Searched +full:strong +full:- +full:medium +full:- +full:edge (Results 1 – 5 of 5) sorted by relevance
3 * SPDX-License-Identifier: Apache-2.06 #include <infineon/cat3/xmc/xmc4700_F144x2048-pinctrl.dtsi>9 drive-strength = "strong-soft-edge";10 drive-push-pull;15 drive-strength = "strong-soft-edge";20 drive-strength = "strong-soft-edge";21 drive-push-pull;26 drive-strength = "strong-soft-edge";31 drive-strength = "strong-soft-edge";32 drive-push-pull;[all …]
3 * SPDX-License-Identifier: Apache-2.06 #include <infineon/cat3/xmc/xmc4500_F100x1024-pinctrl.dtsi>9 drive-strength = "strong-soft-edge";10 drive-push-pull;15 drive-strength = "strong-soft-edge";20 drive-strength = "strong-medium-edge";21 drive-push-pull;26 drive-strength = "strong-medium-edge";27 drive-push-pull;32 drive-strength = "strong-sharp-edge";[all …]
2 # SPDX-License-Identifier: Apache-2.012 compatible = "infineon,xmc4xxx-uart";13 pinctrl-0 = <&uart_tx_p0_1_u1c1 &uart_rx_p0_0_u1c1>;14 pinctrl-names = "default";15 input-src = "DX0D";19 pinctrl-0 is the phandle that stores the pin settings for two pins: &uart_tx_p0_1_u1c120 and &uart_rx_p0_0_u1c1. These nodes are pre-defined and their naming convention is designed24 The pre-defined nodes only set the alternate function of the output pin. The27 to the inherited property-allowlist list from pincfg-node.yaml).31 #include <zephyr/dt-bindings/pinctrl/xmc4xxx-pinctrl.h>[all …]
2 # SPDX-License-Identifier: Apache-2.012 dts/arm/infineon/xmc4xxx_xxx-pinctrl.dtsi24 The pwm ccu4 node must define the slice-prescaler values and the pinctrl nodes:26 slice-prescaler = <15 15 15 15>;27 pinctrl-0 = <&pwm_out_p1_1_ccu40_ch2>;28 pinctrl-names = "default";39 The pin should be configured with drive-push-pull bool option and hwctrl should be set40 to disabled. The drive-strength field can be set to any of the supported values:42 drive-strength = "strong-medium-edge";43 drive-push-pull;[all …]
4 * SPDX-License-Identifier: Apache-2.013 #include <zephyr/dt-bindings/gpio/infineon-xmc4xxx-gpio.h>42 return -ENOTSUP; in gpio_xmc4xxx_convert_flags()46 return -ENOTSUP; in gpio_xmc4xxx_convert_flags()50 pin_config->mode = XMC_GPIO_MODE_INPUT_TRISTATE; in gpio_xmc4xxx_convert_flags()52 pin_config->mode = XMC_GPIO_MODE_INPUT_PULL_DOWN; in gpio_xmc4xxx_convert_flags()55 pin_config->mode = XMC_GPIO_MODE_INPUT_PULL_UP; in gpio_xmc4xxx_convert_flags()61 return -EINVAL; in gpio_xmc4xxx_convert_flags()65 pin_config->mode = XMC_GPIO_MODE_OUTPUT_PUSH_PULL; in gpio_xmc4xxx_convert_flags()67 pin_config->mode = XMC_GPIO_MODE_OUTPUT_OPEN_DRAIN; in gpio_xmc4xxx_convert_flags()[all …]
