Searched full:pb4 (Results 1 – 25 of 48) sorted by relevance
12
| /Zephyr-latest/dts/bindings/pinctrl/ |
| D | st,stm32f1-pinctrl.yaml | 34 Releases: PB4.
36 Releases: PA15 PB3 PB4.
38 Releases: PA13 PA14 PA15 PB3 PB4.
|
| /Zephyr-latest/boards/weact/stm32g431_core/doc/ |
| D | index.rst | 12 PB4 respectively. Dead battery support requires PA9 and PA10 to be routed to CC1 and
19 After these modifications have been made, PA9, PA10, PB2, PB4, and PB6 should be
40 - UCPD1 CCx : PB6/PB4 (not connected by default)
58 | SB6/SB7 | Open | Connect PB4/PB6 (UCPD1_CCx) to USB-C CCx pins |
60 | SB3/SB5 | Open | Connect PA9/PA10 (UCPD1_DBCCx) to PB6/PB4 |
|
| /Zephyr-latest/boards/gardena/sgrm/doc/ |
| D | index.rst | 53 | PB4.0 | LED red (O) | Mirrors PB0.4 |
55 | PB4.1 | LED green (O) | Mirrors PB0.5 |
57 | PB4.2 | LED blue (O) | Mirrors PB0.6 |
|
| /Zephyr-latest/soc/atmel/sam/samx7x/ |
| D | soc_config.c | 36 /* Disable TDI function on PB4 pin, this is controlled by Bus Matrix in atmel_samx7x_config()
|
| /Zephyr-latest/boards/telink/tlsr9518adk80d/ |
| D | tlsr9518adk80d-pinctrl.dtsi | 33 /* PWM Channel 0 (PB4) */
|
| /Zephyr-latest/drivers/pinctrl/ |
| D | pinctrl_stm32.c | 135 /* releases: PB4 */ in stm32f1_swj_cfg_init()
139 /* releases: PB4 PB3 PA15 */ in stm32f1_swj_cfg_init()
143 /* releases: PB4 PB3 PA13 PA14 PA15 */ in stm32f1_swj_cfg_init()
|
| /Zephyr-latest/boards/adafruit/feather_stm32f405/doc/ |
| D | index.rst | 61 SPI1 uses SCK (PB3), MI (PB4), MO (PB5) and SS (PA15) pins and is
|
| /Zephyr-latest/boards/telink/tlsr9518adk80d/doc/ |
| D | index.rst | 87 - LED0 (blue): PB4, LED1 (green): PB5, LED2 (white): PB6, LED3 (red): PB7
95 - PWM Channel 0: PB4
|
| /Zephyr-latest/boards/st/nucleo_wba52cg/doc/ |
| D | nucleo_wba52cg.rst | 168 - LD1 : PB4
170 - SPI_1_SCK : PB4 (arduino_spi)
|
| /Zephyr-latest/boards/st/nucleo_wba55cg/doc/ |
| D | nucleo_wba55cg.rst | 177 - LD1 : PB4
179 - SPI_1_SCK : PB4 (arduino_spi)
|
| /Zephyr-latest/boards/vcc-gnd/yd_stm32h750vb/doc/ |
| D | index.rst | 32 - LED_4 : PB4
|
| /Zephyr-latest/boards/st/steval_fcu001v1/doc/ |
| D | index.rst | 51 - LD2 : PB4
|
| /Zephyr-latest/boards/st/nucleo_wb05kz/doc/ |
| D | index.rst | 58 - LED (LD2/GREEN) : PB4
|
| /Zephyr-latest/boards/st/nucleo_wb09ke/doc/ |
| D | index.rst | 58 - LED (LD2/GREEN) : PB4
|
| /Zephyr-latest/boards/st/nucleo_wb07cc/doc/ |
| D | index.rst | 58 - LED (LD2/GREEN) : PB4
|
| /Zephyr-latest/boards/st/b_g474e_dpow1/doc/ |
| D | index.rst | 71 - UCPD CC2 : PB4
|
| /Zephyr-latest/boards/weact/blackpill_f401ce/doc/ |
| D | index.rst | 64 change for V2.0 specifically where MISO was routed to PB4 for the flash footprint.
|
| /Zephyr-latest/boards/weact/blackpill_f411ce/doc/ |
| D | index.rst | 64 change for V2.0 specifically where MISO was routed to PB4 for the flash footprint.
|
| /Zephyr-latest/boards/seeed/lora_e5_dev_board/ |
| D | lora_e5_dev_board.dts | 125 /* PB4 can select RS-485 TX, when J17 (A4) is closed */
|
| /Zephyr-latest/boards/st/nucleo_g031k8/doc/ |
| D | index.rst | 74 - SPI1 SCK/MISO/MOSI : PB3/PB4/PB5 (Arduino SPI)
|
| /Zephyr-latest/boards/st/stm32f723e_disco/doc/ |
| D | index.rst | 80 - SPI1 SCK/MISO/MOSI : PA5/PB4/PB5 (Arduino SPI)
|
| /Zephyr-latest/boards/seco/stm32f3_seco_d23/doc/ |
| D | index.rst | 90 - SPI1_MISO : PB4
|
| /Zephyr-latest/boards/st/stm32f072b_disco/doc/ |
| D | index.rst | 84 - SPI1_MISO : PB4
|
| /Zephyr-latest/boards/others/black_f407ve/doc/ |
| D | index.rst | 128 - SPI1 MISO : PB4
|
| /Zephyr-latest/boards/st/nucleo_f446re/doc/ |
| D | index.rst | 103 - I2C3_SDA : PB4
|
12
