Searched full:measuring (Results 1 – 25 of 29) sorted by relevance
12
| /Zephyr-latest/dts/bindings/sensor/ |
| D | adi,adltc2990.yaml | 66 description: Define the resistor to be used for measuring current in microohms
70 description: Define the resistor to be used for measuring Vout in milliohms
74 description: Define the resistor to be used for measuring Vout in milliohms
78 description: Define the resistor to be used for measuring current in microohms
82 description: Define the resistor to be used for measuring Vout in milliohms
86 description: Define the resistor to be used for measuring Vout in milliohms
|
| D | plantower,pms7003.yaml | 6 Air pollution sensor capable of measuring mass concentration of dust. See
|
| D | ti,tmp112.yaml | 23 description: When true use 13-bit data format allowing measuring temperature up to 128°C
|
| D | st,stm32-temp-cal-common.yaml | 30 ADC resolution used for measuring calibration data
|
| D | maxim,max31875.yaml | 32 When true, use 13-bit data format to allow for measuring
|
| /Zephyr-latest/dts/bindings/tcpc/ |
| D | nuvoton,numaker-tcpc.yaml | 138 EADC channels for measuring VBUS/VCONN voltage
144 "chn-vbus": EADC channel for measuring VBUS voltage (option)
145 "chn-vconn": EADC channel for measuring VCONN voltage (option)
|
| /Zephyr-latest/tests/benchmarks/latency_measure/src/ |
| D | thread.c | 40 /* 3. Finish measuring time to start <alt_thread> */ in alt_thread_entry()
48 /* 7. Begin measuring time to suspend active thread (self/alt_thread) */ in alt_thread_entry()
53 /* 10. Finish measuring time to resume <alt_thread> (self) */ in alt_thread_entry()
118 /* 2. Begin measuring time to start <alt_thread> */ in start_thread_entry()
132 /* 8. Finish measuring time to suspend <alt_thread> */ in start_thread_entry()
138 /* 9. Being measuring time to resume <alt_thread> */ in start_thread_entry()
|
| /Zephyr-latest/doc/hardware/peripherals/sensor/ |
| D | channels.rst | 13 enable measuring many readings of perhaps temperature, light intensity, amperage,
|
| /Zephyr-latest/drivers/sensor/st/lis2dh/ |
| D | Kconfig | 156 The temperature sensor is most suitable for measuring
|
| /Zephyr-latest/samples/basic/minimal/ |
| D | README.rst | 21 Building and measuring ROM size
|
| /Zephyr-latest/subsys/testsuite/include/zephyr/ |
| D | timestamp.h | 8 * @file macroses for measuring time in benchmarking tests
|
| /Zephyr-latest/drivers/sensor/ams/ens210/ |
| D | ens210.c | 56 /* Start measuring */ in ens210_measure()
329 /* Start measuring */ in ens210_init()
|
| /Zephyr-latest/tests/kernel/mem_protect/demand_paging/mem_map/src/ |
| D | main.c | 241 * are measuring stuff in test_k_mem_page_out()
270 * are measuring stuff in ZTEST()
|
| /Zephyr-latest/samples/kernel/metairq_dispatch/ |
| D | README.rst | 61 Note that because the test is fundamentally measuring thread
|
| /Zephyr-latest/boards/st/stm32l1_disco/doc/ |
| D | index.rst | 9 Support circuitry for measuring power consumption is also available.
|
| /Zephyr-latest/boards/norik/octopus_io_board/doc/ |
| D | index.rst | 84 The board also has multiple built-in test points for measuring current consumption of the board, wh…
|
| /Zephyr-latest/boards/renesas/ek_ra6m1/doc/ |
| D | index.rst | 42 - One jumper to allow measuring of Main MCU current
|
| /Zephyr-latest/include/zephyr/sys/ |
| D | sys_heap.h | 91 * Set the statistic measuring the maximum number of allocated bytes to the
|
| /Zephyr-latest/drivers/usb_c/tcpc/ |
| D | ucpd_numaker.c | 222 /* Trigger source for measuring VBUS/VCONN voltage */
1446 * @brief Initializes EADC to be timer-triggered for measuring
1468 /* Configure sample module for measuring VBUS voltage in numaker_eadc_init_startup()
1482 /* Configure sample module for measuring VCONN voltage in numaker_eadc_init_startup()
1500 * @brief Initializes Timer to trigger EADC for measuring VBUS/VCONN
|
| /Zephyr-latest/doc/kernel/ |
| D | timeutil.rst | 58 routines. For example, ``time_t`` measuring seconds since the POSIX EPOCH is
|
| /Zephyr-latest/tests/bsim/bluetooth/mesh/src/ |
| D | test_access.c | 723 /* Receive a periodically published message and check publication period by measuring interval
821 /* Receive a published message and check retransmission interval by measuring interval between
|
| /Zephyr-latest/subsys/net/l2/ethernet/gptp/ |
| D | gptp_data_set.h | 457 /** The port is measuring the path delay. */
|
| /Zephyr-latest/drivers/sensor/vishay/veml7700/ |
| D | veml7700.c | 116 * measuring mode. In this mode the sensor measures on demand an
|
| /Zephyr-latest/subsys/net/lib/shell/ |
| D | gptp.c | 319 PR("The port is measuring the path delay " in gptp_print_port_info()
|
| /Zephyr-latest/drivers/usb/common/nrf_usbd_common/ |
| D | nrf_usbd_common.h | 387 * The hardware starts measuring time when wake up is possible.
|
12
