1 /***************************************************************************//** 2 * @file 3 * @brief Power Amplifier configuration file. 4 ******************************************************************************* 5 * # License 6 * <b>Copyright 2020 Silicon Laboratories Inc. www.silabs.com</b> 7 ******************************************************************************* 8 * 9 * SPDX-License-Identifier: Zlib 10 * 11 * The licensor of this software is Silicon Laboratories Inc. 12 * 13 * This software is provided 'as-is', without any express or implied 14 * warranty. In no event will the authors be held liable for any damages 15 * arising from the use of this software. 16 * 17 * Permission is granted to anyone to use this software for any purpose, 18 * including commercial applications, and to alter it and redistribute it 19 * freely, subject to the following restrictions: 20 * 21 * 1. The origin of this software must not be misrepresented; you must not 22 * claim that you wrote the original software. If you use this software 23 * in a product, an acknowledgment in the product documentation would be 24 * appreciated but is not required. 25 * 2. Altered source versions must be plainly marked as such, and must not be 26 * misrepresented as being the original software. 27 * 3. This notice may not be removed or altered from any source distribution. 28 * 29 ******************************************************************************/ 30 31 #ifndef SL_RAIL_UTIL_PA_CONFIG_H 32 #define SL_RAIL_UTIL_PA_CONFIG_H 33 34 #include "rail_types.h" 35 36 // <<< Use Configuration Wizard in Context Menu >>> 37 38 // <h> PA Configuration 39 // <o SL_RAIL_UTIL_PA_POWER_DECI_DBM> Initial PA Power (deci-dBm, 100 = 10.0 dBm) 40 // <i> Default: 100 41 #define SL_RAIL_UTIL_PA_POWER_DECI_DBM 100 42 // <o SL_RAIL_UTIL_PA_RAMP_TIME_US> PA Ramp Time (microseconds) 43 // <0-65535:1> 44 // <i> Default: 10 45 #define SL_RAIL_UTIL_PA_RAMP_TIME_US 10 46 // <o SL_RAIL_UTIL_PA_VOLTAGE_MV> Milli-volts on PA supply pin (PA_VDD) 47 // <0-65535:1> 48 // <i> Default: 3300 49 #define SL_RAIL_UTIL_PA_VOLTAGE_MV 3300 50 // <o SL_RAIL_UTIL_PA_SELECTION_2P4GHZ> 2.4 GHz PA Selection 51 // <RAIL_TX_POWER_MODE_2P4GIG_HP=> High Power 52 // <RAIL_TX_POWER_MODE_2P4GIG_LP=> Low Power 53 // <RAIL_TX_POWER_MODE_NONE=> Disable 54 // <i> Default: RAIL_TX_POWER_MODE_2P4GIG_HP 55 #define SL_RAIL_UTIL_PA_SELECTION_2P4GHZ RAIL_TX_POWER_MODE_2P4GIG_HP 56 // <o SL_RAIL_UTIL_PA_SELECTION_SUBGHZ> Sub-1 GHz PA Selection 57 // <RAIL_TX_POWER_MODE_SUBGIG=> Enable 58 // <RAIL_TX_POWER_MODE_NONE=> Disable 59 // <i> Default: RAIL_TX_POWER_MODE_SUBGIG 60 #define SL_RAIL_UTIL_PA_SELECTION_SUBGHZ RAIL_TX_POWER_MODE_SUBGIG 61 // </h> 62 63 // <h> PA Curve Configuration 64 // <s.50 SL_RAIL_UTIL_PA_CURVE_HEADER> Header file containing custom PA curves 65 // <i> Default: "pa_curves_efr32.h" 66 #define SL_RAIL_UTIL_PA_CURVE_HEADER "pa_curves_efr32.h" 67 // <s.50 SL_RAIL_UTIL_PA_CURVE_TYPES> Header file containing PA curve types 68 // <i> Default: "pa_curve_types_efr32.h" 69 #define SL_RAIL_UTIL_PA_CURVE_TYPES "pa_curve_types_efr32.h" 70 // </h> 71 72 // <h> PA Calibration Configuration 73 // <q SL_RAIL_UTIL_PA_CALIBRATION_ENABLE> Apply PA Calibration Factory Offset 74 // <i> Default: 1 75 #define SL_RAIL_UTIL_PA_CALIBRATION_ENABLE 1 76 // </h> 77 78 // <<< end of configuration section >>> 79 80 #endif // SL_RAIL_UTIL_PA_CONFIG_H 81
