Searched full:applies (Results 1 – 25 of 155) sorted by relevance
1234567
| /Zephyr-Core-3.7.0/dts/bindings/qspi/ |
| D | nxp,s32-qspi.yaml | 130 This property applies to side A of the controller.
137 This property applies to side A of the controller.
148 This property applies to side A of the controller.
154 This property applies to side A of the controller.
164 This property applies to side A of the controller.
174 This property applies to side A of the controller.
184 This property applies to side A of the controller.
194 This property applies to side A of the controller.
203 This property applies to side A of the controller.
|
| /Zephyr-Core-3.7.0/soc/nxp/imx/imx6sx/ |
| D | soc_clk_freq.h | 19 * @brief Get clock frequency applies to the PWM module
22 * @return clock frequency (in HZ) applies to the PWM module
|
| /Zephyr-Core-3.7.0/dts/bindings/pinctrl/ |
| D | gd,gd32-pinctrl-afio.yaml | 68 applies for GPIO_IN mode.
69 - drive-open-drain: Open-drain drive mode. Only applies for GPIO_IN mode.
70 - bias-disable: Disable pull-up/down (default, not required). Only applies
72 - bias-pull-up: Enable pull-up resistor. Only applies for GPIO_IN mode.
73 - bias-pull-down: Enable pull-down resistor. Only applies for GPIO_IN mode.
75 signal (default: 2MHz). Only applies for ALTERNATE mode.
|
| /Zephyr-Core-3.7.0/soc/nxp/imx/imx7d/ |
| D | soc_clk_freq.h | 19 * @brief Get clock frequency applies to the PWM module
22 * @return clock frequency (in HZ) applies to the PWM module
|
| /Zephyr-Core-3.7.0/tests/bsim/bluetooth/host/misc/hfc_multilink/tester/ |
| D | prj.conf | 15 # FIXME: check if this still applies
|
| /Zephyr-Core-3.7.0/include/zephyr/drivers/serial/ |
| D | uart_ns16550.h | 19 * @note This only applies to Synopsys Designware UART IP block.
|
| /Zephyr-Core-3.7.0/tests/drivers/clock_control/stm32_clock_configuration/stm32_common_core/boards/ |
| D | msi_range11.overlay | 9 * It is assumed that applies after clear all clocks with .overlay file.
|
| D | wl_32_hse.overlay | 10 * It applies to the stm32wl where the hse prescaler is 1 and by-passed
|
| D | pll_48_msi_4.overlay | 10 * It applies to the stm32xx where the msi is 4MHz
|
| D | wb_pll_48_hsi_16.overlay | 10 * It applies to the stm32wb
|
| D | wb_pll_48_msi_4.overlay | 10 * It applies to the stm32wb where the msi is 4MHz
|
| D | wb_pll_64_hse_32.overlay | 10 * It applies to the stm32wb
|
| D | wl_pll_48_hse_32.overlay | 10 * It applies to the stm32wl where the hse prescaler is 2 and by-passed
|
| /Zephyr-Core-3.7.0/soc/nordic/nrf52/ |
| D | Kconfig | 84 This anomaly applies to IC revisions "Engineering B" up to "3", the most
96 This anomaly applies to IC revisions up to "3", the most recent one.
|
| /Zephyr-Core-3.7.0/dts/bindings/can/ |
| D | zephyr,native-linux-can.yaml | 17 option. Note that it applies for every instance of this driver.
|
| /Zephyr-Core-3.7.0/doc/build/snippets/ |
| D | index.rst | 8 configuration separately when it applies to multiple different applications.
|
| /Zephyr-Core-3.7.0/dts/bindings/sensor/ |
| D | adi,adxl362.yaml | 29 Only applies for Linked and Loop mode, ignored otherwise.
|
| /Zephyr-Core-3.7.0/subsys/usb/usb_c/ |
| D | usbc_tc_snk_states_internal.h | 31 * @brief Super state that applies Rd
|
| D | usbc_tc_common_internal.h | 34 /** Super state that applies Rd to the CC lines */
43 /** Super state that applies Rp to the CC lines */
|
| /Zephyr-Core-3.7.0/subsys/net/lib/tls_credentials/ |
| D | Kconfig.shell | 25 output should be. Must be a multiple of 4. Applies only to ??? mode.
|
| /Zephyr-Core-3.7.0/drivers/display/ |
| D | Kconfig.sdl | 60 This applies when the pixel format is MONO01/MONO10.
|
| /Zephyr-Core-3.7.0/doc/project/ |
| D | communication.rst | 18 the mailing list. The same applies to code reviews.
|
| /Zephyr-Core-3.7.0/dts/bindings/spi/ |
| D | nxp,lpc-spi.yaml | 40 Applies to SPI master and slave configurations.
|
| /Zephyr-Core-3.7.0/subsys/net/lib/lwm2m/ |
| D | README_lwm2m | 22 The above command also applies the lwm2m_senml_cbor.patch patch file.
|
| /Zephyr-Core-3.7.0/include/zephyr/drivers/led/ |
| D | is31fl3733.h | 26 * from per-led brightness, and applies to all LEDs.
|
1234567
