Searched full:determine (Results 1 – 25 of 458) sorted by relevance
12345678910>>...19
38 Value of the GHWCFG1 register. It is used to determine available endpoint45 Value of the GHWCFG2 register. It is used to determine available endpoint52 Value of the GHWCFG4 register. It is used to determine available endpoint
20 - New device drivers shall use devicetree APIs to determine which :ref:`devices24 determine which of multiple possible generic devices of a given type will be26 determine the LED to blink.35 determine the hardware supported by a board. This should be obtained from38 - Legacy device drivers currently use Kconfig to determine which instances of a
22 * @ref log_const_source_id or @ref log_dynamic_source_id can be used to determine42 * @ref log_const_source_id or @ref log_dynamic_source_id can be used to determine56 * @ref log_const_source_id or @ref log_dynamic_source_id can be used to determine71 * @ref log_const_source_id or @ref log_dynamic_source_id can be used to determine
30 * @brief Determine if the DAPlink shield is fitted.32 * Determine if the DAPlink shield is fitted based on the state of the
30 This flag is used to determine size of internal structures that37 This flag is used to determine size of internal structures that
38 #. Use :c:func:`net_timeout_evaluate()` to determine how long it is until the41 again to determine whether the timeout has completed, or whether there is51 determine the next timeout event to occur.
70 * within the target. These fields enable the target to determine whether the command is76 * within the target. These fields enable the target to determine whether the command is86 * within the target. These fields enable the target to determine whether the command is93 * within the target. These fields enable the target to determine whether the command is
17 The SAR Transmitter procedure is used to determine and configure the SAR Transmitter state of a SAR22 The SAR Receiver procedure is used to determine and configure the SAR Receiver state of a SAR
17 * Use this macro to determine the length of the bString array.34 * Use this macro to determine the bLength of the string descriptor.
160 * @brief Minimum time a port shall wait before it can determine it is attached166 * @brief Maximum time a port shall wait before it can determine it is attached172 * @brief Minimum time a Sink port shall wait before it can determine it is detached due to179 * @brief Maximum time a Sink port shall wait before it can determine it is detached due to186 * @brief Minimum Time a port shall wait before it can determine it is re-attached during193 * @brief Maximum Time a port shall wait before it can determine it is re-attached during213 * @brief Minimum time a Sink port shall wait before it can determine there has been a change220 * @brief Maximum time a Sink port shall wait before it can determine there has been a change
34 * Determine if the core executing this code is the master or47 /* Determine which core (M0+ or M4) this code is running on */60 /* Determine if M4 core is the master or slave */
5 Quadrature Decoder driver which processes encoder signals to determine motor revs51 This is a number that is used to determine how many revolutions * 1000000106 This array configures the input indices to the LCU module which help to determine the
22 VDDA/VREF+ voltage in millivolts applied during manufacturing to determine
19 use probing mode to determine the I2C address rather than setting the
24 To determine the maximum rx filters can be added on this CAN device.
9 then commonly be inspected by reading registers to determine which event caused
85 compared directly to a user set threshold to determine whether94 compared directly to a user set threshold to determine whether
58 that covers the memory access to determine the enforcement policy. Others may59 logically OR regions to determine enforcement policy.
9 Internal helper macro to determine if the main `thread` command
58 response team will analyze the issue, determine a responsible96 attendance. During this review, they shall determine if new issues145 vetted by the project director to determine that they have a154 to determine if they need to backport these changes to any internal
22 will be used to determine the interval for which the number of
12 Reset cause flags can be used to determine why the device was reset; for
31 Virtual Register (LVR) of all connected I2C devices to determine
13 # command line arguments while invoking xt-clang to determine
5 Implement a basic Power Delivery Analyzer to determine if a USB device is currently charging.
