Home
last modified time | relevance | path

Searched +full:dio2 +full:- +full:tx +full:- +full:enable (Results 1 – 9 of 9) sorted by relevance

/Zephyr-latest/dts/bindings/lora/
Dsemtech,sx126x-base.yaml3 # SPDX-License-Identifier: Apache-2.0
5 include: spi-device.yaml
8 reset-gpios:
9 type: phandle-array
13 This signal is open-drain, active-low as interpreted by the
16 busy-gpios:
17 type: phandle-array
21 antenna-enable-gpios:
22 type: phandle-array
24 Antenna power enable pin.
[all …]
/Zephyr-latest/boards/shields/semtech_sx1262mb2das/
Dsemtech_sx1262mb2das.overlay3 * SPDX-License-Identifier: Apache-2.0
15 cs-gpios = <&arduino_header 13 GPIO_ACTIVE_LOW>;
20 spi-max-frequency = <16000000>;
22 reset-gpios = <&arduino_header 0 GPIO_ACTIVE_LOW>;
23 busy-gpios = <&arduino_header 9 GPIO_ACTIVE_HIGH>;
24 antenna-enable-gpios = <&arduino_header 14 GPIO_ACTIVE_HIGH>;
25 dio1-gpios = <&arduino_header 11 GPIO_ACTIVE_HIGH>;
26 dio2-tx-enable;
27 tcxo-power-startup-delay-ms = <5>;
/Zephyr-latest/tests/subsys/lorawan/frag_decoder/boards/
Dnative_sim.overlay4 * SPDX-License-Identifier: Apache-2.0
9 #include <zephyr/dt-bindings/lora/sx126x.h>
13 zephyr,code-partition = &slot0_partition;
21 #address-cells = <1>;
22 #size-cells = <1>;
25 #address-cells = <1>;
26 #size-cells = <0>;
30 clock-frequency = <2000000>;
32 cs-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
38 reset-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
[all …]
/Zephyr-latest/tests/subsys/lorawan/clock_sync/boards/
Dnative_sim.overlay4 * SPDX-License-Identifier: Apache-2.0
9 #include <zephyr/dt-bindings/lora/sx126x.h>
13 zephyr,code-partition = &slot0_partition;
21 #address-cells = <1>;
22 #size-cells = <1>;
25 #address-cells = <1>;
26 #size-cells = <0>;
30 clock-frequency = <2000000>;
32 cs-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
38 reset-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
[all …]
/Zephyr-latest/tests/drivers/build_all/lora/
Dsx1262.overlay3 * SPDX-License-Identifier: Apache-2.0
8 #address-cells = <1>;
9 #size-cells = <1>;
13 gpio-controller;
15 #gpio-cells = <0x2>;
20 #address-cells = <1>;
21 #size-cells = <0>;
26 cs-gpios = <&test_gpio 0 0>,
34 spi-max-frequency = <16000000>;
35 reset-gpios = <&test_gpio 0 0>;
[all …]
/Zephyr-latest/boards/rakwireless/rak4631/
Drak4631_nrf52840.dts4 * SPDX-License-Identifier: Apache-2.0
7 /dts-v1/;
10 #include <zephyr/dt-bindings/lora/sx126x.h>
11 #include "rak4631_nrf52840-pinctrl.dtsi"
19 zephyr,shell-uart = &uart1;
20 zephyr,uart-mcumgr = &uart1;
21 zephyr,bt-mon-uart = &uart1;
22 zephyr,bt-c2h-uart = &uart1;
26 compatible = "gpio-leds";
50 regulator-initial-mode = <NRF5X_REG_MODE_DCDC>;
[all …]
/Zephyr-latest/boards/rakwireless/rak11720/
Drak11720.dts4 * SPDX-License-Identifier: Apache-2.0
7 /dts-v1/;
9 #include <zephyr/dt-bindings/lora/sx126x.h>
10 #include "rak11720_apollo3-pinctrl.dtsi"
11 #include <zephyr/dt-bindings/input/input-event-codes.h>
22 zephyr,shell-uart = &uart0;
23 zephyr,uart-mcumgr = &uart0;
24 zephyr,uart-pipe = &uart0;
25 zephyr,flash-controller = &flash;
27 zephyr,code-partition = &slot0_partition;
[all …]
/Zephyr-latest/boards/heltec/heltec_wireless_stick_lite_v3/
Dheltec_wireless_stick_lite_v3_procpu.dts6 * SPDX-License-Identifier: Apache-2.0
8 /dts-v1/;
11 #include "heltec_wireless_stick_lite_v3-pinctrl.dtsi"
12 #include <zephyr/dt-bindings/pwm/pwm.h>
13 #include <zephyr/dt-bindings/input/input-event-codes.h>
14 #include <zephyr/dt-bindings/lora/sx126x.h>
22 pwm-0 = &ledc0;
23 pwm-led0 = &pwm_led_white;
24 uart-0 = &uart0;
25 uart-1 = &uart1;
[all …]
/Zephyr-latest/drivers/lora/
Dsx126x.c5 * SPDX-License-Identifier: Apache-2.0
65 MODE(TX),
111 const struct spi_buf_set tx = { in sx126x_spi_transceive() local
125 ret = spi_write_dt(&dev_config.bus, &tx); in sx126x_spi_transceive()
127 ret = spi_transceive_dt(&dev_config.bus, &tx, &rx); in sx126x_spi_transceive()
196 LOG_DBG("-> status: 0x%" PRIx8, rx_req[1]); in SX126xReadCommand()
283 * use and then enable the other one. in SX126xSetOperatingMode()
345 LOG_DBG("Configuring DIO2"); in SX126xIoRfSwitchInit()
385 const struct spi_buf_set tx = { in SX126xWakeup() local
391 ret = spi_write_dt(&dev_config.bus, &tx); in SX126xWakeup()
[all …]