Home
last modified time | relevance | path

Searched +full:5 +full:ghz (Results 1 – 25 of 76) sorted by relevance

1234

/Zephyr-latest/dts/bindings/wifi/
Dwifi-tx-power-5g.yaml6 i.e., maximum transmit power allowed for 5GHz band. Based on the
17 wifi-max-tx-pwr-5g-low-mcs0:
20 description: Maximum transmit power allowed in 5GHz band MCS0 low sub-band
21 wifi-max-tx-pwr-5g-low-mcs7:
24 description: Maximum transmit power allowed in 5GHz band MCS7 low sub-band
25 wifi-max-tx-pwr-5g-mid-mcs0:
28 description: Maximum transmit power allowed in 5GHz band MCS0 mid sub-band
29 wifi-max-tx-pwr-5g-mid-mcs7:
32 description: Maximum transmit power allowed in 5GHz band MCS7 mid sub-band
33 wifi-max-tx-pwr-5g-high-mcs0:
[all …]
/Zephyr-latest/include/zephyr/net/
Dwifi_utils.h44 * - 2: 2.4 GHz
45 * - 5: 5 GHz
46 * - 6: 6 GHz
51 * E.g. a string "2,5,6" will be converted to a bitmap value of 0x7
86 * (2: 2.4 GHz, 5: 5 GHz 6: 6 GHz) has to precede the channels in that band (e.g. 2: etc)
94 * An example channel specification specifying channels in the 2.4 GHz and 5 GHz bands is
96 * 2:1,5,7,9-11_5:36-48,100,163-167
123 * @brief Validate a channel against the 2.4 GHz band.
133 * @brief Validate a channel against the 5 GHz band.
143 * @brief Validate a channel against the 6 GHz band.
Dwifi_credentials.h31 /* this entry can use the 2.4 GHz band */
33 /* this entry can use the 5 GHz band */
38 #define WIFI_CREDENTIALS_FLAG_MFP_DISABLED BIT(5)
Dwifi.h101 /** EPA GTC security, refer to rfc3748 chapter 5. */
217 /** 2.4 GHz band. */
219 /** 5 GHz band. */
221 /** 6 GHz band (Wi-Fi 6E, also extends to 7GHz). */
342 WIFI_MODE_MESH = 5,
373 /** 802.11ax 6GHz. */
439 WIFI_SOFTAP_MODE = BIT(5),
/Zephyr-latest/drivers/wifi/nrf_wifi/
DKconfig.nrfwifi227 int "PCB loss for 2.4 GHz band"
236 int "PCB loss for 5 GHz band (5150 MHz - 5350 MHz, Channel-32 - Channel-68)"
245 int "PCB loss for 5 GHz band (5470 MHz - 5730 MHz, Channel-96 - Channel-144)"
254 int "PCB loss for 5 GHz band (5730 MHz - 5895 MHz, Channel-149 - Channel-177)"
263 int "Antenna gain for 2.4 GHz band"
268 int "Antenna gain for 5 GHz band (5150 MHz - 5350 MHz)"
273 int "Antenna gain for 5 GHz band (5470 MHz - 5730 MHz)"
278 int "Antenna gain for 5 GHz band (5730 MHz - 5895 MHz)"
283 int "DSSS Transmit power backoff (in dB) for lower edge of 2.4 GHz frequency band"
288 int "HT/VHT Transmit power backoff (in dB) for lower edge of 2.4 GHz frequency band"
[all …]
/Zephyr-latest/boards/shields/nrf7002ek/doc/
Dindex.rst13 2.4GHz and 5GHz, and is based on the nRF7002 SoC.
65 that supports only 2.4GHz Wi-Fi.
67 that supports only 2.4GHz Wi-Fi.
/Zephyr-latest/subsys/net/lib/wifi_credentials/
Dwifi_credentials_shell.c57 creds.header.bssid[3], creds.header.bssid[4], creds.header.bssid[5]); in print_network_info()
61 shell_fprintf(sh, SHELL_VT100_COLOR_DEFAULT, ", band: 2.4GHz"); in print_network_info()
65 shell_fprintf(sh, SHELL_VT100_COLOR_DEFAULT, ", band: 5GHz"); in print_network_info()
118 if (strcmp("2.4GHz", s) == 0) { in parse_band()
122 if (strcmp("5GHz", s) == 0) { in parse_band()
126 if (strcmp("6GHz", s) == 0) { in parse_band()
190 &creds.header.bssid[5]); in cmd_add_network()
262 " [{2.4GHz, 5GHz}]" in cmd_add_network()
/Zephyr-latest/dts/bindings/ieee802154/
Datmel,rf2xx.yaml45 - 5
48 is used in both Sub-Giga and 2.4GHz. It allows select channels 0-10 in
49 Sub-Giga band (0: BPSK-20, 1-10: BPSK-40) and 11-26 in 2.4GHz band
51 (0: OQPSK-SIN-RC-100, 1-10: OQPSK-SIN-250). Channel 5 is for Sub-Giga
55 5: Page 5 - OQPSK-RC-250 [0-3].
66 2.4GHz is 0x0f and 0xff for Sub-Giga. See PHY_TX_PWR at datasheet for
/Zephyr-latest/boards/shields/nrf7002eb/doc/
Dindex.rst13 2.4GHz and 5GHz, and is based on the nRF7002 SoC.
/Zephyr-latest/boards/makerdiary/nrf52840_mdk/doc/
Dindex.rst7 Bluetooth 5, Bluetooth Mesh, Thread, IEEE 802.15.4, ANT and 2.4GHz proprietary
/Zephyr-latest/drivers/wifi/nrf_wifi/src/
Dcoex.c50 /* Separate antenna configuration, WLAN in 2.4GHz. For BLE protocol. */
63 /* Separate antenna configuration, WLAN in 2.4GHz. For non BLE protocol */
76 /* Shared antenna configuration, WLAN in 2.4GHz. */
89 /* Shared/separate antennas, WLAN in 5GHz */
193 /* WLAN operating in 2.4GHz */ in nrf_wifi_coex_config_pta()
206 /* WLAN operating in 5GHz */ in nrf_wifi_coex_config_pta()
/Zephyr-latest/drivers/bluetooth/hci/
DKconfig.nxp79 wireless-connectivity/wi-fi-plus-bluetooth-plus-802-15-4/2-4-5-ghz-
80 dual-band-1x1-wi-fi-6-802-11ax-plus-bluetooth-5-4-plus-802-15-4-tri-
/Zephyr-latest/boards/waveshare/nrf51_ble400/doc/
Dindex.rst24 - Frequency range: 2.4GHz
34 - 2.4 GHz multiprotocol RF transceiver
77 5. 5V/3.3V power input/output: usually used as power output, also common-grounding with other user …
219 .. _Code samples: https://www.waveshare.com/w/upload/5/53/NRF51822-Code.7z
220 .. _Core board schematics: https://www.waveshare.com/w/upload/5/57/Core51822-Schematic.pdf
/Zephyr-latest/boards/raspberrypi/rpi_5/doc/
Dindex.rst6 `Raspberry Pi 5 product-brief`_
11 - Broadcom BCM2712 2.4GHz quad-core 64-bit Arm Cortex-A76 CPU, with cryptography extensions, 512KB …
19 - 2 x USB 3.0 ports, supporting simultaneous 5Gbps operation
24 - 5V/5A DC power via USB-C, with Power Delivery support
32 The Raspberry Pi 5 board configuration supports the following hardware features:
69 * `bcm2712-rpi-5.dtb`_
70 3. Insert the Micro SD card and power on the Raspberry Pi 5.
72 then, You will see the Raspberry Pi 5 running the :file:`zephyr.bin`.
96 Insert the Micro SD card and power on the Raspberry Pi 5. And then, the STAT LED will start to blin…
110 Use the JST cable to connect the Raspberry Pi Debug Probe UART port to the Raspberry Pi 5 UART port…
[all …]
/Zephyr-latest/drivers/wifi/nxp/
DKconfig.nxp54 …nnectivity/wi-fi-plus-bluetooth-plus-802-15-4/2-4-5-ghz-dual-band-1x1-wi-fi-5-802-11ac-plus-blueto…
62 …nnectivity/wi-fi-plus-bluetooth-plus-802-15-4/2-4-5-ghz-dual-band-1x1-wi-fi-4-802-11n-plus-bluetoo…
70 …nnectivity/wi-fi-plus-bluetooth-plus-802-15-4/2-4-5ghz-dual-band-1x1-wi-fi-6-802-11ax-plus-bluetoo…
71 …nnectivity/wi-fi-plus-bluetooth-plus-802-15-4/2-4-5-ghz-dual-band-1x1-wi-fi-6-802-11ax-plus-blueto…
79 …https://www.nxp.com/products/wireless-connectivity/wi-fi-plus-bluetooth-plus-802-15-4/2-4-ghz-sing…
683 bool "5GHz Support(Band A)"
687 This option enables the use of 5GHz.
/Zephyr-latest/boards/st/stm32wb5mm_dk/doc/
Dstm32wb5mm_dk.rst19 - 2.4 GHz RF transceiver
38 - 5 V delivered by:
52 STM32WB5MMG is an ultra-low-power and small form factor certified 2.4 GHz
66 - 2.4GHz
91 - Internal low-power 32 kHz (±5%) RC (LSI1)
/Zephyr-latest/boards/st/stm32wb5mmg/doc/
Dstm32wb5mmg.rst6 STM32WB5MMG is an ultra-low-power and small form factor certified 2.4 GHz
38 STM32WB5MMG is an ultra-low-power and small form factor certified 2.4 GHz
52 - 2.4GHz
80 - Internal low-power 32 kHz (±5%) RC (LSI1)
106 - Up to 72 fast I/Os, 70 of them 5 V-tolerant
284 Device found: CE:5B:9A:87:69:4F (random) (RSSI -80), type 3, AD data len 8
/Zephyr-latest/boards/96boards/avenger96/doc/
Dindex.rst26 - WiFi: 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac
117 - MIPI® DSI 2 data lanes up to 1 GHz each
125 - 5 × 16-bit low-power timers
/Zephyr-latest/drivers/ieee802154/
Dieee802154_cc13xx_cc26xx.c47 /* 2.4 GHz power table */
51 {-10, RF_TxPowerTable_DEFAULT_PA_ENTRY(15, 3, 0, 5)},
52 {-5, RF_TxPowerTable_DEFAULT_PA_ENTRY(22, 3, 0, 9)},
58 {5, RF_TxPowerTable_DEFAULT_PA_ENTRY(23, 0, 0, 57)},
164 *frequency = 2405 + 5 * (channel - 11); in ieee802154_cc13xx_cc26xx_channel_to_frequency()
168 /* TODO: Support sub-GHz for CC13xx rather than having separate drivers */ in ieee802154_cc13xx_cc26xx_channel_to_frequency()
279 /* TODO Support sub-GHz for CC13xx */ in ieee802154_cc13xx_cc26xx_set_txpower()
326 if (drv_data->saved_cmdhandle >= BIT(12) - 5) { in ieee802154_cc13xx_cc26xx_tx()
489 * Stops the sub-GHz interface and yields the radio (tells RF module to power
Dieee802154_cc13xx_cc26xx_subg.c54 /* Radio register overrides for CC13x2R (note: CC26x2 does not support sub-GHz radio)
171 .loDivider = 5,
181 /* Sub GHz power tables */
189 { -10, RF_TxPowerTable_DEFAULT_PA_ENTRY(2, 3, 0, 5) },
190 { -5, RF_TxPowerTable_DEFAULT_PA_ENTRY(4, 3, 0, 5) },
196 { 5, RF_TxPowerTable_DEFAULT_PA_ENTRY(14, 3, 0, 14) },
211 /* Sub GHz power table */
215 { -10, RF_TxPowerTable_DEFAULT_PA_ENTRY(2, 3, 0, 5) },
216 { -5, RF_TxPowerTable_DEFAULT_PA_ENTRY(4, 3, 0, 5) },
222 { 5, RF_TxPowerTable_DEFAULT_PA_ENTRY(14, 3, 0, 14) },
[all …]
/Zephyr-latest/boards/st/nucleo_wb55rg/doc/
Dnucleo_wb55rg.rst12 - 2.4 GHz RF transceiver supporting Bluetooth® specification v5.0 and
35 with 1 Mbyte of Flash memory, Bluetooth 5, 802.15.4, USB, LCD, AES-256 SoC and
42 - 2.4GHz
43 - RF transceiver supporting Bluetooth® 5 specification, IEEE 802.15.4-2011 PHY and MAC,
59 - 2x Internal low-power 32 kHz RC (|plusminus| 5% and |plusminus| 500ppm)
70 - 2x 32-bit and 5x 16-bit general purpose
76 - Up to 114 fast I/Os, most 5 V-tolerant, up to 14 I/Os with independent supply down to 1.08 V
125 - 64-bit unique ID. Possibility to derive 802.15.5 64-bit and
128 - Up to 72 fast I/Os, 70 of them 5 V-tolerant
/Zephyr-latest/boards/ti/cc3235sf_launchxl/doc/
Dindex.rst8 security features. It supports 802.11 a/b/g/n, both 2.4 GHz and 5 GHz.
107 in the `CC32xx Quick Start Guide`_, except for steps 5 and 6 in
/Zephyr-latest/boards/toradex/verdin_imx8mm/doc/
Dindex.rst11 backwards compatibility with 32-bit Armv7-A software. The main cores run at up to 1.8 GHz for
12 commercial graded products and 1.6 GHz for industrial temperature range products.
29 - WiFi Dual-band 802.11 ac/a/b/g/n 2.4/5 GHz
30 - Bluetooth 5/BLE
/Zephyr-latest/boards/st/nucleo_wba52cg/doc/
Dnucleo_wba52cg.rst20 - 2.4 GHz RF transceiver supporting Bluetooth® specification v5.3
51 - 2.4 GHz radio
86 - Internal low-power 32 kHz (±5%) RC
134 - Up to 35 I/Os (most of them 5 V-tolerant) with interrupt capability
/Zephyr-latest/boards/luatos/esp32s3_luatos_core/doc/
Dindex.rst10 The board comes equipped with a 2.4GHz antenna and supports both Wi-Fi and Bluetooth functionalitie…
20 ESP32-S3 is a low-power MCU-based system on a chip (SoC) with integrated 2.4 GHz Wi-Fi
52 - General DMA controller (GDMA), with 5 transmit channels and 5 receive channels

1234