Searched full:vin (Results 1 – 25 of 44) sorted by relevance
12
| /Zephyr-latest/boards/nordic/thingy52/ |
| D | thingy52_nrf52832.dts | 44 //vin-supply = <&vdd_pwr>;
49 //vin-supply = <&vdd_pwr>;
54 //vin-supply = <&vdd_pwr>;
144 vin-supply = <&vdd_pwr>;
156 vin-supply = <&vdd_pwr>;
162 vin-supply = <&vdd_pwr>;
169 vin-supply = <&ccs_pwr>;
|
| /Zephyr-latest/dts/bindings/base/ |
| D | power.yaml | 16 Contrast with vin-supply.
18 vin-supply:
|
| /Zephyr-latest/samples/subsys/mgmt/hawkbit/src/ |
| D | main.c | 27 const char *VIN; member
37 JSON_OBJ_DESCR_PRIM(struct hawkbit_cfg_data, VIN, JSON_TOK_STRING),
50 .data.VIN = device_id, in hawkbit_new_config_data_cb()
|
| /Zephyr-latest/dts/bindings/regulator/ |
| D | nxp,pca9420.yaml | 40 nxp,vin-ilim-microamp:
52 VIN input current limit, in microamperes. Value reflects typical value,
|
| /Zephyr-latest/dts/bindings/sensor/ |
| D | hzgrow,r502a.yaml | 19 vin-gpios:
|
| /Zephyr-latest/drivers/sensor/grow_r502a/ |
| D | Kconfig | 68 Enable control of vin-gpios and act-gpios.
|
| /Zephyr-latest/dts/bindings/gpio/ |
| D | arduino-nano-header-r3.yaml | 19 1 D1 VIN -
|
| D | adi,sdp-120.yaml | 11 1 VIN NC 120
|
| D | panasonic,reduced-arduino-header.yaml | 18 - VIN D7 NC
|
| D | arduino-header-r3.yaml | 38 - VIN D7 13
|
| D | arduino-mkr-header.yaml | 22 15 A0/D15/DAC0 VIN -
|
| /Zephyr-latest/samples/sensor/mpr/ |
| D | README.rst | 22 interface. Connect **VIN**, **GND** and Interface: **SDA**, **SCL**.
|
| /Zephyr-latest/subsys/mgmt/hawkbit/ |
| D | hawkbit_priv.h | 78 const char *VIN; member
|
| /Zephyr-latest/boards/actinius/icarus/ |
| D | feather_connector.dtsi | 24 /* 11 is VIN */
|
| /Zephyr-latest/drivers/regulator/ |
| D | regulator_pca9420.c | 38 /** @brief VIN input current limit selection */
99 /** VIN ILIM resolution, uA/LSB */
101 /** VIN ILIM minimum value, uA */
487 /* configure VIN current limit */ in regulator_pca9420_common_init()
|
| /Zephyr-latest/boards/adi/sdp_k1/doc/ |
| D | index.rst | 17 - VIN from Arduino* compatible connectors
18 - VIN from 120-pin connector 5 V min. 300 mA
|
| /Zephyr-latest/boards/particle/nrf51_blenano/doc/ |
| D | index.rst | 74 with the VIN and GND pins should face **towards** the USB connector.
|
| /Zephyr-latest/boards/m5stack/m5stack_core2/ |
| D | m5stack_core2_procpu.dts | 69 vin-supply = <&lcd_bg>;
|
| /Zephyr-latest/boards/particle/nrf52_blenano2/doc/ |
| D | index.rst | 73 with the VIN and GND pins should face **towards** the USB
|
| /Zephyr-latest/boards/st/stm32f469i_disco/doc/ |
| D | index.rst | 17 - VIN from Arduino* compatible connectors
|
| /Zephyr-latest/boards/st/stm32f412g_disco/doc/ |
| D | index.rst | 31 - VIN from Arduino* connectors
|
| /Zephyr-latest/boards/st/stm32f413h_disco/doc/ |
| D | index.rst | 32 - VIN from Arduino* connectors
|
| /Zephyr-latest/boards/st/stm32f429i_disc1/doc/ |
| D | index.rst | 17 - VIN from Arduino* compatible connectors
|
| /Zephyr-latest/boards/st/nucleo_g0b1re/doc/ |
| D | index.rst | 19 - VIN (7 - 12V) from ARDUINO connector or ST morpho connector
|
| /Zephyr-latest/boards/st/b_l072z_lrwan1/doc/ |
| D | index.rst | 42 - Through USB bus or external VIN/3.3 V supply voltage or batteries
|
12
