1 /* 2 * Copyright (c) 2019-2020, ARM Limited and Contributors. All rights reserved. 3 * 4 * SPDX-License-Identifier: BSD-3-Clause 5 */ 6 7 #ifndef BRCM_SCPI_H 8 #define BRCM_SCPI_H 9 10 #include <stddef.h> 11 #include <stdint.h> 12 13 /* 14 * An SCPI command consists of a header and a payload. 15 * The following structure describes the header. It is 64-bit long. 16 */ 17 typedef struct { 18 /* Command ID */ 19 uint32_t id : 7; 20 /* Set ID. Identifies whether this is a standard or extended command. */ 21 uint32_t set : 1; 22 /* Sender ID to match a reply. The value is sender specific. */ 23 uint32_t sender : 8; 24 /* Size of the payload in bytes (0 - 511) */ 25 uint32_t size : 9; 26 uint32_t reserved : 7; 27 /* 28 * Status indicating the success of a command. 29 * See the enum below. 30 */ 31 uint32_t status; 32 } scpi_cmd_t; 33 34 typedef enum { 35 SCPI_SET_NORMAL = 0, /* Normal SCPI commands */ 36 SCPI_SET_EXTENDED /* Extended SCPI commands */ 37 } scpi_set_t; 38 39 enum { 40 SCP_OK = 0, /* Success */ 41 SCP_E_PARAM, /* Invalid parameter(s) */ 42 SCP_E_ALIGN, /* Invalid alignment */ 43 SCP_E_SIZE, /* Invalid size */ 44 SCP_E_HANDLER, /* Invalid handler or callback */ 45 SCP_E_ACCESS, /* Invalid access or permission denied */ 46 SCP_E_RANGE, /* Value out of range */ 47 SCP_E_TIMEOUT, /* Time out has ocurred */ 48 SCP_E_NOMEM, /* Invalid memory area or pointer */ 49 SCP_E_PWRSTATE, /* Invalid power state */ 50 SCP_E_SUPPORT, /* Feature not supported or disabled */ 51 SCPI_E_DEVICE, /* Device error */ 52 SCPI_E_BUSY, /* Device is busy */ 53 }; 54 55 typedef uint32_t scpi_status_t; 56 typedef enum { 57 SCPI_CMD_SCP_READY = 0x01, 58 SCPI_CMD_SET_POWER_STATE = 0x03, 59 SCPI_CMD_GET_POWER_STATE = 0x04, 60 SCPI_CMD_SYS_POWER_STATE = 0x05 61 } scpi_command_t; 62 63 /* 64 * Macros to parse SCP response to GET_POWER_STATE command 65 * 66 * [3:0] : cluster ID 67 * [7:4] : cluster state: 0 = on; 3 = off; rest are reserved 68 * [15:8]: on/off state for individual CPUs in the cluster 69 * 70 * Payload is in little-endian 71 */ 72 #define CLUSTER_ID(_resp) ((_resp) & 0xf) 73 #define CLUSTER_POWER_STATE(_resp) (((_resp) >> 4) & 0xf) 74 75 /* Result is a bit mask of CPU on/off states in the cluster */ 76 #define CPU_POWER_STATE(_resp) (((_resp) >> 8) & 0xff) 77 78 /* 79 * For GET_POWER_STATE, SCP returns the power states of every cluster. The 80 * size of response depends on the number of clusters in the system. The 81 * SCP-to-AP payload contains 2 bytes per cluster. Make sure the response is 82 * large enough to contain power states of a given cluster 83 */ 84 #define CHECK_RESPONSE(_resp, _clus) (_resp.size >= (((_clus) + 1) * 2)) 85 86 typedef enum { 87 scpi_power_on = 0, 88 scpi_power_retention = 1, 89 scpi_power_off = 3, 90 } scpi_power_state_t; 91 92 typedef enum { 93 scpi_system_shutdown = 0, 94 scpi_system_reboot = 1, 95 scpi_system_reset = 2 96 } scpi_system_state_t; 97 98 extern int scpi_wait_ready(void); 99 extern void scpi_set_brcm_power_state(unsigned int mpidr, 100 scpi_power_state_t cpu_state, 101 scpi_power_state_t cluster_state, 102 scpi_power_state_t css_state); 103 int scpi_get_brcm_power_state(unsigned int mpidr, unsigned int *cpu_state_p, 104 unsigned int *cluster_state_p); 105 uint32_t scpi_sys_power_state(scpi_system_state_t system_state); 106 107 #endif /* BRCM_SCPI_H */ 108
