Home
last modified time | relevance | path

Searched full:upon (Results 1 – 25 of 276) sorted by relevance

12345678910>>...12

/Zephyr-latest/drivers/wifi/nrf_wifi/inc/
Dcoex.h35 * Returns zero upon successful configuration.
36 * Returns non-zero upon unsuccessful configuration.
51 * Returns zero upon successful configuration.
52 * Returns non-zero upon unsuccessful configuration.
68 * Returns zero upon successful configuration.
69 * Returns non-zero upon unsuccessful configuration.
79 * Returns zero upon successful configuration.
80 * Returns non-zero upon unsuccessful configuration.
/Zephyr-latest/include/zephyr/drivers/can/
Dcan_sja1000.h186 * @brief SJA1000 callback API upon setting CAN bus timing
192 * @brief SJA1000 callback API upon getting CAN controller capabilities
198 * @brief SJA1000 callback API upon starting CAN controller
204 * @brief SJA1000 callback API upon stopping CAN controller
210 * @brief SJA1000 callback API upon setting CAN controller mode
216 * @brief SJA1000 callback API upon sending a CAN frame
223 * @brief SJA1000 callback API upon adding an RX filter
230 * @brief SJA1000 callback API upon removing an RX filter
237 * @brief SJA1000 callback API upon recovering the CAN bus
244 * @brief SJA1000 callback API upon getting the CAN controller state
[all …]
Dtransceiver.h33 * @brief Callback API upon enabling CAN transceiver
39 * @brief Callback API upon disabling CAN transceiver
/Zephyr-latest/tests/bluetooth/host/id/bt_id_set_create_conn_own_addr/src/
Dmain.c36 * isn't called and address type reference is updated upon success.
65 * set_random_address() is called and address type reference is updated upon success.
99 * updated upon success.
131 * is updated upon success.
/Zephyr-latest/tests/subsys/testsuite/fff_fake_contexts/include/zephyr/
Dcalled_API.h30 * @return zero(0) upon success, with *instance_out updated.
47 * @return zero(0) upon success, with instance invalidated.
Dcode_under_test.h25 * @return zero(0) upon success
/Zephyr-latest/tests/bluetooth/host/id/bt_id_set_scan_own_addr/src/
Dmain.c50 * Address type reference is updated upon success.
82 * upon success.
118 * updated upon success.
150 * is updated upon success.
/Zephyr-latest/arch/arm/core/cortex_m/
Dprep_c.c86 * Upon reset, the Co-Processor Access Control Register is, normally, in z_arm_floating_point_init()
105 * Upon reset, the FPU Context Control Register is 0xC0000000 in z_arm_floating_point_init()
111 * FPCA bit in the CONTROL register), upon exception entries, in z_arm_floating_point_init()
126 * preservation the volatile FP registers will not be stacked upon in z_arm_floating_point_init()
163 * Upon reset, the CONTROL.FPCA bit is, normally, cleared. However, in z_arm_floating_point_init()
/Zephyr-latest/include/zephyr/drivers/
Deeprom.h44 * @brief Callback API upon reading from the EEPROM.
52 * @brief Callback API upon writing to the EEPROM.
59 * @brief Callback API upon getting the EEPROM size.
/Zephyr-latest/drivers/gpio/
DKconfig.sedi13 This driver is simply a shim driver built upon the SEDI
/Zephyr-latest/drivers/spi/
DKconfig.sedi13 This driver is simply a shim driver built upon the SEDI
/Zephyr-latest/drivers/serial/
DKconfig.sedi14 This driver is simply a shim driver built upon the SEDI
/Zephyr-latest/drivers/ipm/
DKconfig.sedi10 This driver is simply a shim driver built upon the SEDI
/Zephyr-latest/drivers/i2c/
DKconfig.sedi13 This driver is simply a shim driver built upon the SEDI
/Zephyr-latest/drivers/dma/
DKconfig.sedi13 This driver is simply a shim driver built upon the SEDI
DKconfig.nxp_edma23 driver will return an error upon configuration.
/Zephyr-latest/dts/bindings/sensor/
Dnxp,fxos8700-common.yaml95 threshold. The resolution depends upon the sample rate (ODR) and the
106 resolution depends upon the sample rate (ODR) and the high-pass filter
121 PULSE_WIND register. The resolution depends upon the sample rate (ODR)
/Zephyr-latest/drivers/watchdog/
Dwdt_intel_adsp.h49 * When set, it allow the DSP Core reset to take place upon second time out of the
122 * When set, it allow the DSP Core reset to take place upon second time out of the watchdog timer.
136 * When set, it allow the DSP Core reset to take place upon second time out of the
/Zephyr-latest/drivers/stepper/
DKconfig.stepper_event_template5 bool "$(module-str) guarantee non ISR callbacks upon stepper events"
/Zephyr-latest/drivers/sensor/ti/ina226/
DKconfig21 INA226 based upon the SHUNT_CAL register. This value is useful for
/Zephyr-latest/drivers/hwinfo/
Dhwinfo_ambiq.c54 /* Print out reset status register upon entry */ in z_impl_hwinfo_get_reset_cause()
120 * INFO1 space even upon clearing RSTGEN->STAT in z_impl_hwinfo_clear_reset_cause()
/Zephyr-latest/include/zephyr/drivers/serial/
Duart_altera.h15 * Driver will trigger interrupt upon receiving end of package character.
/Zephyr-latest/arch/x86/include/
Dkernel_arch_func.h48 /* Called upon CPU exception that is unhandled and hence fatal; dump
54 /* Called upon unrecoverable error; dump registers and transfer control to
/Zephyr-latest/subsys/ipc/ipc_service/backends/
DKconfig.rpmsg18 Some platforms retain the memory content upon reset. This is
/Zephyr-latest/drivers/timer/
DKconfig.arm_arch25 indication upon every actual timer interrupt. This option activates

12345678910>>...12