Searched full:d8 (Results 1 – 25 of 209) sorted by relevance
123456789
| /Zephyr-Core-3.4.0/dts/bindings/gpio/ |
| D | panasonic,reduced-arduino-header.yaml | 16 - GND D8 NC
44 Arduino UNO layout, labeled from D8 at the bottom through D15 at the top,
45 but D8 and D9 are not connected.
|
| D | arduino-header-r3.yaml | 19 digital input signals labelled from D8 at the bottom through D13
36 - GND D8 14
|
| D | seeed-xiao-header.yaml | 27 5 D5 D8 8
|
| D | sparkfun-pro-micro-header.yaml | 29 8 D8 D16 16
|
| D | arduino-nano-header-r3.yaml | 29 8 D8 A1/D15 15
|
| D | arduino-mkr-header.yaml | 32 3 D3 D8/COPI 8
|
| /Zephyr-Core-3.4.0/tests/drivers/uart/uart_async_api/boards/ |
| D | nucleo_f103rb.overlay | 3 /* Connect pin (PA10) D2 of the CN9:2 to D8 (PA9) of the CN5:1 */
|
| /Zephyr-Core-3.4.0/boards/shields/arceli_eth_w5500/ |
| D | arceli_eth_w5500.overlay | 13 reset-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>; /* D8 */
|
| /Zephyr-Core-3.4.0/tests/drivers/counter/maxim_ds3231_api/boards/ |
| D | nucleo_l476rg.overlay | 7 &i2c1 { /* SDA CN5.9=PB9, SCL CN5.10=PB8, ISW CN5.1=D8=PA9 */
|
| /Zephyr-Core-3.4.0/samples/drivers/counter/maxim_ds3231/boards/ |
| D | nucleo_l476rg.overlay | 7 &i2c1 { /* SDA CN5.9=PB9, SCL CN5.10=PB8, ISW CN5.1=D8=PA9 */
|
| /Zephyr-Core-3.4.0/tests/misc/print_format/ |
| D | testcase.yaml | 9 - "d8"
|
| /Zephyr-Core-3.4.0/samples/sensor/sht3xd/boards/ |
| D | nucleo_l476rg.overlay | 7 &i2c1 { /* SDA CN5.9=PB9, SCL CN5.10=PB8, ALERT CN5.1=D8=PA9 */
|
| /Zephyr-Core-3.4.0/boards/shields/ls0xx_generic/ |
| D | ls013b7dh03.overlay | 23 extcomin-gpios = <&arduino_header 14 GPIO_ACTIVE_HIGH>; /* D8 */
|
| /Zephyr-Core-3.4.0/boards/shields/atmel_rf2xx/ |
| D | atmel_rf2xx_arduino.overlay | 27 /* D8 */
|
| /Zephyr-Core-3.4.0/boards/shields/mcp2515/ |
| D | keyestudio_can_bus_ks0411.overlay | 14 int-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>; /* D8 */
|
| /Zephyr-Core-3.4.0/boards/shields/waveshare_epaper/ |
| D | waveshare_epaper_gdeh0154a07.overlay | 23 reset-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>; /* D8 */
|
| D | waveshare_epaper_gdew042t2.overlay | 22 reset-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>; /* D8 */
|
| D | waveshare_epaper_gdew075t7.overlay | 23 reset-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>; /* D8 */
|
| D | waveshare_epaper_gdeh029a1.overlay | 23 reset-gpios = <&arduino_header 14 GPIO_ACTIVE_LOW>; /* D8 */
|
| /Zephyr-Core-3.4.0/boards/shields/wnc_m14a2a/boards/ |
| D | frdm_k64f.overlay | 22 mdm-reset-gpios = <&arduino_header 14 GPIO_ACTIVE_HIGH>; /* D8 */
|
| /Zephyr-Core-3.4.0/tests/drivers/flash/common/boards/ |
| D | nrf52840dk_mx25r_high_perf.overlay | 16 10 d8 00 ff 23 72 f5 00 82 ed 04 cc 44 83 68 44
|
| /Zephyr-Core-3.4.0/samples/bluetooth/ipsp/ |
| D | README.rst | 69 [bt] [INF] show_dev_info: Identity: cb:af:14:57:d8:6e (random)
109 CB:AF:14:57:D8:6E (unknown)
110 CB:AF:14:57:D8:6E Test IPSP node
125 # echo "connect CB:AF:14:57:D8:6E 2" > /sys/kernel/debug/bluetooth/6lowpan_control
|
| /Zephyr-Core-3.4.0/boards/arm/seeeduino_xiao/ |
| D | seeed_xiao_connector.dtsi | 22 , <8 0 &porta 7 0> /* D8 */
|
| /Zephyr-Core-3.4.0/boards/riscv/xiao_esp32c3/ |
| D | seeed_xiao_connector.dtsi | 21 <8 0 &gpio0 8 0>, /* D8 */
|
| /Zephyr-Core-3.4.0/boards/arm/xiao_ble/ |
| D | seeed_xiao_connector.dtsi | 23 , <8 0 &gpio1 13 0> /* D8 */
|
123456789
