Searched full:programming (Results 1 – 25 of 802) sorted by relevance
12345678910>>...33
| /Zephyr-latest/scripts/pylib/pytest-twister-harness/ |
| D | setup.cfg | 14 Programming Language :: Python :: 3.8
15 Programming Language :: Python :: 3.9
16 Programming Language :: Python :: 3.10
17 Programming Language :: Python :: 3.11
|
| /Zephyr-latest/dts/bindings/mtd/ |
| D | renesas,ra-nv-flash.yaml | 12 renesas,programming-enable:
14 description: Enable flash programming configuration
|
| /Zephyr-latest/dts/arm/renesas/ra/ra8/ |
| D | r7fa8m1ahecbd.dtsi | 17 renesas,programming-enable;
25 renesas,programming-enable;
|
| D | r7fa8t1ahecbd.dtsi | 17 renesas,programming-enable;
25 renesas,programming-enable;
|
| D | r7fa8d1bhecbd.dtsi | 18 renesas,programming-enable;
26 renesas,programming-enable;
|
| /Zephyr-latest/boards/nxp/ucans32k1sic/support/ |
| D | startup.cmm | 12 ; program flash by a flash programming routine; if "sram" it *
54 ; Only declares flash, does not execute flash programming
64 ; Switch target flash to reprogramming state, erase virtual flash programming memory,
68 ; Write contents of the file to virtual Flash programming memory
|
| /Zephyr-latest/scripts/west_commands/runners/ |
| D | ecpprog.py | 5 """Runner for the ecpprog programming tool for Lattice FPGAs."""
12 """Runner front-end for programming the FPGA flash at some offset."""
|
| /Zephyr-latest/boards/intel/adsp/doc/ |
| D | intel_adsp_ace15_mtpm.rst | 31 Programming and Debugging
34 Refer to :ref:`intel_adsp_generic` for generic instructions on programming and
|
| D | intel_adsp_cavs25.rst | 28 Programming and Debugging
31 Refer to :ref:`intel_adsp_generic` for generic instructions on programming and
|
| /Zephyr-latest/boards/nxp/mr_canhubk3/support/ |
| D | startup.cmm | 11 ; program flash by a flash programming routine; if "sram" it *
56 ; Only declares flash, does not execute flash programming
71 ; Switch target flash to reprogramming state, erase virtual flash programming memory,
75 ; Write contents of the file to virtual Flash programming memory
|
| /Zephyr-latest/dts/bindings/flash_controller/ |
| D | nxp,iap-fmc553.yaml | 5 NXP (In-Application Programming) flash memory controller for
|
| D | nxp,iap-fmc11.yaml | 5 NXP (In-Application Programming) flash memory controller for the lpc11u6x family.
|
| D | nxp,iap-fmc54.yaml | 5 NXP (In-Application Programming) flash memory controller for the lpc54xxx family.
|
| D | nxp,iap-fmc55.yaml | 5 NXP (In-Application Programming) flash memory controller for
|
| /Zephyr-latest/boards/nordic/thingy53/doc/ |
| D | index.rst | 28 Programming and Debugging
35 programmer is attached to the P9 programming header.
|
| /Zephyr-latest/boards/infineon/cyw920829m2evk_02/doc/ |
| D | index.rst | 25 - USB connector for power, programming and USB-UART bridge
88 Programming and Debugging
91 … onboard programmer/debugger (`KitProg3`_) to provide debugging, flash programming, and serial com…
101 Both the full `ModusToolbox`_ and the `ModusToolbox Programming Tools`_ packages include Infineon O…
103 …g3. This is handled automatically by the ModusToolbox and ModusToolbox Programming Tools installat…
151 .. _ModusToolbox Programming Tools:
|
| /Zephyr-latest/boards/ezurio/bt510/doc/ |
| D | bt510.rst | 116 Programming and Debugging
156 Ezurio provide the USB-SWD programming board (750-03239) that supports
163 To connect the BT510 board for programming or debugging using the USB-SWD programming
164 board, on the programming board set SW6 to the supply out position and SW5 to the 3V3
170 :alt: Sentrius BT510 Sensor connected to programming board
172 Sentrius BT510 Sensor connected to programming board
187 for a suitable driver IC. The USB-SWD programming board has an in-built UART connected
248 …mmer product page: https://www.ezurio.com/wireless-modules/programming-kits/usb-swd-programming-kit
|
| /Zephyr-latest/soc/altr/zephyr_nios2f/cpu/ |
| D | ghrd_10m50da.qpf | 7 # (including device programming or simulation files), and any
13 # that your use is for the sole purpose of programming logic
|
| /Zephyr-latest/soc/nxp/lpc/lpc11u6x/ |
| D | iap.h | 10 * The IAP (In-Application Programming) commands are located in the boot ROM
14 * chapter 27: LPC11U6x/E6x Flash/EEPROM ISP/IAP programming.
|
| /Zephyr-latest/boards/gd/gd32f350r_eval/doc/ |
| D | index.rst | 68 Programming and Debugging
71 Before programming your board make sure to configure boot and serial jumpers as follows:
80 allows flash programming and debugging over USB. There is also a SWD header
|
| /Zephyr-latest/boards/gd/gd32f450v_start/doc/ |
| D | index.rst | 70 Programming and Debugging
73 Before programming your board make sure to configure boot jumpers as
82 allows flash programming and debugging over USB. There is also a SWD header
|
| /Zephyr-latest/boards/gd/gd32vf103c_starter/doc/ |
| D | index.rst | 63 Programming and Debugging
66 Before programming your board make sure to configure boot and serial jumpers
76 allows flash programming and debugging over USB. There is also a JTAG header
|
| /Zephyr-latest/boards/microchip/mpfs_icicle/doc/ |
| D | index.rst | 10 Programming and debugging
37 <https://www.microchip.com/en-us/products/fpgas-and-plds/fpga-and-soc-design-tools/programming-and-…
|
| /Zephyr-latest/boards/gd/gd32vf103v_eval/doc/ |
| D | index.rst | 73 Programming and Debugging
76 Before programming your board make sure to configure boot and serial jumpers
86 allows flash programming and debugging over USB. There is also a JTAG header
|
| /Zephyr-latest/drivers/dai/intel/alh/ |
| D | Kconfig.alh | 23 Select this to enable programming HW ownership
|
12345678910>>...33
