Searched full:normally (Results 1 – 25 of 181) sorted by relevance
12345678
| /Zephyr-Core-3.6.0/subsys/net/ip/ |
| D | Kconfig.ipv6 | 47 The value should normally be > 0. The device receiving the IPv6
57 The value should normally be > 0. The device receiving the IPv6
76 should not cause issues normally as we support anyway the minimum
124 The value depends on your network needs. MLD should normally
133 normally be active.
140 The value depends on your network needs. ND should normally
148 The value depends on your network needs. DAD should normally
|
| D | Kconfig.ipv4 | 19 The value should normally be > 0. The device receiving the IPv4
29 The value should normally be > 0. The device receiving the IPv4
77 The value depends on your network needs. IGMP should normally be
|
| /Zephyr-Core-3.6.0/tests/kernel/fatal/exception/ |
| D | README | 4 thread, the thread gets aborted and the rest of the system executes normally.
|
| /Zephyr-Core-3.6.0/subsys/net/lib/trickle/ |
| D | Kconfig | 9 Normally this is enabled automatically if needed,
|
| /Zephyr-Core-3.6.0/include/zephyr/drivers/can/ |
| D | transceiver.h | 55 * should not normally be controlled by the application.
78 * should not normally be controlled by the application.
|
| /Zephyr-Core-3.6.0/lib/libc/minimal/source/stdlib/ |
| D | qsort.c | 14 * Normally parent is defined parent(k) = floor((k-1) / 2) but we can avoid a
20 * Normally left is defined left(k) = (2 * k + 1) but we can avoid a
27 * Normally right is defined right(k) = (2 * k + 2) but we can avoid a
|
| /Zephyr-Core-3.6.0/drivers/gpio/ |
| D | Kconfig.mmio32 | 11 Zephyr normally expects to be specified using a GPIO pin, e.g. for
|
| /Zephyr-Core-3.6.0/subsys/net/lib/sntp/ |
| D | Kconfig | 19 Enabling this option uses more resources (memory) and is not normally
|
| /Zephyr-Core-3.6.0/drivers/led_strip/ |
| D | Kconfig | 26 # is not normally needed.
|
| /Zephyr-Core-3.6.0/subsys/mgmt/mcumgr/grp/img_mgmt/ |
| D | Kconfig | 70 Normally it should not be allowed to confirm any slots of non-active
80 Normally it should not be allowed to confirm any slots of non-active
98 This changes how "image" is understood by MCUmgr: normally MCUmgr allows uploading to
|
| /Zephyr-Core-3.6.0/include/zephyr/arch/nios2/ |
| D | thread.h | 36 /* Normally used for the frame pointer but also a general purpose
|
| /Zephyr-Core-3.6.0/subsys/sensing/ |
| D | sensing.c | 15 /* sensing_open_sensor is normally called by applications: hid, chre, zephyr main, etc */
64 /* sensing_close_sensor is normally called by applications: hid, chre, zephyr main, etc */
|
| /Zephyr-Core-3.6.0/dts/bindings/can/ |
| D | bosch,m_can-base.yaml | 16 from. This is normally set to 0x0 when using a non-shared message RAM. The remaining cells
|
| /Zephyr-Core-3.6.0/samples/subsys/display/cfb_custom_font/ |
| D | README.rst | 26 Generic config file, normally you should use this.
|
| /Zephyr-Core-3.6.0/boards/posix/nrf_bsim/ |
| D | Kconfig | 5 # The following file is normally parsed only for the ARM architecture, which is
|
| D | Kconfig.defconfig | 72 # simulated board => we disable it by default. With this Openthread will normally
|
| /Zephyr-Core-3.6.0/scripts/native_simulator/common/src/include/ |
| D | nsi_hws_models_if.h | 30 * (Normally HW models will not care about the event ordering, and will simply set a prio like 100)
|
| /Zephyr-Core-3.6.0/drivers/modem/ |
| D | Kconfig.wncm14a2a | 36 for the network connection context. Normally, don't need to change
|
| /Zephyr-Core-3.6.0/soc/posix/inf_clock/ |
| D | soc.c | 77 * Normally called from arch_cpu_idle():
91 /* We are awoken, normally that means some interrupt has just come in posix_halt_cpu()
|
| /Zephyr-Core-3.6.0/include/zephyr/drivers/flash/ |
| D | nrf_qspi_nor.h | 17 * Normally, the driver deactivates the QSPI peripheral for periods when
|
| /Zephyr-Core-3.6.0/dts/arm/gd/gd32l23x/ |
| D | gd32l233rc.dtsi | 38 * From other GD32 DataSheets, we can find 1KB page normally have a
|
| /Zephyr-Core-3.6.0/samples/drivers/uart/echo_bot/ |
| D | README.rst | 18 By default, the UART peripheral that is normally used for the Zephyr shell
|
| /Zephyr-Core-3.6.0/tests/subsys/settings/file/src/ |
| D | settings_test_save_in_file.c | 28 cf.cf_lines = 0; /* normally fetched while loading, but this is test */ in ZTEST()
|
| /Zephyr-Core-3.6.0/dts/bindings/ethernet/ |
| D | atmel,gmac-common.yaml | 28 means that normally gmac will reject any frame above max-frame-size
|
| /Zephyr-Core-3.6.0/dts/bindings/lora/ |
| D | semtech,sx127x-base.yaml | 23 These signals are normally active-high.
|
12345678
