1 /** 2 ****************************************************************************** 3 * @file stm32f4xx_hal_conf_template.h 4 * @author MCD Application Team 5 * @brief HAL configuration template file. 6 * This file should be copied to the application folder and renamed 7 * to stm32f4xx_hal_conf.h. 8 ****************************************************************************** 9 * @attention 10 * 11 * <h2><center>© Copyright (c) 2017 STMicroelectronics. 12 * All rights reserved.</center></h2> 13 * 14 * This software component is licensed by ST under BSD 3-Clause license, 15 * the "License"; You may not use this file except in compliance with the 16 * License. You may obtain a copy of the License at: 17 * opensource.org/licenses/BSD-3-Clause 18 * 19 ****************************************************************************** 20 */ 21 22 /* Define to prevent recursive inclusion -------------------------------------*/ 23 #ifndef __STM32F4xx_HAL_CONF_H 24 #define __STM32F4xx_HAL_CONF_H 25 26 #ifdef __cplusplus 27 extern "C" { 28 #endif 29 30 /* Exported types ------------------------------------------------------------*/ 31 /* Exported constants --------------------------------------------------------*/ 32 33 /* ########################## Module Selection ############################## */ 34 /** 35 * @brief This is the list of modules to be used in the HAL driver 36 */ 37 #define HAL_MODULE_ENABLED 38 #define HAL_ADC_MODULE_ENABLED 39 #define HAL_CAN_MODULE_ENABLED 40 /* #define HAL_CAN_LEGACY_MODULE_ENABLED */ 41 #define HAL_CRC_MODULE_ENABLED 42 #define HAL_CEC_MODULE_ENABLED 43 #define HAL_CRYP_MODULE_ENABLED 44 #define HAL_DAC_MODULE_ENABLED 45 #define HAL_DCMI_MODULE_ENABLED 46 #define HAL_DMA_MODULE_ENABLED 47 #define HAL_DMA2D_MODULE_ENABLED 48 #define HAL_ETH_MODULE_ENABLED 49 #define HAL_FLASH_MODULE_ENABLED 50 #define HAL_NAND_MODULE_ENABLED 51 #define HAL_NOR_MODULE_ENABLED 52 #define HAL_PCCARD_MODULE_ENABLED 53 #define HAL_SRAM_MODULE_ENABLED 54 #define HAL_SDRAM_MODULE_ENABLED 55 #define HAL_HASH_MODULE_ENABLED 56 #define HAL_GPIO_MODULE_ENABLED 57 #define HAL_EXTI_MODULE_ENABLED 58 /* #define HAL_I2C_MODULE_ENABLED */ 59 #define HAL_SMBUS_MODULE_ENABLED 60 #define HAL_I2S_MODULE_ENABLED 61 #define HAL_IWDG_MODULE_ENABLED 62 #define HAL_LTDC_MODULE_ENABLED 63 #define HAL_DSI_MODULE_ENABLED 64 #define HAL_PWR_MODULE_ENABLED 65 #define HAL_QSPI_MODULE_ENABLED 66 #define HAL_RCC_MODULE_ENABLED 67 #define HAL_RNG_MODULE_ENABLED 68 #define HAL_RTC_MODULE_ENABLED 69 #define HAL_SAI_MODULE_ENABLED 70 #define HAL_SD_MODULE_ENABLED 71 #define HAL_SPI_MODULE_ENABLED 72 #define HAL_TIM_MODULE_ENABLED 73 #define HAL_UART_MODULE_ENABLED 74 #define HAL_USART_MODULE_ENABLED 75 #define HAL_IRDA_MODULE_ENABLED 76 #define HAL_SMARTCARD_MODULE_ENABLED 77 #define HAL_WWDG_MODULE_ENABLED 78 #define HAL_CORTEX_MODULE_ENABLED 79 #define HAL_PCD_MODULE_ENABLED 80 #define HAL_HCD_MODULE_ENABLED 81 #define HAL_FMPI2C_MODULE_ENABLED 82 #define HAL_FMPSMBUS_MODULE_ENABLED 83 #define HAL_SPDIFRX_MODULE_ENABLED 84 #define HAL_DFSDM_MODULE_ENABLED 85 #define HAL_LPTIM_MODULE_ENABLED 86 #define HAL_MMC_MODULE_ENABLED 87 88 /* ########################## HSE/HSI Values adaptation ##################### */ 89 /** 90 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 91 * This value is used by the RCC HAL module to compute the system frequency 92 * (when HSE is used as system clock source, directly or through the PLL). 93 */ 94 #if !defined (HSE_VALUE) 95 #define HSE_VALUE 25000000U /*!< Value of the External oscillator in Hz */ 96 #endif /* HSE_VALUE */ 97 98 #if !defined (HSE_STARTUP_TIMEOUT) 99 #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ 100 #endif /* HSE_STARTUP_TIMEOUT */ 101 102 /** 103 * @brief Internal High Speed oscillator (HSI) value. 104 * This value is used by the RCC HAL module to compute the system frequency 105 * (when HSI is used as system clock source, directly or through the PLL). 106 */ 107 #if !defined (HSI_VALUE) 108 #define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz */ 109 #endif /* HSI_VALUE */ 110 111 /** 112 * @brief Internal Low Speed oscillator (LSI) value. 113 */ 114 #if !defined (LSI_VALUE) 115 #define LSI_VALUE 32000U /*!< LSI Typical Value in Hz */ 116 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz 117 The real value may vary depending on the variations 118 in voltage and temperature. */ 119 /** 120 * @brief External Low Speed oscillator (LSE) value. 121 */ 122 #if !defined (LSE_VALUE) 123 #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */ 124 #endif /* LSE_VALUE */ 125 126 #if !defined (LSE_STARTUP_TIMEOUT) 127 #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ 128 #endif /* LSE_STARTUP_TIMEOUT */ 129 130 /** 131 * @brief External clock source for I2S peripheral 132 * This value is used by the I2S HAL module to compute the I2S clock source 133 * frequency, this source is inserted directly through I2S_CKIN pad. 134 */ 135 #if !defined (EXTERNAL_CLOCK_VALUE) 136 #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the External oscillator in Hz*/ 137 #endif /* EXTERNAL_CLOCK_VALUE */ 138 139 /* Tip: To avoid modifying this file each time you need to use different HSE, 140 === you can define the HSE value in your toolchain compiler preprocessor. */ 141 142 /* ########################### System Configuration ######################### */ 143 /** 144 * @brief This is the HAL system configuration section 145 */ 146 #define VDD_VALUE 3300U /*!< Value of VDD in mv */ 147 #define TICK_INT_PRIORITY 0x0FU /*!< tick interrupt priority */ 148 #define USE_RTOS 0U 149 #define PREFETCH_ENABLE 1U 150 #define INSTRUCTION_CACHE_ENABLE 1U 151 #define DATA_CACHE_ENABLE 1U 152 153 #define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ 154 #define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ 155 #define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ 156 #define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ 157 #define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ 158 #define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ 159 #define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ 160 #define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ 161 #define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ 162 #define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ 163 #define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ 164 #define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ 165 #define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ 166 #define USE_HAL_FMPI2C_REGISTER_CALLBACKS 0U /* FMPI2C register callback disabled */ 167 #define USE_HAL_FMPSMBUS_REGISTER_CALLBACKS 0U /* FMPSMBUS register callback disabled */ 168 #define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ 169 #define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ 170 #define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ 171 #define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ 172 #define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ 173 #define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ 174 #define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ 175 #define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ 176 #define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ 177 #define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ 178 #define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ 179 #define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ 180 #define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ 181 #define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ 182 #define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ 183 #define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ 184 #define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ 185 #define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ 186 #define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ 187 #define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ 188 #define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ 189 #define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ 190 #define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ 191 #define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ 192 193 /* ########################## Assert Selection ############################## */ 194 /** 195 * @brief Uncomment the line below to expanse the "assert_param" macro in the 196 * HAL drivers code 197 */ 198 /* #define USE_FULL_ASSERT 1U */ 199 200 /* ################## Ethernet peripheral configuration ##################### */ 201 202 /* Section 1 : Ethernet peripheral configuration */ 203 204 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ 205 #define MAC_ADDR0 2U 206 #define MAC_ADDR1 0U 207 #define MAC_ADDR2 0U 208 #define MAC_ADDR3 0U 209 #define MAC_ADDR4 0U 210 #define MAC_ADDR5 0U 211 212 /* Definition of the Ethernet driver buffers size and count */ 213 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ 214 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ 215 #define ETH_RXBUFNB 4U /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ 216 #define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ 217 218 /* Section 2: PHY configuration section */ 219 220 /* DP83848 PHY Address*/ 221 #define DP83848_PHY_ADDRESS 0x01U 222 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 223 #define PHY_RESET_DELAY 0x000000FFU 224 /* PHY Configuration delay */ 225 #define PHY_CONFIG_DELAY 0x00000FFFU 226 227 #define PHY_READ_TO 0x0000FFFFU 228 #define PHY_WRITE_TO 0x0000FFFFU 229 230 /* Section 3: Common PHY Registers */ 231 232 #define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */ 233 #define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */ 234 235 #define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ 236 #define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ 237 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ 238 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ 239 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ 240 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ 241 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ 242 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ 243 #define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ 244 #define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ 245 246 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ 247 #define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ 248 #define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ 249 250 /* Section 4: Extended PHY Registers */ 251 252 #define PHY_SR ((uint16_t)0x0010) /*!< PHY status register Offset */ 253 #define PHY_MICR ((uint16_t)0x0011) /*!< MII Interrupt Control Register */ 254 #define PHY_MISR ((uint16_t)0x0012) /*!< MII Interrupt Status and Misc. Control Register */ 255 256 #define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ 257 #define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ 258 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ 259 260 #define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ 261 #define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ 262 263 #define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ 264 #define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ 265 266 /* ################## SPI peripheral configuration ########################## */ 267 268 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver 269 * Activated: CRC code is present inside driver 270 * Deactivated: CRC code cleaned from driver 271 */ 272 273 #define USE_SPI_CRC 1U 274 275 /* Includes ------------------------------------------------------------------*/ 276 /** 277 * @brief Include module's header file 278 */ 279 280 #ifdef HAL_RCC_MODULE_ENABLED 281 #include "stm32f4xx_hal_rcc.h" 282 #endif /* HAL_RCC_MODULE_ENABLED */ 283 284 #ifdef HAL_GPIO_MODULE_ENABLED 285 #include "stm32f4xx_hal_gpio.h" 286 #endif /* HAL_GPIO_MODULE_ENABLED */ 287 288 #ifdef HAL_EXTI_MODULE_ENABLED 289 #include "stm32f4xx_hal_exti.h" 290 #endif /* HAL_EXTI_MODULE_ENABLED */ 291 292 #ifdef HAL_DMA_MODULE_ENABLED 293 #include "stm32f4xx_hal_dma.h" 294 #endif /* HAL_DMA_MODULE_ENABLED */ 295 296 #ifdef HAL_CORTEX_MODULE_ENABLED 297 #include "stm32f4xx_hal_cortex.h" 298 #endif /* HAL_CORTEX_MODULE_ENABLED */ 299 300 #ifdef HAL_ADC_MODULE_ENABLED 301 #include "stm32f4xx_hal_adc.h" 302 #endif /* HAL_ADC_MODULE_ENABLED */ 303 304 #ifdef HAL_CAN_MODULE_ENABLED 305 #include "stm32f4xx_hal_can.h" 306 #endif /* HAL_CAN_MODULE_ENABLED */ 307 308 #ifdef HAL_CAN_LEGACY_MODULE_ENABLED 309 #include "stm32f4xx_hal_can_legacy.h" 310 #endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ 311 312 #ifdef HAL_CRC_MODULE_ENABLED 313 #include "stm32f4xx_hal_crc.h" 314 #endif /* HAL_CRC_MODULE_ENABLED */ 315 316 #ifdef HAL_CRYP_MODULE_ENABLED 317 #include "stm32f4xx_hal_cryp.h" 318 #endif /* HAL_CRYP_MODULE_ENABLED */ 319 320 #ifdef HAL_DMA2D_MODULE_ENABLED 321 #include "stm32f4xx_hal_dma2d.h" 322 #endif /* HAL_DMA2D_MODULE_ENABLED */ 323 324 #ifdef HAL_DAC_MODULE_ENABLED 325 #include "stm32f4xx_hal_dac.h" 326 #endif /* HAL_DAC_MODULE_ENABLED */ 327 328 #ifdef HAL_DCMI_MODULE_ENABLED 329 #include "stm32f4xx_hal_dcmi.h" 330 #endif /* HAL_DCMI_MODULE_ENABLED */ 331 332 #ifdef HAL_ETH_MODULE_ENABLED 333 #include "stm32f4xx_hal_eth.h" 334 #endif /* HAL_ETH_MODULE_ENABLED */ 335 336 #ifdef HAL_FLASH_MODULE_ENABLED 337 #include "stm32f4xx_hal_flash.h" 338 #endif /* HAL_FLASH_MODULE_ENABLED */ 339 340 #ifdef HAL_SRAM_MODULE_ENABLED 341 #include "stm32f4xx_hal_sram.h" 342 #endif /* HAL_SRAM_MODULE_ENABLED */ 343 344 #ifdef HAL_NOR_MODULE_ENABLED 345 #include "stm32f4xx_hal_nor.h" 346 #endif /* HAL_NOR_MODULE_ENABLED */ 347 348 #ifdef HAL_NAND_MODULE_ENABLED 349 #include "stm32f4xx_hal_nand.h" 350 #endif /* HAL_NAND_MODULE_ENABLED */ 351 352 #ifdef HAL_PCCARD_MODULE_ENABLED 353 #include "stm32f4xx_hal_pccard.h" 354 #endif /* HAL_PCCARD_MODULE_ENABLED */ 355 356 #ifdef HAL_SDRAM_MODULE_ENABLED 357 #include "stm32f4xx_hal_sdram.h" 358 #endif /* HAL_SDRAM_MODULE_ENABLED */ 359 360 #ifdef HAL_HASH_MODULE_ENABLED 361 #include "stm32f4xx_hal_hash.h" 362 #endif /* HAL_HASH_MODULE_ENABLED */ 363 364 #ifdef HAL_I2C_MODULE_ENABLED 365 #include "stm32f4xx_hal_i2c.h" 366 #endif /* HAL_I2C_MODULE_ENABLED */ 367 368 #ifdef HAL_SMBUS_MODULE_ENABLED 369 #include "stm32f4xx_hal_smbus.h" 370 #endif /* HAL_SMBUS_MODULE_ENABLED */ 371 372 #ifdef HAL_I2S_MODULE_ENABLED 373 #include "stm32f4xx_hal_i2s.h" 374 #endif /* HAL_I2S_MODULE_ENABLED */ 375 376 #ifdef HAL_IWDG_MODULE_ENABLED 377 #include "stm32f4xx_hal_iwdg.h" 378 #endif /* HAL_IWDG_MODULE_ENABLED */ 379 380 #ifdef HAL_LTDC_MODULE_ENABLED 381 #include "stm32f4xx_hal_ltdc.h" 382 #endif /* HAL_LTDC_MODULE_ENABLED */ 383 384 #ifdef HAL_PWR_MODULE_ENABLED 385 #include "stm32f4xx_hal_pwr.h" 386 #endif /* HAL_PWR_MODULE_ENABLED */ 387 388 #ifdef HAL_RNG_MODULE_ENABLED 389 #include "stm32f4xx_hal_rng.h" 390 #endif /* HAL_RNG_MODULE_ENABLED */ 391 392 #ifdef HAL_RTC_MODULE_ENABLED 393 #include "stm32f4xx_hal_rtc.h" 394 #endif /* HAL_RTC_MODULE_ENABLED */ 395 396 #ifdef HAL_SAI_MODULE_ENABLED 397 #include "stm32f4xx_hal_sai.h" 398 #endif /* HAL_SAI_MODULE_ENABLED */ 399 400 #ifdef HAL_SD_MODULE_ENABLED 401 #include "stm32f4xx_hal_sd.h" 402 #endif /* HAL_SD_MODULE_ENABLED */ 403 404 #ifdef HAL_SPI_MODULE_ENABLED 405 #include "stm32f4xx_hal_spi.h" 406 #endif /* HAL_SPI_MODULE_ENABLED */ 407 408 #ifdef HAL_TIM_MODULE_ENABLED 409 #include "stm32f4xx_hal_tim.h" 410 #endif /* HAL_TIM_MODULE_ENABLED */ 411 412 #ifdef HAL_UART_MODULE_ENABLED 413 #include "stm32f4xx_hal_uart.h" 414 #endif /* HAL_UART_MODULE_ENABLED */ 415 416 #ifdef HAL_USART_MODULE_ENABLED 417 #include "stm32f4xx_hal_usart.h" 418 #endif /* HAL_USART_MODULE_ENABLED */ 419 420 #ifdef HAL_IRDA_MODULE_ENABLED 421 #include "stm32f4xx_hal_irda.h" 422 #endif /* HAL_IRDA_MODULE_ENABLED */ 423 424 #ifdef HAL_SMARTCARD_MODULE_ENABLED 425 #include "stm32f4xx_hal_smartcard.h" 426 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 427 428 #ifdef HAL_WWDG_MODULE_ENABLED 429 #include "stm32f4xx_hal_wwdg.h" 430 #endif /* HAL_WWDG_MODULE_ENABLED */ 431 432 #ifdef HAL_PCD_MODULE_ENABLED 433 #include "stm32f4xx_hal_pcd.h" 434 #endif /* HAL_PCD_MODULE_ENABLED */ 435 436 #ifdef HAL_HCD_MODULE_ENABLED 437 #include "stm32f4xx_hal_hcd.h" 438 #endif /* HAL_HCD_MODULE_ENABLED */ 439 440 #ifdef HAL_DSI_MODULE_ENABLED 441 #include "stm32f4xx_hal_dsi.h" 442 #endif /* HAL_DSI_MODULE_ENABLED */ 443 444 #ifdef HAL_QSPI_MODULE_ENABLED 445 #include "stm32f4xx_hal_qspi.h" 446 #endif /* HAL_QSPI_MODULE_ENABLED */ 447 448 #ifdef HAL_CEC_MODULE_ENABLED 449 #include "stm32f4xx_hal_cec.h" 450 #endif /* HAL_CEC_MODULE_ENABLED */ 451 452 #ifdef HAL_FMPI2C_MODULE_ENABLED 453 #include "stm32f4xx_hal_fmpi2c.h" 454 #endif /* HAL_FMPI2C_MODULE_ENABLED */ 455 456 #ifdef HAL_FMPSMBUS_MODULE_ENABLED 457 #include "stm32f4xx_hal_fmpsmbus.h" 458 #endif /* HAL_FMPSMBUS_MODULE_ENABLED */ 459 460 #ifdef HAL_SPDIFRX_MODULE_ENABLED 461 #include "stm32f4xx_hal_spdifrx.h" 462 #endif /* HAL_SPDIFRX_MODULE_ENABLED */ 463 464 #ifdef HAL_DFSDM_MODULE_ENABLED 465 #include "stm32f4xx_hal_dfsdm.h" 466 #endif /* HAL_DFSDM_MODULE_ENABLED */ 467 468 #ifdef HAL_LPTIM_MODULE_ENABLED 469 #include "stm32f4xx_hal_lptim.h" 470 #endif /* HAL_LPTIM_MODULE_ENABLED */ 471 472 #ifdef HAL_MMC_MODULE_ENABLED 473 #include "stm32f4xx_hal_mmc.h" 474 #endif /* HAL_MMC_MODULE_ENABLED */ 475 476 /* Exported macro ------------------------------------------------------------*/ 477 #ifdef USE_FULL_ASSERT 478 /** 479 * @brief The assert_param macro is used for function's parameters check. 480 * @param expr If expr is false, it calls assert_failed function 481 * which reports the name of the source file and the source 482 * line number of the call that failed. 483 * If expr is true, it returns no value. 484 * @retval None 485 */ 486 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) 487 /* Exported functions ------------------------------------------------------- */ 488 void assert_failed(uint8_t* file, uint32_t line); 489 #else 490 #define assert_param(expr) ((void)0U) 491 #endif /* USE_FULL_ASSERT */ 492 493 494 #ifdef __cplusplus 495 } 496 #endif 497 498 #endif /* __STM32F4xx_HAL_CONF_H */ 499 500 501 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ 502
