1 /**
2 ******************************************************************************
3 * @file stm32l5xx_ll_lpuart.c
4 * @author MCD Application Team
5 * @brief LPUART LL module driver.
6 ******************************************************************************
7 * @attention
8 *
9 * Copyright (c) 2019 STMicroelectronics.
10 * All rights reserved.
11 *
12 * This software is licensed under terms that can be found in the LICENSE file
13 * in the root directory of this software component.
14 * If no LICENSE file comes with this software, it is provided AS-IS.
15 *
16 ******************************************************************************
17 */
18 #if defined(USE_FULL_LL_DRIVER)
19
20 /* Includes ------------------------------------------------------------------*/
21 #include "stm32l5xx_ll_lpuart.h"
22 #include "stm32l5xx_ll_rcc.h"
23 #include "stm32l5xx_ll_bus.h"
24 #ifdef USE_FULL_ASSERT
25 #include "stm32_assert.h"
26 #else
27 #define assert_param(expr) ((void)0U)
28 #endif /* USE_FULL_ASSERT */
29
30 /** @addtogroup STM32L5xx_LL_Driver
31 * @{
32 */
33
34 #if defined (LPUART1)
35
36 /** @addtogroup LPUART_LL
37 * @{
38 */
39
40 /* Private types -------------------------------------------------------------*/
41 /* Private variables ---------------------------------------------------------*/
42 /* Private constants ---------------------------------------------------------*/
43 /** @addtogroup LPUART_LL_Private_Constants
44 * @{
45 */
46
47 /* Definition of default baudrate value used for LPUART initialisation */
48 #define LPUART_DEFAULT_BAUDRATE (9600U)
49
50 /**
51 * @}
52 */
53
54
55 /* Private macros ------------------------------------------------------------*/
56 /** @addtogroup LPUART_LL_Private_Macros
57 * @{
58 */
59
60 /* Check of parameters for configuration of LPUART registers */
61
62 #define IS_LL_LPUART_PRESCALER(__VALUE__) (((__VALUE__) == LL_LPUART_PRESCALER_DIV1) \
63 || ((__VALUE__) == LL_LPUART_PRESCALER_DIV2) \
64 || ((__VALUE__) == LL_LPUART_PRESCALER_DIV4) \
65 || ((__VALUE__) == LL_LPUART_PRESCALER_DIV6) \
66 || ((__VALUE__) == LL_LPUART_PRESCALER_DIV8) \
67 || ((__VALUE__) == LL_LPUART_PRESCALER_DIV10) \
68 || ((__VALUE__) == LL_LPUART_PRESCALER_DIV12) \
69 || ((__VALUE__) == LL_LPUART_PRESCALER_DIV16) \
70 || ((__VALUE__) == LL_LPUART_PRESCALER_DIV32) \
71 || ((__VALUE__) == LL_LPUART_PRESCALER_DIV64) \
72 || ((__VALUE__) == LL_LPUART_PRESCALER_DIV128) \
73 || ((__VALUE__) == LL_LPUART_PRESCALER_DIV256))
74
75 /* __BAUDRATE__ Depending on constraints applicable for LPUART BRR register */
76 /* value : */
77 /* - fck must be in the range [3 x baudrate, 4096 x baudrate] */
78 /* - LPUART_BRR register value should be >= 0x300 */
79 /* - LPUART_BRR register value should be <= 0xFFFFF (20 bits) */
80 /* Baudrate specified by the user should belong to [8, 40000000].*/
81 #define IS_LL_LPUART_BAUDRATE(__BAUDRATE__) (((__BAUDRATE__) <= 40000000U) && ((__BAUDRATE__) >= 8U))
82
83 /* __VALUE__ BRR content must be greater than or equal to 0x300. */
84 #define IS_LL_LPUART_BRR_MIN(__VALUE__) ((__VALUE__) >= 0x300U)
85
86 /* __VALUE__ BRR content must be lower than or equal to 0xFFFFF. */
87 #define IS_LL_LPUART_BRR_MAX(__VALUE__) ((__VALUE__) <= 0x000FFFFFU)
88
89 #define IS_LL_LPUART_DIRECTION(__VALUE__) (((__VALUE__) == LL_LPUART_DIRECTION_NONE) \
90 || ((__VALUE__) == LL_LPUART_DIRECTION_RX) \
91 || ((__VALUE__) == LL_LPUART_DIRECTION_TX) \
92 || ((__VALUE__) == LL_LPUART_DIRECTION_TX_RX))
93
94 #define IS_LL_LPUART_PARITY(__VALUE__) (((__VALUE__) == LL_LPUART_PARITY_NONE) \
95 || ((__VALUE__) == LL_LPUART_PARITY_EVEN) \
96 || ((__VALUE__) == LL_LPUART_PARITY_ODD))
97
98 #define IS_LL_LPUART_DATAWIDTH(__VALUE__) (((__VALUE__) == LL_LPUART_DATAWIDTH_7B) \
99 || ((__VALUE__) == LL_LPUART_DATAWIDTH_8B) \
100 || ((__VALUE__) == LL_LPUART_DATAWIDTH_9B))
101
102 #define IS_LL_LPUART_STOPBITS(__VALUE__) (((__VALUE__) == LL_LPUART_STOPBITS_1) \
103 || ((__VALUE__) == LL_LPUART_STOPBITS_2))
104
105 #define IS_LL_LPUART_HWCONTROL(__VALUE__) (((__VALUE__) == LL_LPUART_HWCONTROL_NONE) \
106 || ((__VALUE__) == LL_LPUART_HWCONTROL_RTS) \
107 || ((__VALUE__) == LL_LPUART_HWCONTROL_CTS) \
108 || ((__VALUE__) == LL_LPUART_HWCONTROL_RTS_CTS))
109
110 /**
111 * @}
112 */
113
114 /* Private function prototypes -----------------------------------------------*/
115
116 /* Exported functions --------------------------------------------------------*/
117 /** @addtogroup LPUART_LL_Exported_Functions
118 * @{
119 */
120
121 /** @addtogroup LPUART_LL_EF_Init
122 * @{
123 */
124
125 /**
126 * @brief De-initialize LPUART registers (Registers restored to their default values).
127 * @param LPUARTx LPUART Instance
128 * @retval An ErrorStatus enumeration value:
129 * - SUCCESS: LPUART registers are de-initialized
130 * - ERROR: not applicable
131 */
LL_LPUART_DeInit(const USART_TypeDef * LPUARTx)132 ErrorStatus LL_LPUART_DeInit(const USART_TypeDef *LPUARTx)
133 {
134 ErrorStatus status = SUCCESS;
135
136 /* Check the parameters */
137 assert_param(IS_LPUART_INSTANCE(LPUARTx));
138
139 if (LPUARTx == LPUART1)
140 {
141 /* Force reset of LPUART peripheral */
142 LL_APB1_GRP2_ForceReset(LL_APB1_GRP2_PERIPH_LPUART1);
143
144 /* Release reset of LPUART peripheral */
145 LL_APB1_GRP2_ReleaseReset(LL_APB1_GRP2_PERIPH_LPUART1);
146 }
147 else
148 {
149 status = ERROR;
150 }
151
152 return (status);
153 }
154
155 /**
156 * @brief Initialize LPUART registers according to the specified
157 * parameters in LPUART_InitStruct.
158 * @note As some bits in LPUART configuration registers can only be written when
159 * the LPUART is disabled (USART_CR1_UE bit =0),
160 * LPUART Peripheral should be in disabled state prior calling this function.
161 * Otherwise, ERROR result will be returned.
162 * @note Baud rate value stored in LPUART_InitStruct BaudRate field, should be valid (different from 0).
163 * @param LPUARTx LPUART Instance
164 * @param LPUART_InitStruct pointer to a @ref LL_LPUART_InitTypeDef structure
165 * that contains the configuration information for the specified LPUART peripheral.
166 * @retval An ErrorStatus enumeration value:
167 * - SUCCESS: LPUART registers are initialized according to LPUART_InitStruct content
168 * - ERROR: Problem occurred during LPUART Registers initialization
169 */
LL_LPUART_Init(USART_TypeDef * LPUARTx,const LL_LPUART_InitTypeDef * LPUART_InitStruct)170 ErrorStatus LL_LPUART_Init(USART_TypeDef *LPUARTx, const LL_LPUART_InitTypeDef *LPUART_InitStruct)
171 {
172 ErrorStatus status = ERROR;
173 uint32_t periphclk;
174
175 /* Check the parameters */
176 assert_param(IS_LPUART_INSTANCE(LPUARTx));
177 assert_param(IS_LL_LPUART_PRESCALER(LPUART_InitStruct->PrescalerValue));
178 assert_param(IS_LL_LPUART_BAUDRATE(LPUART_InitStruct->BaudRate));
179 assert_param(IS_LL_LPUART_DATAWIDTH(LPUART_InitStruct->DataWidth));
180 assert_param(IS_LL_LPUART_STOPBITS(LPUART_InitStruct->StopBits));
181 assert_param(IS_LL_LPUART_PARITY(LPUART_InitStruct->Parity));
182 assert_param(IS_LL_LPUART_DIRECTION(LPUART_InitStruct->TransferDirection));
183 assert_param(IS_LL_LPUART_HWCONTROL(LPUART_InitStruct->HardwareFlowControl));
184
185 /* LPUART needs to be in disabled state, in order to be able to configure some bits in
186 CRx registers. Otherwise (LPUART not in Disabled state) => return ERROR */
187 if (LL_LPUART_IsEnabled(LPUARTx) == 0U)
188 {
189 /*---------------------------- LPUART CR1 Configuration -----------------------
190 * Configure LPUARTx CR1 (LPUART Word Length, Parity and Transfer Direction bits) with parameters:
191 * - DataWidth: USART_CR1_M bits according to LPUART_InitStruct->DataWidth value
192 * - Parity: USART_CR1_PCE, USART_CR1_PS bits according to LPUART_InitStruct->Parity value
193 * - TransferDirection: USART_CR1_TE, USART_CR1_RE bits according to LPUART_InitStruct->TransferDirection value
194 */
195 MODIFY_REG(LPUARTx->CR1,
196 (USART_CR1_M | USART_CR1_PCE | USART_CR1_PS | USART_CR1_TE | USART_CR1_RE),
197 (LPUART_InitStruct->DataWidth | LPUART_InitStruct->Parity | LPUART_InitStruct->TransferDirection));
198
199 /*---------------------------- LPUART CR2 Configuration -----------------------
200 * Configure LPUARTx CR2 (Stop bits) with parameters:
201 * - Stop Bits: USART_CR2_STOP bits according to LPUART_InitStruct->StopBits value.
202 */
203 LL_LPUART_SetStopBitsLength(LPUARTx, LPUART_InitStruct->StopBits);
204
205 /*---------------------------- LPUART CR3 Configuration -----------------------
206 * Configure LPUARTx CR3 (Hardware Flow Control) with parameters:
207 * - HardwareFlowControl: USART_CR3_RTSE, USART_CR3_CTSE bits according
208 * to LPUART_InitStruct->HardwareFlowControl value.
209 */
210 LL_LPUART_SetHWFlowCtrl(LPUARTx, LPUART_InitStruct->HardwareFlowControl);
211
212 /*---------------------------- LPUART BRR Configuration -----------------------
213 * Retrieve Clock frequency used for LPUART Peripheral
214 */
215 periphclk = LL_RCC_GetLPUARTClockFreq(LL_RCC_LPUART1_CLKSOURCE);
216
217 /* Configure the LPUART Baud Rate :
218 - prescaler value is required
219 - valid baud rate value (different from 0) is required
220 - Peripheral clock as returned by RCC service, should be valid (different from 0).
221 */
222 if ((periphclk != LL_RCC_PERIPH_FREQUENCY_NO)
223 && (LPUART_InitStruct->BaudRate != 0U))
224 {
225 status = SUCCESS;
226 LL_LPUART_SetBaudRate(LPUARTx,
227 periphclk,
228 LPUART_InitStruct->PrescalerValue,
229 LPUART_InitStruct->BaudRate);
230
231 /* Check BRR is greater than or equal to 0x300 */
232 assert_param(IS_LL_LPUART_BRR_MIN(LPUARTx->BRR));
233
234 /* Check BRR is lower than or equal to 0xFFFFF */
235 assert_param(IS_LL_LPUART_BRR_MAX(LPUARTx->BRR));
236 }
237
238 /*---------------------------- LPUART PRESC Configuration -----------------------
239 * Configure LPUARTx PRESC (Prescaler) with parameters:
240 * - PrescalerValue: LPUART_PRESC_PRESCALER bits according to LPUART_InitStruct->PrescalerValue value.
241 */
242 LL_LPUART_SetPrescaler(LPUARTx, LPUART_InitStruct->PrescalerValue);
243 }
244
245 return (status);
246 }
247
248 /**
249 * @brief Set each @ref LL_LPUART_InitTypeDef field to default value.
250 * @param LPUART_InitStruct pointer to a @ref LL_LPUART_InitTypeDef structure
251 * whose fields will be set to default values.
252 * @retval None
253 */
254
LL_LPUART_StructInit(LL_LPUART_InitTypeDef * LPUART_InitStruct)255 void LL_LPUART_StructInit(LL_LPUART_InitTypeDef *LPUART_InitStruct)
256 {
257 /* Set LPUART_InitStruct fields to default values */
258 LPUART_InitStruct->PrescalerValue = LL_LPUART_PRESCALER_DIV1;
259 LPUART_InitStruct->BaudRate = LPUART_DEFAULT_BAUDRATE;
260 LPUART_InitStruct->DataWidth = LL_LPUART_DATAWIDTH_8B;
261 LPUART_InitStruct->StopBits = LL_LPUART_STOPBITS_1;
262 LPUART_InitStruct->Parity = LL_LPUART_PARITY_NONE ;
263 LPUART_InitStruct->TransferDirection = LL_LPUART_DIRECTION_TX_RX;
264 LPUART_InitStruct->HardwareFlowControl = LL_LPUART_HWCONTROL_NONE;
265 }
266
267 /**
268 * @}
269 */
270
271 /**
272 * @}
273 */
274
275 /**
276 * @}
277 */
278
279 #endif /* LPUART1 */
280
281 /**
282 * @}
283 */
284
285 #endif /* USE_FULL_LL_DRIVER */
286
