Searched full:d8 (Results 1 – 25 of 281) sorted by relevance
12345678910>>...12
| /Zephyr-latest/dts/bindings/gpio/ |
| D | panasonic,reduced-arduino-header.yaml | 16 - GND D8 NC
44 Arduino UNO layout, labeled from D8 at the bottom through D15 at the top,
45 but D8 and D9 are not connected.
|
| D | nxp,cam-44pins-connector.yaml | 17 18 MIPI_CSI_DN1/D8 PWDN 17
19 22 MIPI_CSI_CLKP/D7 MIPI_CSI_DN1/D8 21
|
| D | arduino-header-r3.yaml | 19 digital input signals labelled from D8 at the bottom through D13
36 - GND D8 14
|
| D | seeed-xiao-header.yaml | 27 5 D5 D8 8
|
| /Zephyr-latest/tests/drivers/uart/uart_async_api/boards/ |
| D | nucleo_f103rb.overlay | 3 /* Connect pin (PA10) D2 of the CN9:2 to D8 (PA9) of the CN5:1 */
|
| /Zephyr-latest/boards/shields/arceli_eth_w5500/ |
| D | arceli_eth_w5500.overlay | 13 reset-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>; /* D8 */
|
| /Zephyr-latest/samples/drivers/counter/maxim_ds3231/boards/ |
| D | nucleo_l476rg.overlay | 7 &i2c1 { /* SDA CN5.9=PB9, SCL CN5.10=PB8, ISW CN5.1=D8=PA9 */
|
| /Zephyr-latest/tests/drivers/counter/maxim_ds3231_api/boards/ |
| D | nucleo_l476rg.overlay | 7 &i2c1 { /* SDA CN5.9=PB9, SCL CN5.10=PB8, ISW CN5.1=D8=PA9 */
|
| /Zephyr-latest/samples/sensor/sht3xd/boards/ |
| D | nucleo_l476rg.overlay | 7 &i2c1 { /* SDA CN5.9=PB9, SCL CN5.10=PB8, ALERT CN5.1=D8=PA9 */
|
| /Zephyr-latest/tests/misc/print_format/ |
| D | testcase.yaml | 9 - "d8"
|
| /Zephyr-latest/boards/shields/mcp2515/ |
| D | keyestudio_can_bus_ks0411.overlay | 14 int-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>; /* D8 */
|
| /Zephyr-latest/boards/shields/atmel_rf2xx/ |
| D | atmel_rf2xx_arduino.overlay | 27 /* D8 */
|
| /Zephyr-latest/boards/shields/ls0xx_generic/ |
| D | ls013b7dh03.overlay | 23 extcomin-gpios = <&arduino_header 14 GPIO_ACTIVE_HIGH>; /* D8 */
|
| /Zephyr-latest/samples/sensor/tdk_apex/boards/ |
| D | nrf52dk_nrf52832_spi.overlay | 21 cs-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>; /* D8 */
|
| /Zephyr-latest/boards/shields/wnc_m14a2a/boards/ |
| D | frdm_k64f.overlay | 22 mdm-reset-gpios = <&arduino_header 14 GPIO_ACTIVE_HIGH>; /* D8 */
|
| /Zephyr-latest/boards/shields/nrf7002ek/ |
| D | nrf7002ek_common.dtsi | 17 /* D8 */
|
| /Zephyr-latest/boards/shields/waveshare_epaper/ |
| D | waveshare_epaper_gdeh0154a07.overlay | 18 reset-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>; /* D8 */
|
| D | waveshare_epaper_gdew042t2.overlay | 17 reset-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>; /* D8 */
|
| D | waveshare_epaper_gdey0213b74.overlay | 18 reset-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>; /* D8 */
|
| D | waveshare_epaper_gdew075t7.overlay | 18 reset-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>; /* D8 */
|
| /Zephyr-latest/boards/nordic/nrf9161dk/ |
| D | nrf9161dk_nrf9161_common_0_7_0.dtsi | 20 10 d8 00 ff d5 31 b1 fe 82 e4 14 4c ec 60 06 33
|
| /Zephyr-latest/tests/drivers/stepper/stepper_api/boards/ |
| D | nucleo_f767zi.overlay | 24 en-gpios = <&arduino_header 14 0>; /* D8 */
|
| /Zephyr-latest/boards/st/nucleo_wb05kz/ |
| D | arduino_r3_connector.dtsi | 18 gpio-map = <14 0 &gpiob 15 0>, /* D8 */
|
| /Zephyr-latest/boards/st/nucleo_wb09ke/ |
| D | arduino_r3_connector.dtsi | 18 gpio-map = <14 0 &gpiob 15 0>, /* D8 */
|
| /Zephyr-latest/tests/drivers/flash/common/boards/ |
| D | nrf52840dk_mx25r_high_perf.overlay | 20 10 d8 00 ff 23 72 f5 00 82 ed 04 cc 44 83 68 44
|
12345678910>>...12
