Searched full:settings (Results 1 – 25 of 29) sorted by relevance
12
| /hal_nuvoton-3.7.0/m46x/StdDriver/src/ |
| D | ccap.c | 32 … - OUTFMT Image Data Format Output to System Memory. It should be one of the following settings
37 * - PDORD Sensor Input Data Order. It should be one of the following settings
112 * @param[in] u32IntMask Interrupt settings. It could be
131 * @param[in] u32IntMask Interrupt settings. It could be
|
| D | uart.c | 467 …* @details The function is used to configure IrDA relative settings. It consists of TX or …
542 /* Configure IrDA relative settings */ in UART_SelectIrDAMode()
|
| D | ebi.c | 163 …* @param[in] u32TimingConfig Configure EBI timing settings, includes TACC, TAHD, W2X and R2R …
|
| D | scuart.c | 121 * And can use \ref SCUART_SetLineConfig function to update these settings.
|
| D | i2s.c | 114 … The sample rate may not be used from the parameter, it depends on system's clock settings,
|
| D | canfd.c | 379 * @details This function gives user settings to CAN bus timing characteristic.
538 data, then use the nominal settings for both */ in CANFD_CalculateTimingValues()
547 /* calculate data settings */ in CANFD_CalculateTimingValues()
|
| D | qspi.c | 383 …te the actual QSPI bus clock rate according to the QSPIxSEL and DIVIDER settings. Only available i…
|
| /hal_nuvoton-3.7.0/m48x/StdDriver/src/ |
| D | ccap.c | 118 * @param[in] u32IntMask Interrupt settings. It could be
138 * @param[in] u32IntMask Interrupt settings. It could be
159 * @param[in] u32Interface I/O interface settings. It could be
|
| D | uart.c | 458 …* @details The function is used to configure IrDA relative settings. It consists of TX or …
537 /* Configure IrDA relative settings */ in UART_SelectIrDAMode()
|
| D | ebi.c | 163 …* @param[in] u32TimingConfig Configure EBI timing settings, includes TACC, TAHD, W2X and R2R …
|
| D | scuart.c | 102 * And can use \ref SCUART_SetLineConfig function to update these settings
|
| D | i2s.c | 67 … The sample rate may not be used from the parameter, it depends on system's clock settings,
|
| D | can.c | 314 * @details Return current CAN bit rate according to the user bit-timing parameter settings
845 /* check for sjw user settings */ in CAN_SetBaudRate()
|
| D | qspi.c | 387 …te the actual QSPI bus clock rate according to the QSPInSEL and DIVIDER settings. Only available i…
|
| /hal_nuvoton-3.7.0/m46x/Devices/M460/Include/ |
| D | psio_reg.h | 310 …ere are two check points that select the same SLOT, the pin will follow settings of the smaller ch…
323 …ere are two check points that select the same SLOT, the pin will follow settings of the smaller ch…
336 …ere are two check points that select the same SLOT, the pin will follow settings of the smaller ch…
349 …ere are two check points that select the same SLOT, the pin will follow settings of the smaller ch…
362 …ere are two check points that select the same SLOT, the pin will follow settings of the smaller ch…
375 …ere are two check points that select the same SLOT, the pin will follow settings of the smaller ch…
388 …ere are two check points that select the same SLOT, the pin will follow settings of the smaller ch…
402 …ere are two check points that select the same SLOT, the pin will follow settings of the smaller ch…
|
| /hal_nuvoton-3.7.0/zephyr/ |
| D | module.yml | 3 settings:
|
| /hal_nuvoton-3.7.0/m2l31x/StdDriver/src/ |
| D | uart.c | 495 …* @details The function is used to configure IrDA relative settings. It consists of TX or …
587 /* Configure IrDA relative settings */ in UART_SelectIrDAMode()
|
| D | ebi.c | 162 …* @param[in] u32TimingConfig Configure EBI timing settings, includes TACC, TAHD, W2X and R2R …
|
| D | canfd.c | 360 * @details This function gives user settings to CAN bus timing characteristic.
510 data, then use the nominal settings for both */ in CANFD_CalculateTimingValues()
519 /* calculate data settings */ in CANFD_CalculateTimingValues()
|
| D | lpspi.c | 288 …te the actual LPSPI bus clock rate according to the SPInSEL and DIVIDER settings. Only available i…
|
| D | qspi.c | 316 …te the actual QSPI bus clock rate according to the QSPIxSEL and DIVIDER settings. Only available i…
|
| /hal_nuvoton-3.7.0/m48x/Devices/M480/Source/ |
| D | system_M480.c | 89 /* FPU settings ------------------------------------------------------------*/ in SystemInit()
|
| /hal_nuvoton-3.7.0/m46x/Devices/M460/Source/ |
| D | system_M460.c | 75 /* FPU settings ------------------------------------------------------------*/ in SystemInit()
|
| /hal_nuvoton-3.7.0/m46x/StdDriver/inc/ |
| D | ccap.h | 108 * @param[in] u32IntMask interrupt flags settings. It could be
|
| /hal_nuvoton-3.7.0/m48x/StdDriver/inc/ |
| D | ccap.h | 114 * @param[in] u32IntMask interrupt flags settings. It could be
|
12
