Searched full:switches (Results 1 – 25 of 166) sorted by relevance
1234567
| /Zephyr-latest/boards/arduino/opta/dts/bindings/ |
| D | gpio-power-switches.yaml | 6 or other kinds of power switches controlled by a GPIO. Each power
7 switch is defined in a child node of the gpio-power-switches node.
9 compatible: "gpio-power-switches"
|
| /Zephyr-latest/tests/benchmarks/sched/ |
| D | README.rst | 14 (the kernel switches to the partner thread)
16 (the kernel switches to the main thread)
|
| /Zephyr-latest/drivers/input/ |
| D | Kconfig.sbus | 44 SBUS sends analogue values for digital switches. This config value
51 SBUS sends analogue values for digital switches. This config value
|
| /Zephyr-latest/arch/arc/core/dsp/ |
| D | Kconfig | 26 across context switches to allow multiple threads to perform concurrent
50 across context switches to allow multiple threads to perform concurrent
|
| /Zephyr-latest/samples/net/openthread/coprocessor/ |
| D | overlay-rcp.conf | 1 # This overlay switches from NCP to RCP, use in combination with prj.conf
|
| /Zephyr-latest/tests/benchmarks/thread_metric/ |
| D | Kconfig | 51 of a thread. The total number of context switches is reported every
73 cyclical pattern. The total number of context switches is reported
|
| /Zephyr-latest/samples/bluetooth/mesh_demo/ |
| D | prj.conf | 43 # it switches to its internal memory management functions.
|
| /Zephyr-latest/drivers/timer/ |
| D | Kconfig.nrf_xrtc | 24 startup time and then seamlessly switches to the target clock source when
|
| /Zephyr-latest/samples/bluetooth/direction_finding_peripheral/boards/ |
| D | nrf52833dk_nrf52833.overlay | 21 * Pin numbers are selected to drive switches on antenna matrix
|
| /Zephyr-latest/samples/bluetooth/direction_finding_central/boards/ |
| D | nrf52833dk_nrf52833.overlay | 21 * Pin numbers are selected to drive switches on antenna matrix
|
| /Zephyr-latest/boards/adi/eval_adin1110ebz/doc/ |
| D | index.rst | 16 configuration links and switches. On-board LEDs provide status indication.
25 S201 DIP switches are shipped in Open Alliance SPI mode. The current Zephyr
27 so the S201 DIP switches must be set as ``SPI_CFG0 OFF`` and ``SPI_CFG1 ON``.
28 An inconsistent S201 DIP switches configuration will halt the boot.
|
| /Zephyr-latest/boards/adi/eval_adin2111ebz/doc/ |
| D | index.rst | 22 hardware configuration pins jumper and switches. The 2x On-board Activity LEDs provide Link
33 S1 DIP switches are shipped in Open Alliance SPI mode. The current Zephyr
35 so the S1 DIP switches must be set as ``SPI_CFG0 OFF and SPI_CFG1 OFF``.
36 An inconsistent S1 DIP switches configuration will halt the boot.
|
| /Zephyr-latest/dts/bindings/input/ |
| D | futaba,sbus.yaml | 7 to send out analogue joystick and switches output.
|
| /Zephyr-latest/subsys/sd/ |
| D | sd_ops.h | 12 * Switches voltage of SD card to 1.8V, as described by
|
| /Zephyr-latest/boards/sparkfun/thing_plus/doc/ |
| D | index.rst | 53 Push buttons and Switches
134 There are 2 samples that allow you to test that the buttons (switches) and LEDs on
|
| /Zephyr-latest/boards/circuitdojo/feather/doc/ |
| D | index.rst | 57 Push buttons and Switches
142 There are 2 samples that allow you to test that the buttons (switches) and LEDs on
|
| /Zephyr-latest/tests/benchmarks/sched/src/ |
| D | main.c | 22 * (the kernel switches to the partner thread)
24 * (the kernel switches to the main thread)
|
| /Zephyr-latest/scripts/checkpatch/ |
| D | timestamp | 19 # Some switches can be mixed and matched, eg. -Sa gives 2015-01-14-18-13
|
| /Zephyr-latest/soc/st/stm32/stm32f0x/ |
| D | soc.c | 36 * Alternatively both switches SW_VECTOR_RELAY (for Bootloader image) and
|
| /Zephyr-latest/boards/nordic/nrf9160dk/dts/bindings/ |
| D | nordic,nrf9160dk-nrf52840-interface.yaml | 26 analog switches that control the routing of involved nRF9160 pins must be
|
| /Zephyr-latest/boards/altr/max10/doc/ |
| D | index.rst | 15 There are two sets of switches on the back of the board. Of particular
26 :alt: Altera's MAX* 10 Switches
28 Other switches are user switches, their position is application-specific.
|
| /Zephyr-latest/boards/intel/socfpga_std/cyclonev_socdk/doc/ |
| D | index.rst | 28 There are two sets of switches on the back of the board. Of particular
44 Then, the board switches need to be configured as follows:
51 Other switches are user switches, their position is application-specific.
52 Refer to the development kit user manual for specifics about jumpers and switches
|
| /Zephyr-latest/samples/boards/phytec/reel_board/mesh_badge/ |
| D | README.rst | 38 #. Once disconnected the board switches over to Bluetooth Mesh mode, and you
|
| /Zephyr-latest/soc/nxp/lpc/lpc55xxx/ |
| D | pinctrl_soc.h | 22 /* LPC55S36 has two analog switches, and no IOCON_PIO_ASW definitions */
|
| /Zephyr-latest/boards/snps/em_starterkit/doc/ |
| D | index.rst | 45 3 buttons, and 4 dip switches that can be used with GPIO.
95 switches, 9 LEDs, SDCard on SPI, and a 16MB SPI-Flash memory.
187 switches should be UP except for switch 1. Other configuration choices
189 all dip switches should be UP except for switch 2. Next press the button
|
1234567
