Searched full:hand (Results 1 – 25 of 48) sorted by relevance
12
| /Zephyr-Core-3.5.0/dts/bindings/gpio/ |
| D | atmel-xplained-pro-header.yaml | 14 * PWR is right angled at the top right hand side of the board. This
16 * EXT1 is right angled at the top right hand side of the board, located
18 * EXT2 is right angled and at the bottom right hand side of the board.
|
| /Zephyr-Core-3.5.0/doc/develop/toolchains/ |
| D | cadence_xcc.rst | 7 on hand. This usually contains two parts:
14 * This add-on allows the compiler to generate code for the SoC on hand.
|
| /Zephyr-Core-3.5.0/include/zephyr/dt-bindings/usb/ |
| D | usb.h | 11 * the generation point of view, so for now we just hand code the enum. This
|
| /Zephyr-Core-3.5.0/tests/bsim/bluetooth/ |
| D | compile.sh | 24 # On the other hand the audio compile script, only builds one image. So we parallelize it with
|
| /Zephyr-Core-3.5.0/doc/templates/ |
| D | sample.tmpl | 31 hand-written code-block.]
|
| /Zephyr-Core-3.5.0/include/zephyr/drivers/misc/ft8xx/ |
| D | ft8xx_copro.h | 55 * only seconds hand is drawn
60 /** Co-processor clock widget is drawn without seconds hand */
|
| /Zephyr-Core-3.5.0/arch/xtensa/core/ |
| D | cpu_idle.c | 12 * This function is simply enough and full of hand written
|
| /Zephyr-Core-3.5.0/samples/subsys/portability/cmsis_rtos_v1/philosophers/src/ |
| D | phil_obj_abstract.h | 26 * When using static objects, references to each object must be put by hand in
|
| /Zephyr-Core-3.5.0/.github/ISSUE_TEMPLATE/ |
| D | 007_ext-source.md | 40 component to solve the problem at hand (there may be a better options
|
| /Zephyr-Core-3.5.0/samples/subsys/portability/cmsis_rtos_v2/philosophers/src/ |
| D | phil_obj_abstract.h | 26 * When using static objects, references to each object must be put by hand in
|
| /Zephyr-Core-3.5.0/tests/bsim/bluetooth/ll/edtt/ |
| D | README.txt | 49 hand the BabbleSim 2G4 Phy, EDTT bridge, EDTT and needed simulated devices.
|
| /Zephyr-Core-3.5.0/boards/arm64/xenvm/doc/ |
| D | index.rst | 76 environment. On other hand, Zephyr uses static configuration that should be know
162 guest will parse device tree in runtime. On other hand, Zephyr supports only
|
| /Zephyr-Core-3.5.0/tests/subsys/mgmt/mcumgr/smp_reassembly/src/ |
| D | main.c | 75 /* This will normally be done by packet processing and should not be done by hand: in ZTEST()
157 /* This will normally be done by packet processing and should not be done by hand: in ZTEST()
|
| /Zephyr-Core-3.5.0/doc/build/dts/ |
| D | design.rst | 43 generated and maintained by hand. This can and should be obtained from the
|
| /Zephyr-Core-3.5.0/tests/drivers/gpio/gpio_basic_api/src/ |
| D | test_gpio_port.c | 14 /* Short-hand for a checked read of PIN_IN raw state */
25 /* Short-hand for a checked read of PIN_IN logical state */
36 /* Short-hand for a checked write of PIN_OUT raw state */
50 /* Short-hand for a checked write of PIN_OUT logic state */
|
| /Zephyr-Core-3.5.0/doc/safety/ |
| D | safety_overview.rst | 136 very important in terms of safety. On the one hand, this specifies and describes in detail and on a
137 technical level what the software should do, and on the other hand, it is an important and
140 and tracing in hand, it can now be verified whether the functionality has been tested and
|
| /Zephyr-Core-3.5.0/soc/xtensa/espressif_esp32/esp32/ |
| D | esp32-mp.c | 52 * use of k_busy_wait() (and even hand-crafted timer loops using the
209 * use of k_busy_wait() (and even hand-crafted timer loops using the in esp_appcpu_start()
|
| /Zephyr-Core-3.5.0/drivers/clock_control/ |
| D | clock_control_agilex5_ll.c | 51 * hand-off data. in get_ref_clk()
|
| /Zephyr-Core-3.5.0/include/zephyr/sys/ |
| D | iterable_sections.h | 72 * This allows the macro to hand different types as well as cases where the
86 * This allows the macro to hand different types as well as cases where the
|
| /Zephyr-Core-3.5.0/doc/develop/west/ |
| D | without-west.rst | 8 particular, you will have to do work "by hand" to replace these
|
| /Zephyr-Core-3.5.0/drivers/modem/ |
| D | Kconfig | 126 incoming data and hand it back to the modem driver via callbacks
|
| /Zephyr-Core-3.5.0/samples/philosophers/src/ |
| D | phil_obj_abstract.h | 26 * When using static objects, references to each object must be put by hand in
|
| /Zephyr-Core-3.5.0/doc/connectivity/networking/api/ |
| D | mqtt_sn.rst | 117 function periodically to process incoming data. Connection upkeep, on the other hand,
|
| /Zephyr-Core-3.5.0/doc/build/kconfig/ |
| D | menuconfig.rst | 14 the application build directory by hand. Using one of the configuration
|
| /Zephyr-Core-3.5.0/include/zephyr/sip_svc/ |
| D | sip_svc.h | 33 * successfully open the channel. On the other hand, it
|
12
