Searched full:p10 (Results 1 – 22 of 22) sorted by relevance
| /Zephyr-Core-3.7.0/samples/drivers/adc/adc_dt/boards/ |
| D | cy8cproto_062_4343w.overlay | 27 zephyr,input-positive = <0>; /* P10.0 */
36 zephyr,input-positive = <1>; /* P10.1 */
45 zephyr,input-positive = <2>; /* P10.2 */
54 zephyr,input-positive = <3>; /* P10.3 */
|
| D | cy8cproto_063_ble.overlay | 27 zephyr,input-positive = <2>; /* P10.2 */
36 zephyr,input-positive = <3>; /* P10.3 */
45 zephyr,input-positive = <4>; /* P10.4 */
54 zephyr,input-positive = <5>; /* P10.5 */
|
| /Zephyr-Core-3.7.0/dts/bindings/adc/ |
| D | infineon,cat1-adc.yaml | 10 the board. For example on the cy8cproto_062_4343w P10.0 is mapped to adc0,channel0 and
11 P10.1 is mapped to adc0,channel1.
|
| /Zephyr-Core-3.7.0/samples/drivers/adc/adc_sequence/boards/ |
| D | cy8cproto_062_4343w.overlay | 25 zephyr,input-positive = <0>; /* P10.0 */
33 zephyr,input-positive = <1>; /* P10.1 */
|
| D | cy8cproto_063_ble.overlay | 25 zephyr,input-positive = <2>; /* P10.2 */
33 zephyr,input-positive = <3>; /* P10.3 */
|
| /Zephyr-Core-3.7.0/tests/drivers/adc/adc_api/boards/ |
| D | cy8cproto_062_4343w.overlay | 27 zephyr,input-positive = <0>; /* P10.0 */
36 zephyr,input-positive = <1>; /* P10.1 */
|
| D | cy8cproto_063_ble.overlay | 27 zephyr,input-positive = <2>; /* P10.2 */
36 zephyr,input-positive = <3>; /* P10.3 */
|
| /Zephyr-Core-3.7.0/dts/bindings/gpio/ |
| D | nordic-thingy53-edge-connector.yaml | 15 P10 LOAD_SW_DISABLE
|
| /Zephyr-Core-3.7.0/boards/bbc/microbit/ |
| D | board.h | 25 #define EXT_P10_GPIO_PIN 6 /* P10, Analog in, LED Col 3 */
|
| D | bbc_microbit.dts | 93 <10 0 &gpio0 6 0>, /* P10, Analog in, LED Col 3 */
|
| /Zephyr-Core-3.7.0/include/zephyr/dt-bindings/pinctrl/ |
| D | ifx_cat1-pinctrl.h | 84 #define P10 CYHAL_PORT_10 macro
|
| /Zephyr-Core-3.7.0/boards/shields/amg88xx/doc/ |
| D | index.rst | 74 P10: LDO_EN.
81 * P10: LDO_EN
|
| /Zephyr-Core-3.7.0/drivers/sensor/bosch/bmp388/ |
| D | bmp388.h | 154 int8_t p10; member
|
| D | bmp388.c | 349 partial_data2 = cal->p10 * t_lin; in bmp388_compensate_press()
|
| /Zephyr-Core-3.7.0/drivers/gpio/ |
| D | gpio_pcf857x.c | 76 *value = sys_get_le16(rx_buf); /*format P17-P10..P07-P00 (bit15-bit8..bit7-bit0)*/ in pcf857x_process_input()
270 * @param pins The pin(s) which will be set in a range from P17-P10..P07-P00
|
| /Zephyr-Core-3.7.0/boards/bbc/microbit_v2/ |
| D | bbc_microbit_v2.dts | 92 <10 0 &gpio0 30 0>, /* P10 */
|
| /Zephyr-Core-3.7.0/scripts/tests/twister/ |
| D | test_hardwaremap.py | 560 platform: p10
593 'platform': 'p10',
|
| /Zephyr-Core-3.7.0/drivers/audio/ |
| D | tlv320dac310x.c | 368 LOG_INF("PCM Rate: %u Filter B PRB P10 selected", in codec_configure_filters()
|
| /Zephyr-Core-3.7.0/boards/microchip/mec1501modular_assy6885/doc/ |
| D | index.rst | 125 If you wish to power from type A/B connector ``P10`` set the jumper ``JP35 1-2``.
|
| /Zephyr-Core-3.7.0/boards/madmachine/mm_feather/doc/ |
| D | index.rst | 114 | P10 | GPIO_AD_B1_02 | D10 | GPIO1_IO18 | | |
|
| /Zephyr-Core-3.7.0/boards/madmachine/mm_swiftio/doc/ |
| D | index.rst | 96 | P10 | GPIO_B1_03 | D10 | GPIO2_IO19 | | |
|
| /Zephyr-Core-3.7.0/boards/nordic/nrf52dk/doc/ |
| D | index.rst | 304 P4/P10 Digital I/O
|
