Searched full:rs485 (Results 1 – 18 of 18) sorted by relevance
| /Zephyr-Core-3.5.0/dts/bindings/serial/ |
| D | nxp,kinetis-lpuart.yaml | 21 nxp,rs485-mode:
28 nxp,rs485-de-active-low:
30 description: RTS polarity at RS485 mode.
|
| D | espressif,esp32-uart.yaml | 17 hw-rs485-hd-mode:
20 Enable the hardware RS485 half duplex mode.
|
| /Zephyr-Core-3.5.0/doc/services/modbus/ |
| D | index.rst | 9 with different physical interfaces, like RS485 or RS232.
|
| /Zephyr-Core-3.5.0/boards/arm/mimx8mm_phyboard_polis/ |
| D | mimx8mm_phyboard_polis.dts | 49 /* RS232 / RS485 pinheader on the board */
|
| /Zephyr-Core-3.5.0/samples/subsys/modbus/rtu_client/ |
| D | README.rst | 61 .. _`joy-it RS-485 shield for Arduino`: https://joy-it.net/en/products/ARD-RS485
|
| /Zephyr-Core-3.5.0/boards/arm/stm32g081b_eval/doc/ |
| D | index.rst | 17 with USB PD, motor control connector, RS232, RS485, Audio DAC, microphone ADC,
50 - RS-232 and RS485 communications
|
| /Zephyr-Core-3.5.0/samples/subsys/modbus/rtu_server/ |
| D | README.rst | 152 .. _`joy-it RS-485 shield for Arduino`: https://joy-it.net/en/products/ARD-RS485
|
| /Zephyr-Core-3.5.0/boards/arm/stm32f072_eval/doc/ |
| D | index.rst | 18 - RS232 and RS485 communication
|
| /Zephyr-Core-3.5.0/boards/arm/mimx8mm_phyboard_polis/doc/ |
| D | index.rst | 43 - 1x RS232 / RS485
116 | RS232/485 | UART1 | RS232 / RS485 with flow-control |
|
| /Zephyr-Core-3.5.0/boards/arm/nucleo_f446re/doc/ |
| D | index.rst | 162 used with `RS485 CAN Shield`_.
|
| /Zephyr-Core-3.5.0/boards/arm/stm32f3_seco_d23/doc/ |
| D | index.rst | 46 - RS485
|
| /Zephyr-Core-3.5.0/boards/arm/mimx8mp_phyboard_pollux/doc/ |
| D | index.rst | 29 - Serial: 1x RS232 / RS485 Full Duplex / Half Duplex
|
| /Zephyr-Core-3.5.0/drivers/serial/ |
| D | uart_mcux_lpuart.c | 998 /* Set the LPUART into RS485 mode (tx driver enable using RTS) */ in mcux_lpuart_configure_init()
|
| D | uart_stm32.c | 556 /* Driver supports only RTS/CTS and RS485 flow control */ in uart_stm32_configure()
|
| /Zephyr-Core-3.5.0/include/zephyr/drivers/ |
| D | uart.h | 113 UART_CFG_FLOW_CTRL_RS485, /**< RS485 flow control */
|
| /Zephyr-Core-3.5.0/doc/releases/ |
| D | release-notes-3.5.rst | 732 * Added RS485 support.
|
| D | release-notes-3.3.rst | 1698 - new property: ``nxp,rs485-mode``
1699 - new property: ``nxp,rs485-de-active-low``
|
| D | release-notes-2.7.rst | 1196 * :github:`38264` - Modbus over RS485 on samd21g18a re-gpios turning on 1 byte too early
|
