/* * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/ * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * * Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the * distribution. * * Neither the name of Texas Instruments Incorporated nor the names of * its contributors may be used to endorse or promote products derived * from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * */ //***************************************************************************** // // timer.c // // Driver for the timer module. // //***************************************************************************** //***************************************************************************** // //! \addtogroup GPT_General_Purpose_Timer_api //! @{ // //***************************************************************************** #include "inc/hw_ints.h" #include "inc/hw_memmap.h" #include "inc/hw_timer.h" #include "inc/hw_types.h" #include "debug.h" #include "interrupt.h" #include "timer.h" //***************************************************************************** // //! \internal //! Checks a timer base address. //! //! \param ulBase is the base address of the timer module. //! //! This function determines if a timer module base address is valid. //! //! \return Returns \b true if the base address is valid and \b false //! otherwise. // //***************************************************************************** #ifdef DEBUG static tBoolean TimerBaseValid(unsigned long ulBase) { return((ulBase == TIMERA0_BASE) || (ulBase == TIMERA1_BASE) || (ulBase == TIMERA2_BASE) || (ulBase == TIMERA3_BASE)); } #endif //***************************************************************************** // //! Enables the timer(s). //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer(s) to enable; must be one of \b TIMER_A, //! \b TIMER_B, or \b TIMER_BOTH. //! //! This function enables operation of the timer module. The timer must be //! configured before it is enabled. //! //! \return None. // //***************************************************************************** void TimerEnable(unsigned long ulBase, unsigned long ulTimer) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B) || (ulTimer == TIMER_BOTH)); // // Enable the timer(s) module. // HWREG(ulBase + TIMER_O_CTL) |= ulTimer & (TIMER_CTL_TAEN | TIMER_CTL_TBEN); } //***************************************************************************** // //! Disables the timer(s). //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer(s) to disable; must be one of //! \b TIMER_A, \b TIMER_B, or \b TIMER_BOTH. //! //! This function disables operation of the timer module. //! //! \return None. // //***************************************************************************** void TimerDisable(unsigned long ulBase, unsigned long ulTimer) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B) || (ulTimer == TIMER_BOTH)); // // Disable the timer module. // HWREG(ulBase + TIMER_O_CTL) &= ~(ulTimer & (TIMER_CTL_TAEN | TIMER_CTL_TBEN)); } //***************************************************************************** // //! Configures the timer(s). //! //! \param ulBase is the base address of the timer module. //! \param ulConfig is the configuration for the timer. //! //! This function configures the operating mode of the timer(s). The timer //! module is disabled before being configured, and is left in the disabled //! state. The 16/32-bit timer is comprised of two 16-bit timers that can //! operate independently or be concatenated to form a 32-bit timer. //! //! The configuration is specified in \e ulConfig as one of the following //! values: //! //! - \b TIMER_CFG_ONE_SHOT - Full-width one-shot timer //! - \b TIMER_CFG_ONE_SHOT_UP - Full-width one-shot timer that counts up //! instead of down (not available on all parts) //! - \b TIMER_CFG_PERIODIC - Full-width periodic timer //! - \b TIMER_CFG_PERIODIC_UP - Full-width periodic timer that counts up //! instead of down (not available on all parts) //! - \b TIMER_CFG_SPLIT_PAIR - Two half-width timers //! //! When configured for a pair of half-width timers, each timer is separately //! configured. The first timer is configured by setting \e ulConfig to //! the result of a logical OR operation between one of the following values //! and \e ulConfig: //! //! - \b TIMER_CFG_A_ONE_SHOT - Half-width one-shot timer //! - \b TIMER_CFG_A_ONE_SHOT_UP - Half-width one-shot timer that counts up //! instead of down (not available on all parts) //! - \b TIMER_CFG_A_PERIODIC - Half-width periodic timer //! - \b TIMER_CFG_A_PERIODIC_UP - Half-width periodic timer that counts up //! instead of down (not available on all parts) //! - \b TIMER_CFG_A_CAP_COUNT - Half-width edge count capture //! - \b TIMER_CFG_A_CAP_TIME - Half-width edge time capture //! - \b TIMER_CFG_A_PWM - Half-width PWM output //! //! Similarly, the second timer is configured by setting \e ulConfig to //! the result of a logical OR operation between one of the corresponding //! \b TIMER_CFG_B_* values and \e ulConfig. //! //! \return None. // //***************************************************************************** void TimerConfigure(unsigned long ulBase, unsigned long ulConfig) { ASSERT( (ulConfig == TIMER_CFG_ONE_SHOT) || (ulConfig == TIMER_CFG_ONE_SHOT_UP) || (ulConfig == TIMER_CFG_PERIODIC) || (ulConfig == TIMER_CFG_PERIODIC_UP) || (((ulConfig & 0xff000000) == TIMER_CFG_SPLIT_PAIR) && ((((ulConfig & 0x000000ff) == TIMER_CFG_A_ONE_SHOT) || ((ulConfig & 0x000000ff) == TIMER_CFG_A_ONE_SHOT_UP) || ((ulConfig & 0x000000ff) == TIMER_CFG_A_PERIODIC) || ((ulConfig & 0x000000ff) == TIMER_CFG_A_PERIODIC_UP) || ((ulConfig & 0x000000ff) == TIMER_CFG_A_CAP_COUNT) || ((ulConfig & 0x000000ff) == TIMER_CFG_A_CAP_TIME) || ((ulConfig & 0x000000ff) == TIMER_CFG_A_PWM)) || (((ulConfig & 0x0000ff00) == TIMER_CFG_B_ONE_SHOT) || ((ulConfig & 0x0000ff00) == TIMER_CFG_B_ONE_SHOT_UP) || ((ulConfig & 0x0000ff00) == TIMER_CFG_B_PERIODIC) || ((ulConfig & 0x0000ff00) == TIMER_CFG_B_PERIODIC_UP) || ((ulConfig & 0x0000ff00) == TIMER_CFG_B_CAP_COUNT) || ((ulConfig & 0x0000ff00) == TIMER_CFG_B_CAP_TIME) || ((ulConfig & 0x0000ff00) == TIMER_CFG_B_PWM))))); // // Enable CCP to IO path // HWREG(0x440260B0) = 0xFF; // // Disable the timers. // HWREG(ulBase + TIMER_O_CTL) &= ~(TIMER_CTL_TAEN | TIMER_CTL_TBEN); // // Set the global timer configuration. // HWREG(ulBase + TIMER_O_CFG) = ulConfig >> 24; // // Set the configuration of the A and B timers. Note that the B timer // configuration is ignored by the hardware in 32-bit modes. // HWREG(ulBase + TIMER_O_TAMR) = ulConfig & 255; HWREG(ulBase + TIMER_O_TBMR) = (ulConfig >> 8) & 255; } //***************************************************************************** // //! Controls the output level. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer(s) to adjust; must be one of \b TIMER_A, //! \b TIMER_B, or \b TIMER_BOTH. //! \param bInvert specifies the output level. //! //! This function sets the PWM output level for the specified timer. If the //! \e bInvert parameter is \b true, then the timer's output is made active //! low; otherwise, it is made active high. //! //! \return None. // //***************************************************************************** void TimerControlLevel(unsigned long ulBase, unsigned long ulTimer, tBoolean bInvert) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B) || (ulTimer == TIMER_BOTH)); // // Set the output levels as requested. // ulTimer &= TIMER_CTL_TAPWML | TIMER_CTL_TBPWML; HWREG(ulBase + TIMER_O_CTL) = (bInvert ? (HWREG(ulBase + TIMER_O_CTL) | ulTimer) : (HWREG(ulBase + TIMER_O_CTL) & ~(ulTimer))); } //***************************************************************************** // //! Controls the event type. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer(s) to be adjusted; must be one of //! \b TIMER_A, \b TIMER_B, or \b TIMER_BOTH. //! \param ulEvent specifies the type of event; must be one of //! \b TIMER_EVENT_POS_EDGE, \b TIMER_EVENT_NEG_EDGE, or //! \b TIMER_EVENT_BOTH_EDGES. //! //! This function sets the signal edge(s) that triggers the timer when in //! capture mode. //! //! \return None. // //***************************************************************************** void TimerControlEvent(unsigned long ulBase, unsigned long ulTimer, unsigned long ulEvent) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B) || (ulTimer == TIMER_BOTH)); // // Set the event type. // ulEvent &= ulTimer & (TIMER_CTL_TAEVENT_M | TIMER_CTL_TBEVENT_M); HWREG(ulBase + TIMER_O_CTL) = ((HWREG(ulBase + TIMER_O_CTL) & ~(TIMER_CTL_TAEVENT_M | TIMER_CTL_TBEVENT_M)) | ulEvent); } //***************************************************************************** // //! Controls the stall handling. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer(s) to be adjusted; must be one of //! \b TIMER_A, \b TIMER_B, or \b TIMER_BOTH. //! \param bStall specifies the response to a stall signal. //! //! This function controls the stall response for the specified timer. If the //! \e bStall parameter is \b true, then the timer stops counting if the //! processor enters debug mode; otherwise the timer keeps running while in //! debug mode. //! //! \return None. // //***************************************************************************** void TimerControlStall(unsigned long ulBase, unsigned long ulTimer, tBoolean bStall) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B) || (ulTimer == TIMER_BOTH)); // // Set the stall mode. // ulTimer &= TIMER_CTL_TASTALL | TIMER_CTL_TBSTALL; HWREG(ulBase + TIMER_O_CTL) = (bStall ? (HWREG(ulBase + TIMER_O_CTL) | ulTimer) : (HWREG(ulBase + TIMER_O_CTL) & ~(ulTimer))); } //***************************************************************************** // //! Set the timer prescale value. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer(s) to adjust; must be one of \b TIMER_A, //! \b TIMER_B, or \b TIMER_BOTH. //! \param ulValue is the timer prescale value which must be between 0 and 255 //! (inclusive) for 16/32-bit timers. //! //! This function sets the value of the input clock prescaler. The prescaler //! is only operational when in half-width mode and is used to extend the range //! of the half-width timer modes. //! //! \return None. // //***************************************************************************** void TimerPrescaleSet(unsigned long ulBase, unsigned long ulTimer, unsigned long ulValue) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B) || (ulTimer == TIMER_BOTH)); ASSERT(ulValue < 256); // // Set the timer A prescaler if requested. // if(ulTimer & TIMER_A) { HWREG(ulBase + TIMER_O_TAPR) = ulValue; } // // Set the timer B prescaler if requested. // if(ulTimer & TIMER_B) { HWREG(ulBase + TIMER_O_TBPR) = ulValue; } } //***************************************************************************** // //! Get the timer prescale value. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer; must be one of \b TIMER_A or //! \b TIMER_B. //! //! This function gets the value of the input clock prescaler. The prescaler //! is only operational when in half-width mode and is used to extend the range //! of the half-width timer modes. //! //! \return The value of the timer prescaler. // //***************************************************************************** unsigned long TimerPrescaleGet(unsigned long ulBase, unsigned long ulTimer) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B) || (ulTimer == TIMER_BOTH)); // // Return the appropriate prescale value. // return((ulTimer == TIMER_A) ? HWREG(ulBase + TIMER_O_TAPR) : HWREG(ulBase + TIMER_O_TBPR)); } //***************************************************************************** // //! Set the timer prescale match value. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer(s) to adjust; must be one of \b TIMER_A, //! \b TIMER_B, or \b TIMER_BOTH. //! \param ulValue is the timer prescale match value which must be between 0 //! and 255 (inclusive) for 16/32-bit timers. //! //! This function sets the value of the input clock prescaler match value. //! When in a half-width mode that uses the counter match and the prescaler, //! the prescale match effectively extends the range of the match. //! //! \note The availability of the prescaler match varies with the //! part and timer mode in use. Please consult the datasheet for the part you //! are using to determine whether this support is available. //! //! \return None. // //***************************************************************************** void TimerPrescaleMatchSet(unsigned long ulBase, unsigned long ulTimer, unsigned long ulValue) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B) || (ulTimer == TIMER_BOTH)); ASSERT(ulValue < 256); // // Set the timer A prescale match if requested. // if(ulTimer & TIMER_A) { HWREG(ulBase + TIMER_O_TAPMR) = ulValue; } // // Set the timer B prescale match if requested. // if(ulTimer & TIMER_B) { HWREG(ulBase + TIMER_O_TBPMR) = ulValue; } } //***************************************************************************** // //! Get the timer prescale match value. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer; must be one of \b TIMER_A or //! \b TIMER_B. //! //! This function gets the value of the input clock prescaler match value. //! When in a half-width mode that uses the counter match and prescaler, the //! prescale match effectively extends the range of the match. //! //! \note The availability of the prescaler match varies with the //! part and timer mode in use. Please consult the datasheet for the part you //! are using to determine whether this support is available. //! //! \return The value of the timer prescale match. // //***************************************************************************** unsigned long TimerPrescaleMatchGet(unsigned long ulBase, unsigned long ulTimer) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B) || (ulTimer == TIMER_BOTH)); // // Return the appropriate prescale match value. // return((ulTimer == TIMER_A) ? HWREG(ulBase + TIMER_O_TAPMR) : HWREG(ulBase + TIMER_O_TBPMR)); } //***************************************************************************** // //! Sets the timer load value. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer(s) to adjust; must be one of \b TIMER_A, //! \b TIMER_B, or \b TIMER_BOTH. Only \b TIMER_A should be used when the //! timer is configured for full-width operation. //! \param ulValue is the load value. //! //! This function sets the timer load value; if the timer is running then the //! value is immediately loaded into the timer. //! //! \note This function can be used for both full- and half-width modes of //! 16/32-bit timers. //! //! \return None. // //***************************************************************************** void TimerLoadSet(unsigned long ulBase, unsigned long ulTimer, unsigned long ulValue) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B) || (ulTimer == TIMER_BOTH)); // // Set the timer A load value if requested. // if(ulTimer & TIMER_A) { HWREG(ulBase + TIMER_O_TAILR) = ulValue; } // // Set the timer B load value if requested. // if(ulTimer & TIMER_B) { HWREG(ulBase + TIMER_O_TBILR) = ulValue; } } //***************************************************************************** // //! Gets the timer load value. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer; must be one of \b TIMER_A or //! \b TIMER_B. Only \b TIMER_A should be used when the timer is configured //! for full-width operation. //! //! This function gets the currently programmed interval load value for the //! specified timer. //! //! \note This function can be used for both full- and half-width modes of //! 16/32-bit timers. //! //! \return Returns the load value for the timer. // //***************************************************************************** unsigned long TimerLoadGet(unsigned long ulBase, unsigned long ulTimer) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B)); // // Return the appropriate load value. // return((ulTimer == TIMER_A) ? HWREG(ulBase + TIMER_O_TAILR) : HWREG(ulBase + TIMER_O_TBILR)); } //***************************************************************************** // //! Gets the current timer value. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer; must be one of \b TIMER_A or //! \b TIMER_B. Only \b TIMER_A should be used when the timer is configured //! for 32-bit operation. //! //! This function reads the current value of the specified timer. //! //! \return Returns the current value of the timer. // //***************************************************************************** unsigned long TimerValueGet(unsigned long ulBase, unsigned long ulTimer) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B)); // // Return the appropriate timer value. // return((ulTimer == TIMER_A) ? HWREG(ulBase + TIMER_O_TAR) : HWREG(ulBase + TIMER_O_TBR)); } //***************************************************************************** // //! Sets the current timer value. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer; must be one of \b TIMER_A or //! \b TIMER_B. Only \b TIMER_A should be used when the timer is configured //! for 32-bit operation. //! \param ulValue is the new value of the timer to be set. //! //! This function sets the current value of the specified timer. //! //! \return None. // //***************************************************************************** void TimerValueSet(unsigned long ulBase, unsigned long ulTimer, unsigned long ulValue) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B)); // // Set the appropriate timer value. // if(ulTimer == TIMER_A) { HWREG(ulBase + TIMER_O_TAV) = ulValue; } else { HWREG(ulBase + TIMER_O_TBV) = ulValue; } } //***************************************************************************** // //! Sets the timer match value. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer(s) to adjust; must be one of \b TIMER_A, //! \b TIMER_B, or \b TIMER_BOTH. Only \b TIMER_A should be used when the //! timer is configured for 32-bit operation. //! \param ulValue is the match value. //! //! This function sets the match value for a timer. This is used in capture //! count mode to determine when to interrupt the processor and in PWM mode to //! determine the duty cycle of the output signal. //! //! \return None. // //***************************************************************************** void TimerMatchSet(unsigned long ulBase, unsigned long ulTimer, unsigned long ulValue) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B) || (ulTimer == TIMER_BOTH)); // // Set the timer A match value if requested. // if(ulTimer & TIMER_A) { HWREG(ulBase + TIMER_O_TAMATCHR) = ulValue; } // // Set the timer B match value if requested. // if(ulTimer & TIMER_B) { HWREG(ulBase + TIMER_O_TBMATCHR) = ulValue; } } //***************************************************************************** // //! Gets the timer match value. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer; must be one of \b TIMER_A or //! \b TIMER_B. Only \b TIMER_A should be used when the timer is configured //! for 32-bit operation. //! //! This function gets the match value for the specified timer. //! //! \return Returns the match value for the timer. // //******************************************************************************** unsigned long TimerMatchGet(unsigned long ulBase, unsigned long ulTimer) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B)); // // Return the appropriate match value. // return((ulTimer == TIMER_A) ? HWREG(ulBase + TIMER_O_TAMATCHR) : HWREG(ulBase + TIMER_O_TBMATCHR)); } //***************************************************************************** // //! Registers an interrupt handler for the timer interrupt. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer(s); must be one of \b TIMER_A, //! \b TIMER_B, or \b TIMER_BOTH. //! \param pfnHandler is a pointer to the function to be called when the timer //! interrupt occurs. //! //! This function sets the handler to be called when a timer interrupt occurs. //! In addition, this function enables the global interrupt in the interrupt //! controller; specific timer interrupts must be enabled via TimerIntEnable(). //! It is the interrupt handler's responsibility to clear the interrupt source //! via TimerIntClear(). //! //! \sa IntRegister() for important information about registering interrupt //! handlers. //! //! \return None. // //***************************************************************************** void TimerIntRegister(unsigned long ulBase, unsigned long ulTimer, void (*pfnHandler)(void)) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B) || (ulTimer == TIMER_BOTH)); ulBase = ((ulBase == TIMERA0_BASE) ? INT_TIMERA0A : ((ulBase == TIMERA1_BASE) ? INT_TIMERA1A : ((ulBase == TIMERA2_BASE) ? INT_TIMERA2A : INT_TIMERA3A))); // // Register an interrupt handler for timer A if requested. // if(ulTimer & TIMER_A) { // // Register the interrupt handler. // IntRegister(ulBase, pfnHandler); // // Enable the interrupt. // IntEnable(ulBase); } // // Register an interrupt handler for timer B if requested. // if(ulTimer & TIMER_B) { // // Register the interrupt handler. // IntRegister(ulBase + 1, pfnHandler); // // Enable the interrupt. // IntEnable(ulBase + 1); } } //***************************************************************************** // //! Unregisters an interrupt handler for the timer interrupt. //! //! \param ulBase is the base address of the timer module. //! \param ulTimer specifies the timer(s); must be one of \b TIMER_A, //! \b TIMER_B, or \b TIMER_BOTH. //! //! This function clears the handler to be called when a timer interrupt //! occurs. This function also masks off the interrupt in the interrupt //! controller so that the interrupt handler no longer is called. //! //! \sa IntRegister() for important information about registering interrupt //! handlers. //! //! \return None. // //***************************************************************************** void TimerIntUnregister(unsigned long ulBase, unsigned long ulTimer) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); ASSERT((ulTimer == TIMER_A) || (ulTimer == TIMER_B) || (ulTimer == TIMER_BOTH)); // // Get the interrupt number for this timer module. // ulBase = ((ulBase == TIMERA0_BASE) ? INT_TIMERA0A : ((ulBase == TIMERA1_BASE) ? INT_TIMERA1A : ((ulBase == TIMERA2_BASE) ? INT_TIMERA2A : INT_TIMERA3A))); // // Unregister the interrupt handler for timer A if requested. // if(ulTimer & TIMER_A) { // // Disable the interrupt. // IntDisable(ulBase); // // Unregister the interrupt handler. // IntUnregister(ulBase); } // // Unregister the interrupt handler for timer B if requested. // if(ulTimer & TIMER_B) { // // Disable the interrupt. // IntDisable(ulBase + 1); // // Unregister the interrupt handler. // IntUnregister(ulBase + 1); } } //***************************************************************************** // //! Enables individual timer interrupt sources. //! //! \param ulBase is the base address of the timer module. //! \param ulIntFlags is the bit mask of the interrupt sources to be enabled. //! //! Enables the indicated timer interrupt sources. Only the sources that are //! enabled can be reflected to the processor interrupt; disabled sources have //! no effect on the processor. //! //! The \e ulIntFlags parameter must be the logical OR of any combination of //! the following: //! //! - \b TIMER_CAPB_EVENT - Capture B event interrupt //! - \b TIMER_CAPB_MATCH - Capture B match interrupt //! - \b TIMER_TIMB_TIMEOUT - Timer B timeout interrupt //! - \b TIMER_CAPA_EVENT - Capture A event interrupt //! - \b TIMER_CAPA_MATCH - Capture A match interrupt //! - \b TIMER_TIMA_TIMEOUT - Timer A timeout interrupt //! //! \return None. // //***************************************************************************** void TimerIntEnable(unsigned long ulBase, unsigned long ulIntFlags) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); // // Enable the specified interrupts. // HWREG(ulBase + TIMER_O_IMR) |= ulIntFlags; } //***************************************************************************** // //! Disables individual timer interrupt sources. //! //! \param ulBase is the base address of the timer module. //! \param ulIntFlags is the bit mask of the interrupt sources to be disabled. //! //! Disables the indicated timer interrupt sources. Only the sources that are //! enabled can be reflected to the processor interrupt; disabled sources have //! no effect on the processor. //! //! The \e ulIntFlags parameter has the same definition as the \e ulIntFlags //! parameter to TimerIntEnable(). //! //! \return None. // //***************************************************************************** void TimerIntDisable(unsigned long ulBase, unsigned long ulIntFlags) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); // // Disable the specified interrupts. // HWREG(ulBase + TIMER_O_IMR) &= ~(ulIntFlags); } //***************************************************************************** // //! Gets the current interrupt status. //! //! \param ulBase is the base address of the timer module. //! \param bMasked is false if the raw interrupt status is required and true if //! the masked interrupt status is required. //! //! This function returns the interrupt status for the timer module. Either //! the raw interrupt status or the status of interrupts that are allowed to //! reflect to the processor can be returned. //! //! \return The current interrupt status, enumerated as a bit field of //! values described in TimerIntEnable(). // //***************************************************************************** unsigned long TimerIntStatus(unsigned long ulBase, tBoolean bMasked) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); // // Return either the interrupt status or the raw interrupt status as // requested. // return(bMasked ? HWREG(ulBase + TIMER_O_MIS) : HWREG(ulBase + TIMER_O_RIS)); } //***************************************************************************** // //! Clears timer interrupt sources. //! //! \param ulBase is the base address of the timer module. //! \param ulIntFlags is a bit mask of the interrupt sources to be cleared. //! //! The specified timer interrupt sources are cleared, so that they no longer //! assert. This function must be called in the interrupt handler to keep the //! interrupt from being triggered again immediately upon exit. //! //! The \e ulIntFlags parameter has the same definition as the \e ulIntFlags //! parameter to TimerIntEnable(). //! //! \note Because there is a write buffer in the Cortex-M3 processor, it may //! take several clock cycles before the interrupt source is actually cleared. //! Therefore, it is recommended that the interrupt source be cleared early in //! the interrupt handler (as opposed to the very last action) to avoid //! returning from the interrupt handler before the interrupt source is //! actually cleared. Failure to do so may result in the interrupt handler //! being immediately reentered (because the interrupt controller still sees //! the interrupt source asserted). //! //! \return None. // //***************************************************************************** void TimerIntClear(unsigned long ulBase, unsigned long ulIntFlags) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); // // Clear the requested interrupt sources. // HWREG(ulBase + TIMER_O_ICR) = ulIntFlags; } //***************************************************************************** // //! Enables the events that can trigger a DMA request. //! //! \param ulBase is the base address of the timer module. //! \param ulDMAEvent is a bit mask of the events that can trigger DMA. //! //! This function enables the timer events that can trigger the start of a DMA //! sequence. The DMA trigger events are specified in the \e ui32DMAEvent //! parameter by passing in the logical OR of the following values: //! //! - \b TIMER_DMA_MODEMATCH_B - The mode match DMA trigger for timer B is //! enabled. //! - \b TIMER_DMA_CAPEVENT_B - The capture event DMA trigger for timer B is //! enabled. //! - \b TIMER_DMA_CAPMATCH_B - The capture match DMA trigger for timer B is //! enabled. //! - \b TIMER_DMA_TIMEOUT_B - The timeout DMA trigger for timer B is enabled. //! - \b TIMER_DMA_MODEMATCH_A - The mode match DMA trigger for timer A is //! enabled. //! - \b TIMER_DMA_CAPEVENT_A - The capture event DMA trigger for timer A is //! enabled. //! - \b TIMER_DMA_CAPMATCH_A - The capture match DMA trigger for timer A is //! enabled. //! - \b TIMER_DMA_TIMEOUT_A - The timeout DMA trigger for timer A is enabled. //! //! \return None. // //***************************************************************************** void TimerDMAEventSet(unsigned long ulBase, unsigned long ulDMAEvent) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); // // Set the DMA triggers. // HWREG(ulBase + TIMER_O_DMAEV) = ulDMAEvent; } //***************************************************************************** // //! Returns the events that can trigger a DMA request. //! //! \param ulBase is the base address of the timer module. //! //! This function returns the timer events that can trigger the start of a DMA //! sequence. The DMA trigger events are the logical OR of the following //! values: //! //! - \b TIMER_DMA_MODEMATCH_B - Enables the mode match DMA trigger for timer //! B. //! - \b TIMER_DMA_CAPEVENT_B - Enables the capture event DMA trigger for //! timer B. //! - \b TIMER_DMA_CAPMATCH_B - Enables the capture match DMA trigger for //! timer B. //! - \b TIMER_DMA_TIMEOUT_B - Enables the timeout DMA trigger for timer B. //! - \b TIMER_DMA_MODEMATCH_A - Enables the mode match DMA trigger for timer //! A. //! - \b TIMER_DMA_CAPEVENT_A - Enables the capture event DMA trigger for //! timer A. //! - \b TIMER_DMA_CAPMATCH_A - Enables the capture match DMA trigger for //! timer A. //! - \b TIMER_DMA_TIMEOUT_A - Enables the timeout DMA trigger for timer A. //! //! \return The timer events that trigger the uDMA. // //***************************************************************************** unsigned long TimerDMAEventGet(unsigned long ulBase) { // // Check the arguments. // ASSERT(TimerBaseValid(ulBase)); // // Return the current DMA triggers. // return(HWREG(ulBase + TIMER_O_DMAEV)); } //***************************************************************************** // // Close the Doxygen group. //! @} // //*****************************************************************************