Searched full:even (Results 1 – 25 of 685) sorted by relevance
12345678910>>...28
| /Zephyr-latest/dts/bindings/serial/ |
| D | uart-controller.yaml | 21 and 2 for even parity. Default to none if not specified.
25 - "even"
|
| /Zephyr-latest/tests/bsim/bluetooth/host/gatt/ccc_store/ |
| D | overlay-no_store_on_write.conf | 1 # Test that CCC is stored even if BT_SETTINGS_DELAYED_STORE is enabled
|
| /Zephyr-latest/soc/native/inf_clock/ |
| D | Kconfig | 36 the first one to boot, or even that it will boot automatically.
52 even if in other circumstances this MCU would not start automatically (for ex. because
|
| /Zephyr-latest/scripts/tests/twister_blackbox/test_data/tests/dummy/agnostic/group2/ |
| D | test_data.yaml | 11 - even
|
| /Zephyr-latest/scripts/tests/twister_blackbox/test_data/tests/dummy/agnostic/group1/subgroup2/ |
| D | test_data.yaml | 13 - even
|
| /Zephyr-latest/dts/bindings/display/ |
| D | solomon,ssd1322.yaml | 50 remap-com-odd-even-split:
52 description: Odd even split of COM pins.
|
| /Zephyr-latest/tests/posix/single_process/ |
| D | prj.conf | 4 # Let's explicitly choose PICOLIBC, so it is used if supported even if it would not have been the
|
| /Zephyr-latest/arch/arm/core/cortex_m/ |
| D | thread_abort.c | 33 * even for non-peripheral interrupts, even though in z_impl_k_thread_abort()
|
| /Zephyr-latest/tests/drivers/gpio/gpio_basic_api/ |
| D | Kconfig | 7 bool "Skip the pull test even if the driver supports it"
|
| /Zephyr-latest/samples/drivers/i2s/i2s_codec/boards/ |
| D | stm32f4_disco.conf | 4 # Even though the stm32f4_disco board overlay is tuned for 22.05/44.1/88.2kHz
|
| /Zephyr-latest/boards/shields/nrf7002eb/boards/ |
| D | nrf54h20dk_nrf54h20_cpuapp.overlay | 9 * The external SR RF switch may not even be present on this board.
|
| /Zephyr-latest/tests/subsys/logging/log_blocking/ |
| D | testcase.yaml | 23 # twister fails with "unexpected eof" even though the test passes
|
| /Zephyr-latest/boards/arduino/opta/support/ |
| D | openocd_opta_stm32h747xx_m7.cfg | 9 # even when core is in sleep mode
|
| /Zephyr-latest/boards/arduino/nicla_vision/support/ |
| D | openocd_arduino_nicla_vision_m7.cfg | 9 # even when core is in sleep mode
|
| /Zephyr-latest/boards/st/stm32h747i_disco/support/ |
| D | openocd_stm32h747i_disco_m7.cfg | 9 # even when core is in sleep mode
|
| /Zephyr-latest/boards/arduino/giga_r1/support/ |
| D | openocd_arduino_giga_r1_m7.cfg | 9 # even when core is in sleep mode
|
| /Zephyr-latest/boards/st/stm32h735g_disco/support/ |
| D | openocd.cfg | 11 # even when core is in sleep mode
|
| /Zephyr-latest/boards/st/stm32h750b_dk/support/ |
| D | openocd.cfg | 11 # even when core is in sleep mode
|
| /Zephyr-latest/boards/vcc-gnd/yd_stm32h750vb/support/ |
| D | openocd.cfg | 11 # even when core is in sleep mode
|
| /Zephyr-latest/boards/st/nucleo_h7a3zi_q/support/ |
| D | openocd.cfg | 11 # even when core is in sleep mode
|
| /Zephyr-latest/soc/espressif/common/ |
| D | Kconfig.esptool | 18 1. If the flash chip is an Octal one, even if one of "QIO", "QOUT", "DIO", "DOUT" options is
21 …2. If the flash chip is a Quad one, even if "OPI" is selected in `ESPTOOLPY_FLASHMODE`, our code w…
123 # On some of the ESP chips, max boot frequency would be equal to (or even lower than) 80m.
|
| /Zephyr-latest/soc/st/stm32/stm32wb0x/ |
| D | ram_sections.ld | 11 * SRAM0 unused, even though it could store data.
|
| /Zephyr-latest/dts/arm/st/f4/ |
| D | stm32f429vX.dtsi | 7 * Don't remove this file even if none of the SoCs currently
|
| /Zephyr-latest/samples/arch/mpu/mpu_test/ |
| D | prj.conf | 6 ### needs to be enabled to even enable CONFIG_FLASH, as the probe needs
|
| /Zephyr-latest/boards/st/nucleo_h745zi_q/support/ |
| D | openocd.cfg | 10 # even when core is in sleep mode
|
12345678910>>...28
