Home
last modified time | relevance | path

Searched full:enabling (Results 1 – 25 of 495) sorted by relevance

12345678910>>...20

/Zephyr-Core-3.6.0/subsys/bluetooth/audio/
DKconfig.cap17 Enabling this will enable the CAP Acceptor role. This instantiates the
26 Enabling this will allow a CAP acceptor to be a set member.
27 Enabling this will require a manual register of the CAS service.
28 Enabling will take one of the allocated CSIS instances
40 Enabling this will enable the CAP Initiator role.
53 Enabling this will enable the CAP Initiator role.
DKconfig.pbp12 Enabling this will enable PBP.
/Zephyr-Core-3.6.0/drivers/flash/
DKconfig.stm3230 Enables flash extended operation for enabling/disabling flash write
47 Enables flash extended operation for enabling/disabling flash readout
59 bool "Allow enabling readout protection permanently"
/Zephyr-Core-3.6.0/drivers/serial/
DKconfig.altera22 Before enabling this, please try to optimise the ISR to fetch the receive data faster.
23 Enabling this will cause the transmitter to wait for rising edge of CTS before sending.
/Zephyr-Core-3.6.0/subsys/stats/
DKconfig18 form "s0", "s1", etc. Enabling this setting simplifies debugging,
28 form "s0", "s1", etc. Enabling this setting simplifies debugging,
/Zephyr-Core-3.6.0/tests/bluetooth/df/connectionless_cte_chains/src/
Dtest_add_cte_to_chain.c65 "Unexpected error while enabling CTE for periodic advertising chain, err: %d", in ZTEST()
91 "Unexpected error while enabling CTE for periodic advertising chain, err: %d", in ZTEST()
117 "Unexpected error while enabling CTE for periodic advertising chain, err: %d", in ZTEST()
154 "Unexpected error while enabling CTE for periodic advertising chain, err: %d", in ZTEST()
180 "Unexpected error while enabling CTE for periodic advertising chain, err: %d", in ZTEST()
/Zephyr-Core-3.6.0/drivers/spi/
DKconfig.nrfx58 bool "Allow enabling the SPIM driver despite PAN 58"
60 Allow enabling the nRF SPI Master with EasyDMA, despite
71 enabling 'anomaly-58-workaround' via the Devicetree.
/Zephyr-Core-3.6.0/samples/boards/esp32/deep_sleep/src/
Dmain.c71 printk("Enabling timer wakeup, %ds\n", wakeup_time_sec); in main()
80 printk("Enabling EXT1 wakeup on pins GPIO%d, GPIO%d\n", in main()
100 printk("Enabling GPIO wakeup on pins GPIO%d\n", wakeup_button.pin); in main()
/Zephyr-Core-3.6.0/subsys/usb/device/class/dfu/
DKconfig25 Enabling this option makes the device responsible for detaching
45 Enabling this option allows to upload firmware image to the host.
/Zephyr-Core-3.6.0/modules/
DKconfig.tinycrypt48 Enabling ECC requires a cryptographically secure random number
57 Enabling ECC requires a cryptographically secure random number
/Zephyr-Core-3.6.0/soc/arm/st_stm32/stm32l0/
Dsoc.c43 /* On STM32L0, there are some hardfault when enabling DBGMCU bit: in stm32l0_init()
46 * For unclear reason, enabling DMA clock fixes this issue in stm32l0_init()
/Zephyr-Core-3.6.0/subsys/bluetooth/host/
DKconfig.gatt40 enabled additional L2CAP channels can be connected as bearers enabling
217 Enabling this option results in adding PPCP characteristic in GAP.
257 Enabling this option allows remote GATT clients to write to device
265 Enabling this option requires the connection to be encrypted to write
272 Enabling this option requires the connection to be encrypted and
/Zephyr-Core-3.6.0/subsys/mgmt/mcumgr/grp/shell_mgmt/
DKconfig32 on a stack, by the MCUmgr, so enabling MCUMGR_GRP_SHELL and
46 Enabling this options brings back legacy behaviour where the shell
/Zephyr-Core-3.6.0/drivers/sensor/tmd2620/
Dtmd2620.c92 /* enabling interrupt */ in tmd2620_sample_fetch()
96 LOG_ERR("Failed enabling interrupt."); in tmd2620_sample_fetch()
102 /* Enabling proximity and powering up device */ in tmd2620_sample_fetch()
107 LOG_ERR("Failed enabling device."); in tmd2620_sample_fetch()
307 LOG_ERR("Failed enabling wait mode"); in tmd2620_sensor_setup()
349 LOG_ERR("Failed enabling device."); in tmd2620_init()
369 LOG_ERR("Failed enabling sensor."); in tmd2620_pm_action()
/Zephyr-Core-3.6.0/tests/drivers/fuel_gauge/sbs_gauge/
DKconfig10 Enabling this option adds test sources that verify if the battery cutoff extension to the
/Zephyr-Core-3.6.0/samples/sensor/die_temp_polling/boards/
Desp32s3_devkitm.overlay6 * Application overlay for enabling temperature sensor device instance
/Zephyr-Core-3.6.0/subsys/bluetooth/controller/ll_sw/nordic/lll/
Dlll_conn_meta.h10 #error Please define struct lll_conn_meta when enabling BT_CTLR_CONN_META
Dlll_meta.h11 #error Please define typedef struct lll_rx_pdu_meta_t when enabling \
/Zephyr-Core-3.6.0/subsys/bluetooth/controller/ll_sw/openisa/lll/
Dlll_conn_meta.h10 #error Please define struct lll_conn_meta when enabling BT_CTLR_CONN_META
Dlll_meta.h11 #error Please define typedef struct lll_rx_pdu_meta_t when enabling \
/Zephyr-Core-3.6.0/boards/arm/nrf52dk_nrf52810/
DKconfig14 # enabling the controller.
/Zephyr-Core-3.6.0/boards/arm/ubx_bmd330eval_nrf52810/
DKconfig13 # enabling the controller.
/Zephyr-Core-3.6.0/boards/arm/ubx_bmd360eval_nrf52811/
DKconfig12 # enabling the controller.
/Zephyr-Core-3.6.0/doc/services/virtualization/
Divshmem.rst30 by enabling :kconfig:option:`CONFIG_IVSHMEM`. By default, this will expose the plain
39 enabling :kconfig:option:`CONFIG_IVSHMEM_SHELL`.
/Zephyr-Core-3.6.0/dts/bindings/sensor/
Dsensirion,sgp40.yaml16 Enabling this will run a selftest when the driver initializes.

12345678910>>...20