Searched full:necessary (Results 1 – 25 of 554) sorted by relevance
12345678910>>...23
| /Zephyr-Core-3.6.0/drivers/sensor/icm42688/ |
| D | icm42688_spi.h | 16 * this functions wraps all logic necessary to write to any of the ICM42688 registers, regardless
29 * this functions wraps all logic necessary to update any of the ICM42688 registers, regardless
44 * this functions wraps all logic necessary to read from any of the ICM42688 registers, regardless
|
| /Zephyr-Core-3.6.0/drivers/sensor/icm42670/ |
| D | icm42670_spi.h | 17 * this functions wraps all logic necessary to write to any of the ICM42670 registers, regardless
30 * this functions wraps all logic necessary to update any of the ICM42670 registers, regardless
45 * this functions wraps all logic necessary to read from any of the ICM42670 registers, regardless
|
| /Zephyr-Core-3.6.0/doc/services/modem/ |
| D | index.rst | 6 This service provides modules necessary to communicate with modems.
9 software necessary to perform RF (Radio-Frequency) communication,
|
| /Zephyr-Core-3.6.0/subsys/dfu/ |
| D | Kconfig | 73 If enabled, flash is erased as necessary when receiving new firmware,
74 instead of erasing the whole image slot at once. This is necessary
|
| /Zephyr-Core-3.6.0/soc/arm/ti_simplelink/cc13x2_cc26x2/ |
| D | soc.c | 14 /* Performs necessary trim of the device. */ in ti_cc13x2_cc26x2_init()
|
| /Zephyr-Core-3.6.0/soc/arm/ti_simplelink/cc13x2x7_cc26x2x7/ |
| D | soc.c | 14 /* Performs necessary trim of the device. */ in ti_cc13x7_cc26x7_init()
|
| /Zephyr-Core-3.6.0/drivers/i2c/ |
| D | Kconfig.mcux | 12 i.e. it should wait as long as necessary.
|
| /Zephyr-Core-3.6.0/samples/bluetooth/hci_ipc/ |
| D | prj.conf | 19 # Enable and adjust the below value as necessary
|
| /Zephyr-Core-3.6.0/tests/kernel/usage/thread_runtime_stats/ |
| D | testcase.yaml | 7 # The following architectures are exluded as the necessary
|
| /Zephyr-Core-3.6.0/subsys/bluetooth/controller/ll_sw/openisa/hal/ |
| D | cpu.h | 17 /* FIXME: Add necessary host machine required Data Memory Barrier in cpu_dmb()
|
| /Zephyr-Core-3.6.0/samples/basic/blinky_pwm/ |
| D | README.rst | 34 No additional wiring is necessary if ``pwm_led0`` refers to hardware that is
37 In these other cases, however, manual wiring is necessary:
|
| /Zephyr-Core-3.6.0/boards/shields/rk055hdmipi4m/ |
| D | Kconfig.defconfig | 32 # display refreshes, which is not necessary for the eLCDIF driver
|
| /Zephyr-Core-3.6.0/samples/subsys/usb/uac2_explicit_feedback/ |
| D | README.rst | 34 neither subsystem provides the necessary timestamp information.
50 no extra connections are necessary and the sample can even be used without any
|
| /Zephyr-Core-3.6.0/lib/libc/minimal/ |
| D | Kconfig | 77 necessary to set CONFIG_MINIMAL_LIBC_NON_REENTRANT_FUNCTIONS=y.
89 In order to make use of the non-reentrant gmtime(), it is necessary
|
| /Zephyr-Core-3.6.0/samples/boards/esp32/light_sleep/ |
| D | README.rst | 68 check DTR/RTS configuration in the serial monitor. This is not necessary for
69 IDF monitor, but for other tools it might be necessary to set DTR and RTS line
|
| /Zephyr-Core-3.6.0/subsys/testsuite/include/zephyr/ |
| D | timestamp.h | 30 /* time necessary to read the time */
66 * if benchmarking code took less time than necessary for the
|
| /Zephyr-Core-3.6.0/boards/arc/iotdk/ |
| D | Kconfig.board | 10 …The DesignWare ARC IoT Development Kit board is a versatile platform that includes the necessary h…
|
| /Zephyr-Core-3.6.0/boards/shields/rk055hdmipi4ma0/ |
| D | Kconfig.defconfig | 34 # display refreshes, which is not necessary for the eLCDIF driver
|
| /Zephyr-Core-3.6.0/include/zephyr/dt-bindings/ |
| D | dt-util.h | 15 * necessary background to elaborate complex constructions like
|
| /Zephyr-Core-3.6.0/tests/kernel/timer/cycle64/ |
| D | testcase.yaml | 11 # timeout as necessary.
|
| /Zephyr-Core-3.6.0/dts/bindings/sensor/ |
| D | sensirion,shtcx.yaml | 15 Specifies which chip exactly is used. This is necessary to get exact
|
| /Zephyr-Core-3.6.0/doc/connectivity/networking/ |
| D | networking_with_host.rst | 19 While developing networking software, it is usually necessary to connect and
28 use it only when necessary. See :ref:`networking_with_qemu` for details.
|
| /Zephyr-Core-3.6.0/include/zephyr/timing/ |
| D | timing.h | 35 * Implements the necessary bits to support timing measurement
44 * Perform the necessary steps to initialize the timing subsystem.
151 * Implements the necessary bits to support timing measurement
160 * Perform the necessary steps to initialize the timing subsystem.
272 * Perform the necessary steps to initialize the timing subsystem.
|
| /Zephyr-Core-3.6.0/boards/arm/nrf52840_mdk_usb_dongle/ |
| D | Kconfig.defconfig | 23 # so no override is necessary.
|
| /Zephyr-Core-3.6.0/dts/bindings/base/ |
| D | pm.yaml | 17 the system) by default but they can be enabled at runtime if necessary.
|
12345678910>>...23
