Searched full:cm4 (Results 1 – 25 of 62) sorted by relevance
123
19 - name: cm423 - name: cm460 - mimxrt1166/cm463 - mimxrt1176/cm481 - mimxrt1166/cm484 - mimxrt1176/cm4
9 default "mimxrt1170_evkb/mimxrt1176/cm4" if $(BOARD) = "mimxrt1170_evkb"10 default "mimxrt1170_evk/mimxrt1176/cm4" if $(BOARD) = "mimxrt1170_evk"11 default "mimxrt1160_evk/mimxrt1166/cm4" if $(BOARD) = "mimxrt1160_evk"
13 default "mimxrt1160_evk/mimxrt1166/cm4" if $(BOARD) = "mimxrt1160_evk"14 default "mimxrt1170_evk/mimxrt1176/cm4" if $(BOARD) = "mimxrt1170_evk"15 default "mimxrt1170_evkb/mimxrt1176/cm4" if $(BOARD) = "mimxrt1170_evkb"
13 default "mimxrt1170_evk/mimxrt1176/cm4" if $(BOARD) = "mimxrt1170_evk"14 default "mimxrt1160_evk/mimxrt1166/cm4" if $(BOARD) = "mimxrt1160_evk"15 default "mimxrt1170_evkb/mimxrt1176/cm4" if $(BOARD) = "mimxrt1170_evkb"
27 # for the application running on the CM4 core34 # include the image header output by the CM4 image37 # Add dependency on CM4 core image to CM7 image. This way,38 # the CM4 image will be built first. This is required because the M7 image
13 default "mimxrt1170_evkb/mimxrt1176/cm4" if $(BOARD) = "mimxrt1170_evkb"14 default "mimxrt1170_evk/mimxrt1176/cm4" if $(BOARD) = "mimxrt1170_evk"15 default "mimxrt1160_evk/mimxrt1166/cm4" if $(BOARD) = "mimxrt1160_evk"
7 identifier: mimxrt1170_evk@A/mimxrt1176/cm48 name: NXP MIMXRT1170-EVK CM4
7 identifier: mimxrt1170_evk@B/mimxrt1176/cm48 name: NXP MIMXRT1170-EVKB CM4
23 …# Note: Please use JLINK above V7.50 (Only support run cm4 image when debugging due to default boo…30 board_runner_args(linkserver "--core=cm4")
7 identifier: mimxrt1160_evk/mimxrt1166/cm48 name: NXP MIMXRT1160-EVK CM4
13 # Note: Please use JLINK above V7.50 (Only support run cm4 image when debugging due to default boot…
9 * @brief System/hardware module for STM32H7 CM4 processor40 /* In case CM4 has not been forced boot by CM7, in soc_early_init_hook()41 * CM4 needs to wait until CM7 has setup clock configuration in soc_early_init_hook()
36 * then Cortex-M7 takes HSEM so that CM4 can continue running. in stm32h7_m4_wakeup()40 /* CM4 is not started at boot, start it now */ in stm32h7_m4_wakeup()
20 Used by CM4 CPU because it cannot access flash controller register to read size.21 Provides a way to configure this size when the flash controller driver runs on CM4 CPU.
6 targets stm32mp15x.cm4
8 name: NXP i.MX8MQ EVK CM4
3 # During gdb session, by default connect to CM4 core.
4 # During gdb session, by default connect to CM4 core.
8 - mimxrt1170_evk@A/mimxrt1176/cm4
98 - mimxrt1170_evk/mimxrt1176/cm4104 - mimxrt1170_evk/mimxrt1176/cm4
12 # Note: Please use JLINK above V7.50 (Only support run cm4 image when debugging due to default boot…
16 /* HW resources are split between CM7 and CM4 */
15 /* HW resources belonging to CM4 */
