Searched full:defaults (Results 1 – 25 of 151) sorted by relevance
1234567
| /Zephyr-Core-2.7.6/dts/bindings/sensor/ |
| D | nxp,fxas21002.yaml | 16 This pin defaults to active low when produced by the sensor.
25 This pin defaults to active low when produced by the sensor.
|
| D | st,lsm6dso-common.yaml | 10 This pin defaults to active high when produced by the sensor.
25 mandatory and if not present it defaults to 1 which is the
|
| D | st,iis2iclx-common.yaml | 10 This pin defaults to active high when produced by the sensor.
25 mandatory and if not present it defaults to 1 which is the
|
| D | nxp,fxos8700.yaml | 16 This pin defaults to active high when consumed by the sensor.
25 This pin defaults to active low when produced by the sensor.
34 This pin defaults to active low when produced by the sensor.
|
| D | st,ism330dhcx-common.yaml | 11 This pin defaults to active high when produced by the sensor.
28 mandatory and if not present it defaults to 1 which is the
|
| D | st,iis2mdc-i2c.yaml | 17 This pin defaults to active high when produced by the sensor.
|
| D | st,iis2mdc-spi.yaml | 17 This pin defaults to active high when produced by the sensor.
|
| D | st,hts221.yaml | 16 This pin defaults to active high when produced by the sensor.
|
| D | adi,adt7420.yaml | 15 The INT signal defaults to active low open drain, so requires a
|
| D | adi,adxl362.yaml | 15 The INT1 signal defaults to active high as produced by the
|
| D | bosch,bmi160.yaml | 16 Zephyr driver maps all interrupts to INT1. The signal defaults
|
| D | st,iis2dh-i2c.yaml | 17 This pin defaults to active high when produced by the sensor.
|
| D | st,iis2dh-spi.yaml | 17 This pin defaults to active high when produced by the sensor.
|
| D | st,lis2ds12-i2c.yaml | 16 This pin defaults to active high when produced by the sensor.
|
| D | st,lis3mdl-magn.yaml | 16 This pin defaults to active high when produced by the sensor.
|
| D | adi,adxl372-i2c.yaml | 15 The INT1 signal defaults to active high as produced by the
|
| D | st,iis3dhhc-spi.yaml | 17 This pin defaults to active high when produced by the sensor.
|
| D | st,lis2ds12-spi.yaml | 17 This pin defaults to active high when produced by the sensor.
|
| /Zephyr-Core-2.7.6/soc/riscv/riscv-privilege/andes_v5/ |
| D | Kconfig.defconfig.series | 7 # SoC defaults should be parsed before SoC Series defaults, because SoCs usually
|
| /Zephyr-Core-2.7.6/dts/bindings/mmc/ |
| D | nxp,imx-usdhc.yaml | 19 This pin defaults to active high when consumed by the SD card. The
28 This pin defaults to active low when produced by the SD card. The
|
| /Zephyr-Core-2.7.6/scripts/west_commands/runners/ |
| D | intel_s1000.py | 41 help='ocd-dir, defaults to /opt/tensilica/xocd-12.0.4/xt-ocd')
44 help='ocd-topology, defaults to topology_dsp0_flyswatter2.xml')
47 help='ocd-jtag-instr, defaults to dsp0_gdb.txt')
50 help='gdb-flash-file, defaults to load_elf.txt')
53 help='xt-gdb port, defaults to 20000')
|
| /Zephyr-Core-2.7.6/samples/bluetooth/hci_uart/boards/ |
| D | nrf9160dk_nrf52840.conf | 1 # Override prj.conf defaults
|
| /Zephyr-Core-2.7.6/samples/posix/eventfd/ |
| D | prj.conf | 8 # so provide reasonable defaults so it can be built.
|
| /Zephyr-Core-2.7.6/samples/net/syslog_net/ |
| D | Kconfig | 13 zero means that the defaults in the application are used.
|
| /Zephyr-Core-2.7.6/samples/sensor/bme280/ |
| D | Kconfig | 14 # the device connected either way. These defaults can be overridden if
|
1234567
