Home
last modified time | relevance | path

Searched full:ina237 (Results 1 – 15 of 15) sorted by relevance

/Zephyr-latest/tests/drivers/sensor/ina237/boards/
Dnative_sim.overlay5 #include <zephyr/dt-bindings/sensor/ina237.h>
11 ina237_default_test: ina237@40 {
12 compatible = "ti,ina237";
20 ina237@41 {
21 compatible = "ti,ina237";
30 ina237@42 {
31 compatible = "ti,ina237";
40 ina237@43 {
41 compatible = "ti,ina237";
/Zephyr-latest/drivers/sensor/ti/ina23x/
DKconfig22 config INA237 config
23 bool "INA237"
27 Enable driver for INA237.
30 bool "INA237 VShunt Measurement Enable"
33 Enable shunt voltage measurement for INA237.
36 INA237 based upon the SHUNT_CAL register. This value is useful for
DCMakeLists.txt7 zephyr_library_sources_ifdef(CONFIG_INA237 ina237.c)
Dina237.c9 #include "ina237.h"
14 #include <zephyr/dt-bindings/sensor/ina237.h>
17 LOG_MODULE_REGISTER(INA237, CONFIG_SENSOR_LOG_LEVEL);
233 LOG_ERR("INA237 attribute not supported."); in ina237_attr_set()
259 LOG_ERR("INA237 attribute not supported."); in ina237_attr_get()
379 struct ina237_data *ina237 = dev->data; in ina237_trigger_set() local
385 ina237->trigger.handler_alert = handler; in ina237_trigger_set()
386 ina237->trigger.trig_alert = trig; in ina237_trigger_set()
/Zephyr-latest/dts/bindings/sensor/
Dti,ina237.yaml8 TI INA237 Bidirectional Current and Power Monitor.
9 The <zephyr/dt-bindings/sensor/ina237.h> file should be included in the
13 compatible: "ti,ina237"
27 for INA237.
/Zephyr-latest/tests/drivers/sensor/ina237/
Dtestcase.yaml5 drivers.sensor.ina237:
/Zephyr-latest/tests/drivers/sensor/ina237/src/
Dina237_emul.h6 * Emulator for the TI INA237 I2C power monitor
Dina237_test.c11 #include <zephyr/dt-bindings/sensor/ina237.h>
15 #include <ina237.h>
44 * @brief Verify bus voltages for all ina237 nodes in DT
245 /* Create a test fixture for each enabled ina237 device node */
260 /* Create a test suite for each enabled ina237 device node */
Dina237_emul.c6 * Emulator for the TI INA237 I2C power monitor
16 #include <ina237.h>
76 /* The INA237 uses big-endian read 16, read 24, and write 16 transactions */ in ina237_emul_transfer_i2c()
/Zephyr-latest/include/zephyr/dt-bindings/sensor/
Dina237.h63 * @brief Macro for creating the INA237 configuration value
76 * @brief Macro for creating the INA237 ADC configuration value
/Zephyr-latest/tests/drivers/build_all/sensor/
Di2c.dtsi617 test_i2c_ina237: ina237@5a {
618 compatible = "ti,ina237";
/Zephyr-latest/doc/releases/
Drelease-notes-3.0.rst595 * Refactored INA230 driver to add support for INA237 variant.
749 Instead, use :dtcompatible:`ti,ina230` or :dtcompatible:`ti,ina237`.
Drelease-notes-3.2.rst748 * Enhanced the INA237 driver to support triggered mode.
1299 * :dtcompatible:`ti,ina237`: new ``alert-config``, ``irq-gpios`` properties.
Drelease-notes-3.5.rst1942 * :dtcompatible:`ti,ina237` (on i2c bus):
Drelease-notes-3.3.rst1955 - :dtcompatible:`ti,ina237` (on i2c bus):