1 /* 2 * Copyright (c) 2019, The OpenThread Authors. 3 * All rights reserved. 4 * 5 * Redistribution and use in source and binary forms, with or without 6 * modification, are permitted provided that the following conditions are met: 7 * 1. Redistributions of source code must retain the above copyright 8 * notice, this list of conditions and the following disclaimer. 9 * 2. Redistributions in binary form must reproduce the above copyright 10 * notice, this list of conditions and the following disclaimer in the 11 * documentation and/or other materials provided with the distribution. 12 * 3. Neither the name of the copyright holder nor the 13 * names of its contributors may be used to endorse or promote products 14 * derived from this software without specific prior written permission. 15 * 16 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 17 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 18 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 19 * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE 20 * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 21 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 22 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 23 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 24 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 25 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 26 * POSSIBILITY OF SUCH DAMAGE. 27 */ 28 29 /** 30 * @file 31 * This file includes compile-time configurations for Border Router services. 32 * 33 */ 34 35 #ifndef CONFIG_BORDER_ROUTER_H_ 36 #define CONFIG_BORDER_ROUTER_H_ 37 38 #include <config/border_routing.h> 39 40 /** 41 * @def OPENTHREAD_CONFIG_BORDER_ROUTER_ENABLE 42 * 43 * Define to 1 to enable Border Router support. 44 * 45 */ 46 #ifndef OPENTHREAD_CONFIG_BORDER_ROUTER_ENABLE 47 #define OPENTHREAD_CONFIG_BORDER_ROUTER_ENABLE 0 48 #endif 49 50 /** 51 * @def OPENTHREAD_CONFIG_BORDER_ROUTER_REQUEST_ROUTER_ROLE 52 * 53 * Define to 1 to enable mechanism on a Border Router which provides IP connectivity to request router role upgrade. 54 * 55 * This config is applicable on an `OPENTHREAD_FTD` build and when `OPENTHREAD_CONFIG_BORDER_ROUTER_ENABLE` is also 56 * enabled. 57 * 58 * A Border Router is considered to provide external IP connectivity if at least one of the below conditions hold: 59 * 60 * - It has added at least one external route entry. 61 * - It has added at least one prefix entry with default-route and on-mesh flags set. 62 * - It has added at least one domain prefix (domain and on-mesh flags set). 63 * 64 * A Border Router which provides IP connectivity and is acting as a REED is eligible to request a router role upgrade 65 * by sending an "Address Solicit" request to leader with status reason `BorderRouterRequest`. This reason is used when 66 * the number of active routers in the Thread mesh is above the threshold, and only if the number of existing eligible 67 * BRs (determined from the Thread Network Data) that are acting as router is less than two. This mechanism allows up 68 * to two eligible Border Routers to request router role upgrade when the number of routers is already above the 69 * threshold. 70 * 71 */ 72 #ifndef OPENTHREAD_CONFIG_BORDER_ROUTER_REQUEST_ROUTER_ROLE 73 #define OPENTHREAD_CONFIG_BORDER_ROUTER_REQUEST_ROUTER_ROLE 1 74 #endif 75 76 /** 77 * @def OPENTHREAD_CONFIG_BORDER_ROUTER_SIGNAL_NETWORK_DATA_FULL 78 * 79 * Define as 1 to enable mechanism to detect and signal when local or leader Network Data gets full. 80 * 81 */ 82 #ifndef OPENTHREAD_CONFIG_BORDER_ROUTER_SIGNAL_NETWORK_DATA_FULL 83 #define OPENTHREAD_CONFIG_BORDER_ROUTER_SIGNAL_NETWORK_DATA_FULL OPENTHREAD_CONFIG_BORDER_ROUTING_ENABLE 84 #endif 85 86 #endif // CONFIG_BORDER_ROUTER_H_ 87
