Searched full:noise (Results 1 – 25 of 52) sorted by relevance
123
| /Zephyr-Core-3.6.0/dts/bindings/sensor/ |
| D | invensense,icp10125.yaml | 18 - "low-noise"
19 - "ultra-low-noise"
28 - "low-noise"
29 - "ultra-low-noise"
|
| D | ti,tmag5273.yaml | 142 Enables additional sampling of the sensor data to reduce the noise effect
160 low-noise:
163 Select low-noise mode when enabled, and low-power mode when disabled.
|
| D | st,lis2dw12-common.yaml | 164 low-noise:
168 This influences the noise density and the current consumption.
|
| D | nxp,s32-qdec.yaml | 12 lcu output filters are set to capture maximum speed sensitivity and avoid channel noise.
|
| /Zephyr-Core-3.6.0/dts/bindings/input/ |
| D | espressif,esp32-touch-sensor.yaml | 26 filter-noise-thr = <ESP32_TOUCH_FILTER_NOISE_THR_4_8TH>;
92 filter-noise-thr:
96 Touch sensor noise threshold coefficient.
110 Touch sensor level of filter applied on the original data against large noise interference.
|
| D | st,stmpe811.yaml | 69 is recommended at the touchscreen terminals for noise filtering.
103 Higher values result in more filtering of noise, but also introduce
108 at the cost of less noise filtering.
|
| /Zephyr-Core-3.6.0/tests/posix/pthread_pressure/ |
| D | testcase.yaml | 11 # Enabled for GitHub CI to reduce host scheduling noise while running
|
| /Zephyr-Core-3.6.0/drivers/entropy/ |
| D | Kconfig.esp32 | 15 numbers: noise from these radios are used to feed entropy in this
|
| D | Kconfig.nrf5 | 22 generator, based on internal thermal noise, that provides a
|
| D | Kconfig.stm32 | 14 generator, based on a continuous analog noise, that provides
|
| /Zephyr-Core-3.6.0/dts/bindings/rng/ |
| D | espressif,esp32-trng.yaml | 7 The TRNG uses the noise in the Wi-Fi/BT RF system. When Wi-Fi and BT are
|
| /Zephyr-Core-3.6.0/dts/bindings/pinctrl/ |
| D | gd,gd32-afio.yaml | 23 output speed is greater than 50MHz to reduce the I/O noise effects on
|
| D | nxp,lpc-iocon-pinctrl.yaml | 113 Digital input filter. Noise pulses below 10ms are filtered out.
|
| /Zephyr-Core-3.6.0/include/zephyr/dt-bindings/input/ |
| D | esp32-touch-sensor-input.h | 22 /* Touch sensor level of filter noise threshold coefficient*/
|
| /Zephyr-Core-3.6.0/drivers/sensor/ina23x/ |
| D | Kconfig | 37 looking at measurement noise or debugging the SHUNT_CAL value.
|
| /Zephyr-Core-3.6.0/drivers/sensor/sht3xd/ |
| D | Kconfig | 60 noise level and energy consumption.
|
| /Zephyr-Core-3.6.0/samples/sensor/fdc2x1x/ |
| D | README.rst | 21 noise susceptibility of the sensors. With the FDC2x1x innovative EMI resistant
22 architecture, performance can be maintained even in presence of high-noise environments.
|
| /Zephyr-Core-3.6.0/samples/boards/nrf/mesh/onoff-app/ |
| D | prj.conf | 1 #CONFIG_INIT_STACKS=y # if set, lots of noise from mesh/adv.c: STACK_ANALYZE
|
| /Zephyr-Core-3.6.0/dts/bindings/net/wireless/ |
| D | generic-fem-two-ctrl-pins.yaml | 12 The CRX control pin is used to enable the Low Noise Amplifier
|
| /Zephyr-Core-3.6.0/dts/bindings/display/ |
| D | ftdi,ft800.yaml | 39 which helps reduce the system noise.
|
| /Zephyr-Core-3.6.0/tests/posix/common/src/ |
| D | clock.c | 171 * Note: we do not want to assert any individual samples due to scheduler noise. in ZTEST()
172 * The CMA filters out the noise so we can make an assertion (on average). in ZTEST()
|
| /Zephyr-Core-3.6.0/boards/xtensa/esp32s2_saola/ |
| D | esp32s2_saola.dts | 68 filter-noise-thr = <ESP32_TOUCH_FILTER_NOISE_THR_4_8TH>;
|
| /Zephyr-Core-3.6.0/samples/modules/tflite-micro/magic_wand/train/ |
| D | data_augmentation.py | 56 # Random noise
|
| /Zephyr-Core-3.6.0/include/zephyr/bluetooth/ |
| D | a2dp-codec.h | 72 #define A2DP_SBC_ALLOC_MTHD_LOUDNESS BIT(0) /**< Allocate based on the signal-to-noise ratio */
|
| /Zephyr-Core-3.6.0/boards/xtensa/esp32s3_devkitm/ |
| D | esp32s3_devkitm.dts | 79 filter-noise-thr = <ESP32_TOUCH_FILTER_NOISE_THR_4_8TH>;
|
123
