Searched full:defaults (Results 1 – 25 of 241) sorted by relevance
12345678910
| /Zephyr-Core-3.5.0/dts/bindings/sensor/ |
| D | nxp,fxas21002-common.yaml | 13 This pin defaults to active low when consumed by the sensor.
21 This pin defaults to active low when produced by the sensor.
29 This pin defaults to active low when produced by the sensor.
|
| D | st,iis2iclx-common.yaml | 11 This pin defaults to active high when produced by the sensor.
25 mandatory and if not present it defaults to 1 which is the
|
| D | st,hts221-common.yaml | 11 This pin defaults to active high when produced by the sensor.
|
| D | adi,adt7310.yaml | 11 The INT signal defaults to active low open drain, so requires a
|
| D | bosch,bmi160.yaml | 13 Zephyr driver maps all interrupts to INT1. The signal defaults
|
| D | bosch,bmi323.yaml | 13 Zephyr driver maps all interrupts to INT1. The signal defaults
|
| D | nxp,fxos8700-common.yaml | 13 This pin defaults to active high when consumed by the sensor.
21 This pin defaults to active low when produced by the sensor.
29 This pin defaults to active low when produced by the sensor.
|
| D | st,ism330dhcx-common.yaml | 12 This pin defaults to active high when produced by the sensor.
28 mandatory and if not present it defaults to 1 which is the
|
| D | adi,adt7420.yaml | 14 The INT signal defaults to active low open drain, so requires a
|
| D | st,iis2dh-i2c.yaml | 16 This pin defaults to active high when produced by the sensor.
|
| D | st,iis2dh-spi.yaml | 16 This pin defaults to active high when produced by the sensor.
|
| /Zephyr-Core-3.5.0/dts/bindings/display/ |
| D | st,stm32-ltdc.yaml | 54 description: First pixel in x direction on layer 0. Defaults to 0.
58 description: Last pixel in x direction on layer 0. Defaults to width.
62 description: First pixel in y direction on layer 0. Defaults to 0.
66 description: Last pixel in y direction on layer 0. Defaults to height.
|
| D | solomon,ssd16xx-common.yaml | 57 defaults loaded from the controllers OTP memory.
60 has been specified. That profile may be empty to use the defaults
|
| /Zephyr-Core-3.5.0/dts/bindings/mfd/ |
| D | nordic,npm6001.yaml | 30 description: Input type for BUCK_MODE0 pin. Defaults IC boot-time value.
40 description: Input type for BUCK_MODE1 pin. Defaults IC boot-time value.
50 description: Input type for BUCK_MODE2 pin. Defaults IC boot-time value.
|
| /Zephyr-Core-3.5.0/soc/riscv/riscv-privileged/andes_v5/ |
| D | Kconfig.defconfig.series | 7 # SoC defaults should be parsed before SoC Series defaults, because SoCs usually
|
| /Zephyr-Core-3.5.0/dts/bindings/input/ |
| D | hynitron,cst816s.yaml | 14 The irq signal defaults to active low as produced by the
21 The reset signal defaults to active low to the
|
| /Zephyr-Core-3.5.0/tests/drivers/regulator/voltage/dts/bindings/ |
| D | test-regulator-voltage.yaml | 38 Number of ADC readings to average. Defaults to 1 (no average).
44 Delay between voltage set and ADC read. Defaults to 0 (no delay).
|
| /Zephyr-Core-3.5.0/samples/bluetooth/hci_uart/boards/ |
| D | nrf9160dk_nrf52840.conf | 1 # Override prj.conf defaults
|
| /Zephyr-Core-3.5.0/dts/bindings/sdhc/ |
| D | nxp,imx-usdhc.yaml | 45 This pin defaults to active high when consumed by the SD card. The
53 This pin defaults to active low when produced by the SD card. The
|
| /Zephyr-Core-3.5.0/samples/drivers/jesd216/boards/ |
| D | mr_canhubk3.conf | 4 # Override defaults for SPI NOR flash driver
|
| /Zephyr-Core-3.5.0/dts/bindings/mipi-dsi/ |
| D | st,stm32-mipi-dsi.yaml | 71 defaults to HAL_DSI_ERROR_NONE.
77 Defaults to 0 which disables the filter.
|
| /Zephyr-Core-3.5.0/samples/posix/eventfd/ |
| D | prj.conf | 7 # so provide reasonable defaults so it can be built.
|
| /Zephyr-Core-3.5.0/samples/sensor/bme280/ |
| D | Kconfig | 14 # the device connected either way. These defaults can be overridden if
|
| /Zephyr-Core-3.5.0/dts/bindings/rtc/ |
| D | rtc-device.yaml | 14 alarms defaults to 0, which indicates that the RTC has
|
| /Zephyr-Core-3.5.0/dts/bindings/spi/ |
| D | microchip,xec-qmspi-ldma.yaml | 42 Defaults to 1 for full duplex driver's support for full-duplex spi.
52 Ports 1 and 2 implement CS0# only. Defaults to CS0#.
|
12345678910
