLED */ 318 319 #ifdef HAL_PWR_MODULE_ENABLED 320 #include "stm32f1xx_hal_pwr.h" 321 #endif /* HAL_PWR_MODULE_ENABLED */ 322 323 #ifdef HAL_RTC_MODULE_ENABLED 324 #include "stm32f1xx_hal_rtc.h" 325 #endif /* HAL_RTC_MODULE_ENABLED */ 326 327 #ifdef HAL_PCCARD_MODULE_ENABLED 328 #include "stm32f1xx_hal_pccard.h" 329 #endif /* HAL_PCCARD_MODULE_ENABLED */ 330 331 #ifdef HAL_SD_MODULE_ENABLED 332 #include "stm32f1xx_hal_sd.h" 333 #endif /* HAL_SD_MODULE_ENABLED */ 334 335 #ifdef HAL_NAND_MODULE_ENABLED 336 #include "stm32f1xx_hal_nand.h" 337 #endif /* HAL_NAND_MODULE_ENABLED */ 338 339 #ifdef HAL_SPI_MODULE_ENABLED 340 #include "stm32f1xx_hal_spi.h" 341 #endif /* HAL_SPI_MODULE_ENABLED */ 342 343 #ifdef HAL_TIM_MODULE_ENABLED 344 #include "stm32f1xx_hal_tim.h" 345 #endif /* HAL_TIM_MODULE_ENABLED */ 346 347 #ifdef HAL_UART_MODULE_ENABLED 348 #include "stm32f1xx_hal_uart.h" 349 #endif /* HAL_UART_MODULE_ENABLED */ 350 351 #ifdef HAL_USART_MODULE_ENABLED 352 #include "stm32f1xx_hal_usart.h" 353 #endif /* HAL_USART_MODULE_ENABLED */ 354 355 #ifdef HAL_IRDA_MODULE_ENABLED 356 #include "stm32f1xx_hal_irda.h" 357 #endif /* HAL_IRDA_MODULE_ENABLED */ 358 359 #ifdef HAL_SMARTCARD_MODULE_ENABLED 360 #include "stm32f1xx_hal_smartcard.h" 361 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 362 363 #ifdef HAL_WWDG_MODULE_ENABLED 364 #include "stm32f1xx_hal_wwdg.h" 365 #endif /* HAL_WWDG_MODULE_ENABLED */ 366 367 #ifdef HAL_PCD_MODULE_ENABLED 368 #include "stm32f1xx_hal_pcd.h" 369 #endif /* HAL_PCD_MODULE_ENABLED */ 370 371 #ifdef HAL_HCD_MODULE_ENABLED 372 #include "stm32f1xx_hal_hcd.h" 373 #endif /* HAL_HCD_MODULE_ENABLED */ 374 375 #ifdef HAL_MMC_MODULE_ENABLED 376 #include "stm32f1xx_hal_mmc.h" 377 #endif /* HAL_MMC_MODULE_ENABLED */ 378 379 /* Exported macro ------------------------------------------------------------*/ 380 #ifdef USE_FULL_ASSERT 381 /** 382 * @brief The assert_param macro is used for function's parameters check. 383 * @param expr If expr is false, it calls assert_failed function 384 * which reports the name of the source file and the source 385 * line number of the call that failed. 386 * If expr is true, it returns no value. 387 * @retval None 388 */ 389 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) 390 /* Exported functions ------------------------------------------------------- */ 391 void assert_failed(uint8_t* file, uint32_t line); 392 #else 393 #define assert_param(expr) ((void)0U) 394 #endif /* USE_FULL_ASSERT */ 395 396 397 #ifdef __cplusplus 398 } 399 #endif 400 401 #endif /* __STM32F1xx_HAL_CONF_H */ 402 403 404
