Searched full:settling (Results 1 – 22 of 22) sorted by relevance
| /Zephyr-latest/dts/bindings/adc/ |
| D | atmel,sam-adc.yaml | 32 settling-time:
36 ADC settling time in ADC clock cycles. When the gain, offset
39 settling time before starting the tracking phase.
|
| /Zephyr-latest/soc/nxp/imxrt/imxrt6xx/ |
| D | Kconfig | 53 int "System oscillator settling time"
55 Set the board system oscillator settling time in us. This should be set by the
|
| /Zephyr-latest/dts/bindings/input/ |
| D | st,stmpe811.yaml | 41 panel-driver-settling-time-us:
54 Panel driver settling time (microseconds). For large panels (> 6"), a capacitor of 10 nF
56 As a general rule, 1-5 nF capacitors require around 500 us settling time, and 5-10 nF need
|
| /Zephyr-latest/dts/bindings/net/wireless/ |
| D | generic-fem-two-ctrl-pins.yaml | 38 Desired minimum settling time, in microseconds, from
44 Desired minimum settling time, in microseconds, from
|
| D | nordic,nrf21540-fem.yaml | 100 Settling time in microseconds from state PG to TX.
109 Settling time in microseconds from state PG to RX.
118 Settling time in microseconds from state PD to PG.
|
| /Zephyr-latest/dts/bindings/regulator/ |
| D | regulator.yaml | 93 regulator-settling-time-us:
96 Settling time, in microseconds, for voltage change if regulator have the
100 regulator-settling-time-up-us:
103 Settling time, in microseconds, for voltage increase if the regulator
107 regulator-settling-time-down-us:
110 Settling time, in microseconds, for voltage decrease if the regulator
|
| /Zephyr-latest/dts/bindings/sensor/ |
| D | ti,fdc2x1x.yaml | 200 Channel X Conversion Settling.
202 The FDC will use this settling time to allow the LC sensor to
222 This field defines the Drive Current used during the settling +
|
| /Zephyr-latest/drivers/bluetooth/hci/ |
| D | h4_ifx_cyw43xxx.c | 32 /* BT settling time after power on */
249 /* BT settling time after power on */ in bt_h4_vnd_setup()
|
| /Zephyr-latest/boards/st/st25dv_mb1283_disco/ |
| D | st25dv_mb1283_disco.dts | 156 panel-driver-settling-time-us = <1000>;
|
| /Zephyr-latest/modules/nrf_wifi/bus/ |
| D | rpu_hw_if.c | 233 /* Settling time is 50us (H0) or 100us (L0) */ in rpu_pwron()
242 /* Settling time for iovdd nRF7002 DK/EK - switch (TCK106AG): ~600us */ in rpu_pwron()
|
| /Zephyr-latest/boards/st/stm32f429i_disc1/ |
| D | stm32f429i_disc1.dts | 174 panel-driver-settling-time-us = <1000>;
|
| /Zephyr-latest/soc/nxp/imxrt/imxrt5xx/cm33/ |
| D | soc.c | 35 /* Board System oscillator settling time in us */
243 /* Updated XTAL oscillator settling time */ in rt5xx_clock_init()
|
| /Zephyr-latest/boards/atmel/sam/sam4s_xplained/ |
| D | sam4s_xplained.dts | 189 settling-time = <3>;
|
| /Zephyr-latest/tests/drivers/build_all/input/ |
| D | app.overlay | 224 panel-driver-settling-time-us = <10>;
|
| /Zephyr-latest/doc/develop/api/ |
| D | api_lifecycle.rst | 61 The API is in the process of settling, but has not yet had sufficient real-world
|
| /Zephyr-latest/drivers/sensor/ti/fdc2x1x/ |
| D | fdc2x1x.c | 212 * Set the Conversion Settling value of a specific channel.
215 * @param settle_count - Settling time value.
|
| /Zephyr-latest/drivers/input/ |
| D | input_stmpe811.c | 176 * - bits [0-2] : panel driver settling time in stmpe811_tsc_config_bits()
|
| /Zephyr-latest/subsys/bluetooth/controller/ |
| D | Kconfig.ll_sw_split | 710 radio events to reduce the overall number of crystal settling current
720 higher average current due to increased number of crystal settling
|
| /Zephyr-latest/drivers/video/ |
| D | ov7670.c | 486 /* Reset is active low, has 1ms settling time*/ in ov7670_init()
|
| /Zephyr-latest/drivers/ethernet/phy/ |
| D | phy_realtek_rtl8211f.c | 137 /* Wait another 30 ms (circuits settling time) before accessing registers */ in phy_rt_rtl8211f_reset()
|
| /Zephyr-latest/drivers/ieee802154/ |
| D | ieee802154_cc1200.c | 65 LOG_DBG("Settling"); in cc1200_print_status()
|
| /Zephyr-latest/drivers/sensor/adi/adxl372/ |
| D | adxl372.c | 331 * Set the filter settling period.
|
