/** ****************************************************************************** * @file stm32g4xx_hal_lptim.c * @author MCD Application Team * @brief LPTIM HAL module driver. * This file provides firmware functions to manage the following * functionalities of the Low Power Timer (LPTIM) peripheral: * + Initialization and de-initialization functions. * + Start/Stop operation functions in polling mode. * + Start/Stop operation functions in interrupt mode. * + Reading operation functions. * + Peripheral State functions. * ****************************************************************************** * @attention * * Copyright (c) 2019 STMicroelectronics. * All rights reserved. * * This software is licensed under terms that can be found in the LICENSE file * in the root directory of this software component. * If no LICENSE file comes with this software, it is provided AS-IS. * ****************************************************************************** @verbatim ============================================================================== ##### How to use this driver ##### ============================================================================== [..] The LPTIM HAL driver can be used as follows: (#)Initialize the LPTIM low level resources by implementing the HAL_LPTIM_MspInit(): (++) Enable the LPTIM interface clock using __HAL_RCC_LPTIMx_CLK_ENABLE(). (++) In case of using interrupts (e.g. HAL_LPTIM_PWM_Start_IT()): (+++) Configure the LPTIM interrupt priority using HAL_NVIC_SetPriority(). (+++) Enable the LPTIM IRQ handler using HAL_NVIC_EnableIRQ(). (+++) In LPTIM IRQ handler, call HAL_LPTIM_IRQHandler(). (#)Initialize the LPTIM HAL using HAL_LPTIM_Init(). This function configures mainly: (++) The instance: LPTIM1. (++) Clock: the counter clock. (+++) Source : it can be either the ULPTIM input (IN1) or one of the internal clock; (APB, LSE or LSI). (+++) Prescaler: select the clock divider. (++) UltraLowPowerClock : To be used only if the ULPTIM is selected as counter clock source. (+++) Polarity: polarity of the active edge for the counter unit if the ULPTIM input is selected. (+++) SampleTime: clock sampling time to configure the clock glitch filter. (++) Trigger: How the counter start. (+++) Source: trigger can be software or one of the hardware triggers. (+++) ActiveEdge : only for hardware trigger. (+++) SampleTime : trigger sampling time to configure the trigger glitch filter. (++) OutputPolarity : 2 opposite polarities are possible. (++) UpdateMode: specifies whether the update of the autoreload and the compare values is done immediately or after the end of current period. (++) Input1Source: Source selected for input1 (GPIO or comparator output). (++) Input2Source: Source selected for input2 (GPIO or comparator output). Input2 is used only for encoder feature so is used only for LPTIM1 instance. (#)Six modes are available: (++) PWM Mode: To generate a PWM signal with specified period and pulse, call HAL_LPTIM_PWM_Start() or HAL_LPTIM_PWM_Start_IT() for interruption mode. (++) One Pulse Mode: To generate pulse with specified width in response to a stimulus, call HAL_LPTIM_OnePulse_Start() or HAL_LPTIM_OnePulse_Start_IT() for interruption mode. (++) Set once Mode: In this mode, the output changes the level (from low level to high level if the output polarity is configured high, else the opposite) when a compare match occurs. To start this mode, call HAL_LPTIM_SetOnce_Start() or HAL_LPTIM_SetOnce_Start_IT() for interruption mode. (++) Encoder Mode: To use the encoder interface call HAL_LPTIM_Encoder_Start() or HAL_LPTIM_Encoder_Start_IT() for interruption mode. Only available for LPTIM1 instance. (++) Time out Mode: an active edge on one selected trigger input rests the counter. The first trigger event will start the timer, any successive trigger event will reset the counter and the timer will restart. To start this mode call HAL_LPTIM_TimeOut_Start_IT() or HAL_LPTIM_TimeOut_Start_IT() for interruption mode. (++) Counter Mode: counter can be used to count external events on the LPTIM Input1 or it can be used to count internal clock cycles. To start this mode, call HAL_LPTIM_Counter_Start() or HAL_LPTIM_Counter_Start_IT() for interruption mode. (#) User can stop any process by calling the corresponding API: HAL_LPTIM_Xxx_Stop() or HAL_LPTIM_Xxx_Stop_IT() if the process is already started in interruption mode. (#) De-initialize the LPTIM peripheral using HAL_LPTIM_DeInit(). *** Callback registration *** ============================================= [..] The compilation define USE_HAL_LPTIM_REGISTER_CALLBACKS when set to 1 allows the user to configure dynamically the driver callbacks. [..] Use Function HAL_LPTIM_RegisterCallback() to register a callback. HAL_LPTIM_RegisterCallback() takes as parameters the HAL peripheral handle, the Callback ID and a pointer to the user callback function. [..] Use function HAL_LPTIM_UnRegisterCallback() to reset a callback to the default weak function. HAL_LPTIM_UnRegisterCallback takes as parameters the HAL peripheral handle, and the Callback ID. [..] These functions allow to register/unregister following callbacks: (+) MspInitCallback : LPTIM Base Msp Init Callback. (+) MspDeInitCallback : LPTIM Base Msp DeInit Callback. (+) CompareMatchCallback : Compare match Callback. (+) AutoReloadMatchCallback : Auto-reload match Callback. (+) TriggerCallback : External trigger event detection Callback. (+) CompareWriteCallback : Compare register write complete Callback. (+) AutoReloadWriteCallback : Auto-reload register write complete Callback. (+) DirectionUpCallback : Up-counting direction change Callback. (+) DirectionDownCallback : Down-counting direction change Callback. [..] By default, after the Init and when the state is HAL_LPTIM_STATE_RESET all interrupt callbacks are set to the corresponding weak functions: examples HAL_LPTIM_TriggerCallback(), HAL_LPTIM_CompareMatchCallback(). [..] Exception done for MspInit and MspDeInit functions that are reset to the legacy weak functionalities in the Init/DeInit only when these callbacks are null (not registered beforehand). If not, MspInit or MspDeInit are not null, the Init/DeInit keep and use the user MspInit/MspDeInit callbacks (registered beforehand) [..] Callbacks can be registered/unregistered in HAL_LPTIM_STATE_READY state only. Exception done MspInit/MspDeInit that can be registered/unregistered in HAL_LPTIM_STATE_READY or HAL_LPTIM_STATE_RESET state, thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit. In that case first register the MspInit/MspDeInit user callbacks using HAL_LPTIM_RegisterCallback() before calling DeInit or Init function. [..] When The compilation define USE_HAL_LPTIM_REGISTER_CALLBACKS is set to 0 or not defined, the callback registration feature is not available and all callbacks are set to the corresponding weak functions. @endverbatim ****************************************************************************** */ /* Includes ------------------------------------------------------------------*/ #include "stm32g4xx_hal.h" /** @addtogroup STM32G4xx_HAL_Driver * @{ */ /** @defgroup LPTIM LPTIM * @brief LPTIM HAL module driver. * @{ */ #ifdef HAL_LPTIM_MODULE_ENABLED /* Private typedef -----------------------------------------------------------*/ /* Private define ------------------------------------------------------------*/ /** @addtogroup LPTIM_Private_Constants * @{ */ #define TIMEOUT 1000UL /* Timeout is 1s */ /** * @} */ /* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /* Private function prototypes -----------------------------------------------*/ #if (USE_HAL_LPTIM_REGISTER_CALLBACKS == 1) static void LPTIM_ResetCallback(LPTIM_HandleTypeDef *lptim); #endif /* USE_HAL_LPTIM_REGISTER_CALLBACKS */ static HAL_StatusTypeDef LPTIM_WaitForFlag(LPTIM_HandleTypeDef *hlptim, uint32_t flag); /* Exported functions --------------------------------------------------------*/ /** @defgroup LPTIM_Exported_Functions LPTIM Exported Functions * @{ */ /** @defgroup LPTIM_Exported_Functions_Group1 Initialization/de-initialization functions * @brief Initialization and Configuration functions. * @verbatim ============================================================================== ##### Initialization and de-initialization functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Initialize the LPTIM according to the specified parameters in the LPTIM_InitTypeDef and initialize the associated handle. (+) DeInitialize the LPTIM peripheral. (+) Initialize the LPTIM MSP. (+) DeInitialize the LPTIM MSP. @endverbatim * @{ */ /** * @brief Initialize the LPTIM according to the specified parameters in the * LPTIM_InitTypeDef and initialize the associated handle. * @param hlptim LPTIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_Init(LPTIM_HandleTypeDef *hlptim) { uint32_t tmpcfgr; /* Check the LPTIM handle allocation */ if (hlptim == NULL) { return HAL_ERROR; } /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); assert_param(IS_LPTIM_CLOCK_SOURCE(hlptim->Init.Clock.Source)); assert_param(IS_LPTIM_CLOCK_PRESCALER(hlptim->Init.Clock.Prescaler)); if ((hlptim->Init.Clock.Source == LPTIM_CLOCKSOURCE_ULPTIM) || (hlptim->Init.CounterSource == LPTIM_COUNTERSOURCE_EXTERNAL)) { assert_param(IS_LPTIM_CLOCK_POLARITY(hlptim->Init.UltraLowPowerClock.Polarity)); assert_param(IS_LPTIM_CLOCK_SAMPLE_TIME(hlptim->Init.UltraLowPowerClock.SampleTime)); } assert_param(IS_LPTIM_TRG_SOURCE(hlptim->Init.Trigger.Source)); if (hlptim->Init.Trigger.Source != LPTIM_TRIGSOURCE_SOFTWARE) { assert_param(IS_LPTIM_EXT_TRG_POLARITY(hlptim->Init.Trigger.ActiveEdge)); assert_param(IS_LPTIM_TRIG_SAMPLE_TIME(hlptim->Init.Trigger.SampleTime)); } assert_param(IS_LPTIM_OUTPUT_POLARITY(hlptim->Init.OutputPolarity)); assert_param(IS_LPTIM_UPDATE_MODE(hlptim->Init.UpdateMode)); assert_param(IS_LPTIM_COUNTER_SOURCE(hlptim->Init.CounterSource)); if (hlptim->State == HAL_LPTIM_STATE_RESET) { /* Allocate lock resource and initialize it */ hlptim->Lock = HAL_UNLOCKED; #if (USE_HAL_LPTIM_REGISTER_CALLBACKS == 1) /* Reset interrupt callbacks to legacy weak callbacks */ LPTIM_ResetCallback(hlptim); if (hlptim->MspInitCallback == NULL) { hlptim->MspInitCallback = HAL_LPTIM_MspInit; } /* Init the low level hardware : GPIO, CLOCK, NVIC */ hlptim->MspInitCallback(hlptim); #else /* Init the low level hardware : GPIO, CLOCK, NVIC */ HAL_LPTIM_MspInit(hlptim); #endif /* USE_HAL_LPTIM_REGISTER_CALLBACKS */ } /* Change the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Get the LPTIMx CFGR value */ tmpcfgr = hlptim->Instance->CFGR; if ((hlptim->Init.Clock.Source == LPTIM_CLOCKSOURCE_ULPTIM) || (hlptim->Init.CounterSource == LPTIM_COUNTERSOURCE_EXTERNAL)) { tmpcfgr &= (uint32_t)(~(LPTIM_CFGR_CKPOL | LPTIM_CFGR_CKFLT)); } if (hlptim->Init.Trigger.Source != LPTIM_TRIGSOURCE_SOFTWARE) { tmpcfgr &= (uint32_t)(~(LPTIM_CFGR_TRGFLT | LPTIM_CFGR_TRIGSEL)); } /* Clear CKSEL, PRESC, TRIGEN, TRGFLT, WAVPOL, PRELOAD & COUNTMODE bits */ tmpcfgr &= (uint32_t)(~(LPTIM_CFGR_CKSEL | LPTIM_CFGR_TRIGEN | LPTIM_CFGR_PRELOAD | LPTIM_CFGR_WAVPOL | LPTIM_CFGR_PRESC | LPTIM_CFGR_COUNTMODE)); /* Set initialization parameters */ tmpcfgr |= (hlptim->Init.Clock.Source | hlptim->Init.Clock.Prescaler | hlptim->Init.OutputPolarity | hlptim->Init.UpdateMode | hlptim->Init.CounterSource); /* Glitch filters for internal triggers and external inputs are configured * only if an internal clock source is provided to the LPTIM */ if (hlptim->Init.Clock.Source == LPTIM_CLOCKSOURCE_APBCLOCK_LPOSC) { tmpcfgr |= (hlptim->Init.Trigger.SampleTime | hlptim->Init.UltraLowPowerClock.SampleTime); } /* Configure LPTIM external clock polarity and digital filter */ if ((hlptim->Init.Clock.Source == LPTIM_CLOCKSOURCE_ULPTIM) || (hlptim->Init.CounterSource == LPTIM_COUNTERSOURCE_EXTERNAL)) { tmpcfgr |= (hlptim->Init.UltraLowPowerClock.Polarity | hlptim->Init.UltraLowPowerClock.SampleTime); } /* Configure LPTIM external trigger */ if (hlptim->Init.Trigger.Source != LPTIM_TRIGSOURCE_SOFTWARE) { /* Enable External trigger and set the trigger source */ tmpcfgr |= (hlptim->Init.Trigger.Source | hlptim->Init.Trigger.ActiveEdge | hlptim->Init.Trigger.SampleTime); } /* Write to LPTIMx CFGR */ hlptim->Instance->CFGR = tmpcfgr; /* Configure LPTIM input sources */ if (hlptim->Instance == LPTIM1) { /* Check LPTIM Input1 and Input2 sources */ assert_param(IS_LPTIM_INPUT1_SOURCE(hlptim->Instance, hlptim->Init.Input1Source)); assert_param(IS_LPTIM_INPUT2_SOURCE(hlptim->Instance, hlptim->Init.Input2Source)); /* Configure LPTIM Input1 and Input2 sources */ hlptim->Instance->OR = (hlptim->Init.Input1Source | hlptim->Init.Input2Source); } /* Change the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief DeInitialize the LPTIM peripheral. * @param hlptim LPTIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_DeInit(LPTIM_HandleTypeDef *hlptim) { /* Check the LPTIM handle allocation */ if (hlptim == NULL) { return HAL_ERROR; } /* Change the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Disable the LPTIM Peripheral Clock */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } #if (USE_HAL_LPTIM_REGISTER_CALLBACKS == 1) if (hlptim->MspDeInitCallback == NULL) { hlptim->MspDeInitCallback = HAL_LPTIM_MspDeInit; } /* DeInit the low level hardware: CLOCK, NVIC.*/ hlptim->MspDeInitCallback(hlptim); #else /* DeInit the low level hardware: CLOCK, NVIC.*/ HAL_LPTIM_MspDeInit(hlptim); #endif /* USE_HAL_LPTIM_REGISTER_CALLBACKS */ /* Change the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_RESET; /* Release Lock */ __HAL_UNLOCK(hlptim); /* Return function status */ return HAL_OK; } /** * @brief Initialize the LPTIM MSP. * @param hlptim LPTIM handle * @retval None */ __weak void HAL_LPTIM_MspInit(LPTIM_HandleTypeDef *hlptim) { /* Prevent unused argument(s) compilation warning */ UNUSED(hlptim); /* NOTE : This function should not be modified, when the callback is needed, the HAL_LPTIM_MspInit could be implemented in the user file */ } /** * @brief DeInitialize LPTIM MSP. * @param hlptim LPTIM handle * @retval None */ __weak void HAL_LPTIM_MspDeInit(LPTIM_HandleTypeDef *hlptim) { /* Prevent unused argument(s) compilation warning */ UNUSED(hlptim); /* NOTE : This function should not be modified, when the callback is needed, the HAL_LPTIM_MspDeInit could be implemented in the user file */ } /** * @} */ /** @defgroup LPTIM_Exported_Functions_Group2 LPTIM Start-Stop operation functions * @brief Start-Stop operation functions. * @verbatim ============================================================================== ##### LPTIM Start Stop operation functions ##### ============================================================================== [..] This section provides functions allowing to: (+) Start the PWM mode. (+) Stop the PWM mode. (+) Start the One pulse mode. (+) Stop the One pulse mode. (+) Start the Set once mode. (+) Stop the Set once mode. (+) Start the Encoder mode. (+) Stop the Encoder mode. (+) Start the Timeout mode. (+) Stop the Timeout mode. (+) Start the Counter mode. (+) Stop the Counter mode. @endverbatim * @{ */ /** * @brief Start the LPTIM PWM generation. * @param hlptim LPTIM handle * @param Period Specifies the Autoreload value. * This parameter must be a value between 0x0000 and 0xFFFF. * @param Pulse Specifies the compare value. * This parameter must be a value between 0x0000 and 0xFFFF. * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_PWM_Start(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Pulse) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); assert_param(IS_LPTIM_PERIOD(Period)); assert_param(IS_LPTIM_PULSE(Pulse)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Reset WAVE bit to set PWM mode */ hlptim->Instance->CFGR &= ~LPTIM_CFGR_WAVE; /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); /* Load the period value in the autoreload register */ __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); /* Wait for the completion of the write operation to the LPTIM_ARR register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_ARROK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_CMPOK); /* Load the pulse value in the compare register */ __HAL_LPTIM_COMPARE_SET(hlptim, Pulse); /* Wait for the completion of the write operation to the LPTIM_CMP register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_CMPOK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Start timer in continuous mode */ __HAL_LPTIM_START_CONTINUOUS(hlptim); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stop the LPTIM PWM generation. * @param hlptim LPTIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_PWM_Stop(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Change the LPTIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Start the LPTIM PWM generation in interrupt mode. * @param hlptim LPTIM handle * @param Period Specifies the Autoreload value. * This parameter must be a value between 0x0000 and 0xFFFF * @param Pulse Specifies the compare value. * This parameter must be a value between 0x0000 and 0xFFFF * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_PWM_Start_IT(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Pulse) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); assert_param(IS_LPTIM_PERIOD(Period)); assert_param(IS_LPTIM_PULSE(Pulse)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Reset WAVE bit to set PWM mode */ hlptim->Instance->CFGR &= ~LPTIM_CFGR_WAVE; /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); /* Load the period value in the autoreload register */ __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); /* Wait for the completion of the write operation to the LPTIM_ARR register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_ARROK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_CMPOK); /* Load the pulse value in the compare register */ __HAL_LPTIM_COMPARE_SET(hlptim, Pulse); /* Wait for the completion of the write operation to the LPTIM_CMP register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_CMPOK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Enable Autoreload write complete interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_ARROK); /* Enable Compare write complete interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_CMPOK); /* Enable Autoreload match interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_ARRM); /* Enable Compare match interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_CMPM); /* If external trigger source is used, then enable external trigger interrupt */ if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) { /* Enable external trigger interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_EXTTRIG); } /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Start timer in continuous mode */ __HAL_LPTIM_START_CONTINUOUS(hlptim); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stop the LPTIM PWM generation in interrupt mode. * @param hlptim LPTIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_PWM_Stop_IT(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Disable Autoreload write complete interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_ARROK); /* Disable Compare write complete interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_CMPOK); /* Disable Autoreload match interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_ARRM); /* Disable Compare match interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_CMPM); /* If external trigger source is used, then disable external trigger interrupt */ if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) { /* Disable external trigger interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_EXTTRIG); } /* Change the LPTIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Start the LPTIM One pulse generation. * @param hlptim LPTIM handle * @param Period Specifies the Autoreload value. * This parameter must be a value between 0x0000 and 0xFFFF. * @param Pulse Specifies the compare value. * This parameter must be a value between 0x0000 and 0xFFFF. * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_OnePulse_Start(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Pulse) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); assert_param(IS_LPTIM_PERIOD(Period)); assert_param(IS_LPTIM_PULSE(Pulse)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Reset WAVE bit to set one pulse mode */ hlptim->Instance->CFGR &= ~LPTIM_CFGR_WAVE; /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); /* Load the period value in the autoreload register */ __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); /* Wait for the completion of the write operation to the LPTIM_ARR register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_ARROK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_CMPOK); /* Load the pulse value in the compare register */ __HAL_LPTIM_COMPARE_SET(hlptim, Pulse); /* Wait for the completion of the write operation to the LPTIM_CMP register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_CMPOK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Start timer in single (one shot) mode */ __HAL_LPTIM_START_SINGLE(hlptim); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stop the LPTIM One pulse generation. * @param hlptim LPTIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_OnePulse_Stop(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Change the LPTIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Start the LPTIM One pulse generation in interrupt mode. * @param hlptim LPTIM handle * @param Period Specifies the Autoreload value. * This parameter must be a value between 0x0000 and 0xFFFF. * @param Pulse Specifies the compare value. * This parameter must be a value between 0x0000 and 0xFFFF. * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_OnePulse_Start_IT(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Pulse) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); assert_param(IS_LPTIM_PERIOD(Period)); assert_param(IS_LPTIM_PULSE(Pulse)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Reset WAVE bit to set one pulse mode */ hlptim->Instance->CFGR &= ~LPTIM_CFGR_WAVE; /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); /* Load the period value in the autoreload register */ __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); /* Wait for the completion of the write operation to the LPTIM_ARR register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_ARROK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_CMPOK); /* Load the pulse value in the compare register */ __HAL_LPTIM_COMPARE_SET(hlptim, Pulse); /* Wait for the completion of the write operation to the LPTIM_CMP register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_CMPOK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Enable Autoreload write complete interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_ARROK); /* Enable Compare write complete interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_CMPOK); /* Enable Autoreload match interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_ARRM); /* Enable Compare match interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_CMPM); /* If external trigger source is used, then enable external trigger interrupt */ if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) { /* Enable external trigger interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_EXTTRIG); } /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Start timer in single (one shot) mode */ __HAL_LPTIM_START_SINGLE(hlptim); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stop the LPTIM One pulse generation in interrupt mode. * @param hlptim LPTIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_OnePulse_Stop_IT(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Disable Autoreload write complete interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_ARROK); /* Disable Compare write complete interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_CMPOK); /* Disable Autoreload match interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_ARRM); /* Disable Compare match interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_CMPM); /* If external trigger source is used, then disable external trigger interrupt */ if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) { /* Disable external trigger interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_EXTTRIG); } /* Change the LPTIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Start the LPTIM in Set once mode. * @param hlptim LPTIM handle * @param Period Specifies the Autoreload value. * This parameter must be a value between 0x0000 and 0xFFFF. * @param Pulse Specifies the compare value. * This parameter must be a value between 0x0000 and 0xFFFF. * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_SetOnce_Start(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Pulse) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); assert_param(IS_LPTIM_PERIOD(Period)); assert_param(IS_LPTIM_PULSE(Pulse)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Set WAVE bit to enable the set once mode */ hlptim->Instance->CFGR |= LPTIM_CFGR_WAVE; /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); /* Load the period value in the autoreload register */ __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); /* Wait for the completion of the write operation to the LPTIM_ARR register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_ARROK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_CMPOK); /* Load the pulse value in the compare register */ __HAL_LPTIM_COMPARE_SET(hlptim, Pulse); /* Wait for the completion of the write operation to the LPTIM_CMP register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_CMPOK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Start timer in single (one shot) mode */ __HAL_LPTIM_START_SINGLE(hlptim); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stop the LPTIM Set once mode. * @param hlptim LPTIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_SetOnce_Stop(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Change the LPTIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Start the LPTIM Set once mode in interrupt mode. * @param hlptim LPTIM handle * @param Period Specifies the Autoreload value. * This parameter must be a value between 0x0000 and 0xFFFF. * @param Pulse Specifies the compare value. * This parameter must be a value between 0x0000 and 0xFFFF. * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_SetOnce_Start_IT(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Pulse) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); assert_param(IS_LPTIM_PERIOD(Period)); assert_param(IS_LPTIM_PULSE(Pulse)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Set WAVE bit to enable the set once mode */ hlptim->Instance->CFGR |= LPTIM_CFGR_WAVE; /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); /* Load the period value in the autoreload register */ __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); /* Wait for the completion of the write operation to the LPTIM_ARR register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_ARROK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_CMPOK); /* Load the pulse value in the compare register */ __HAL_LPTIM_COMPARE_SET(hlptim, Pulse); /* Wait for the completion of the write operation to the LPTIM_CMP register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_CMPOK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Enable Autoreload write complete interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_ARROK); /* Enable Compare write complete interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_CMPOK); /* Enable Autoreload match interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_ARRM); /* Enable Compare match interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_CMPM); /* If external trigger source is used, then enable external trigger interrupt */ if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) { /* Enable external trigger interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_EXTTRIG); } /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Start timer in single (one shot) mode */ __HAL_LPTIM_START_SINGLE(hlptim); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stop the LPTIM Set once mode in interrupt mode. * @param hlptim LPTIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_SetOnce_Stop_IT(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Disable Autoreload write complete interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_ARROK); /* Disable Compare write complete interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_CMPOK); /* Disable Autoreload match interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_ARRM); /* Disable Compare match interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_CMPM); /* If external trigger source is used, then disable external trigger interrupt */ if ((hlptim->Init.Trigger.Source) != LPTIM_TRIGSOURCE_SOFTWARE) { /* Disable external trigger interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_EXTTRIG); } /* Change the LPTIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Start the Encoder interface. * @param hlptim LPTIM handle * @param Period Specifies the Autoreload value. * This parameter must be a value between 0x0000 and 0xFFFF. * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_Encoder_Start(LPTIM_HandleTypeDef *hlptim, uint32_t Period) { uint32_t tmpcfgr; /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); assert_param(IS_LPTIM_PERIOD(Period)); assert_param(hlptim->Init.Clock.Source == LPTIM_CLOCKSOURCE_APBCLOCK_LPOSC); assert_param(hlptim->Init.Clock.Prescaler == LPTIM_PRESCALER_DIV1); assert_param(IS_LPTIM_CLOCK_POLARITY(hlptim->Init.UltraLowPowerClock.Polarity)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Get the LPTIMx CFGR value */ tmpcfgr = hlptim->Instance->CFGR; /* Clear CKPOL bits */ tmpcfgr &= (uint32_t)(~LPTIM_CFGR_CKPOL); /* Set Input polarity */ tmpcfgr |= hlptim->Init.UltraLowPowerClock.Polarity; /* Write to LPTIMx CFGR */ hlptim->Instance->CFGR = tmpcfgr; /* Set ENC bit to enable the encoder interface */ hlptim->Instance->CFGR |= LPTIM_CFGR_ENC; /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); /* Load the period value in the autoreload register */ __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); /* Wait for the completion of the write operation to the LPTIM_ARR register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_ARROK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Start timer in continuous mode */ __HAL_LPTIM_START_CONTINUOUS(hlptim); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stop the Encoder interface. * @param hlptim LPTIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_Encoder_Stop(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Reset ENC bit to disable the encoder interface */ hlptim->Instance->CFGR &= ~LPTIM_CFGR_ENC; /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Start the Encoder interface in interrupt mode. * @param hlptim LPTIM handle * @param Period Specifies the Autoreload value. * This parameter must be a value between 0x0000 and 0xFFFF. * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_Encoder_Start_IT(LPTIM_HandleTypeDef *hlptim, uint32_t Period) { uint32_t tmpcfgr; /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); assert_param(IS_LPTIM_PERIOD(Period)); assert_param(hlptim->Init.Clock.Source == LPTIM_CLOCKSOURCE_APBCLOCK_LPOSC); assert_param(hlptim->Init.Clock.Prescaler == LPTIM_PRESCALER_DIV1); assert_param(IS_LPTIM_CLOCK_POLARITY(hlptim->Init.UltraLowPowerClock.Polarity)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Configure edge sensitivity for encoder mode */ /* Get the LPTIMx CFGR value */ tmpcfgr = hlptim->Instance->CFGR; /* Clear CKPOL bits */ tmpcfgr &= (uint32_t)(~LPTIM_CFGR_CKPOL); /* Set Input polarity */ tmpcfgr |= hlptim->Init.UltraLowPowerClock.Polarity; /* Write to LPTIMx CFGR */ hlptim->Instance->CFGR = tmpcfgr; /* Set ENC bit to enable the encoder interface */ hlptim->Instance->CFGR |= LPTIM_CFGR_ENC; /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); /* Load the period value in the autoreload register */ __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); /* Wait for the completion of the write operation to the LPTIM_ARR register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_ARROK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Enable "switch to down direction" interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_DOWN); /* Enable "switch to up direction" interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_UP); /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Start timer in continuous mode */ __HAL_LPTIM_START_CONTINUOUS(hlptim); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stop the Encoder interface in interrupt mode. * @param hlptim LPTIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_Encoder_Stop_IT(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Reset ENC bit to disable the encoder interface */ hlptim->Instance->CFGR &= ~LPTIM_CFGR_ENC; /* Disable "switch to down direction" interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_DOWN); /* Disable "switch to up direction" interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_UP); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Start the Timeout function. * @note The first trigger event will start the timer, any successive * trigger event will reset the counter and the timer restarts. * @param hlptim LPTIM handle * @param Period Specifies the Autoreload value. * This parameter must be a value between 0x0000 and 0xFFFF. * @param Timeout Specifies the TimeOut value to reset the counter. * This parameter must be a value between 0x0000 and 0xFFFF. * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_TimeOut_Start(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Timeout) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); assert_param(IS_LPTIM_PERIOD(Period)); assert_param(IS_LPTIM_PULSE(Timeout)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Set TIMOUT bit to enable the timeout function */ hlptim->Instance->CFGR |= LPTIM_CFGR_TIMOUT; /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); /* Load the period value in the autoreload register */ __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); /* Wait for the completion of the write operation to the LPTIM_ARR register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_ARROK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_CMPOK); /* Load the Timeout value in the compare register */ __HAL_LPTIM_COMPARE_SET(hlptim, Timeout); /* Wait for the completion of the write operation to the LPTIM_CMP register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_CMPOK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Start timer in continuous mode */ __HAL_LPTIM_START_CONTINUOUS(hlptim); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stop the Timeout function. * @param hlptim LPTIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_TimeOut_Stop(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Reset TIMOUT bit to enable the timeout function */ hlptim->Instance->CFGR &= ~LPTIM_CFGR_TIMOUT; /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Start the Timeout function in interrupt mode. * @note The first trigger event will start the timer, any successive * trigger event will reset the counter and the timer restarts. * @param hlptim LPTIM handle * @param Period Specifies the Autoreload value. * This parameter must be a value between 0x0000 and 0xFFFF. * @param Timeout Specifies the TimeOut value to reset the counter. * This parameter must be a value between 0x0000 and 0xFFFF. * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_TimeOut_Start_IT(LPTIM_HandleTypeDef *hlptim, uint32_t Period, uint32_t Timeout) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); assert_param(IS_LPTIM_PERIOD(Period)); assert_param(IS_LPTIM_PULSE(Timeout)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Enable EXTI Line interrupt on the LPTIM Wake-up Timer */ __HAL_LPTIM_WAKEUPTIMER_EXTI_ENABLE_IT(); /* Set TIMOUT bit to enable the timeout function */ hlptim->Instance->CFGR |= LPTIM_CFGR_TIMOUT; /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); /* Load the period value in the autoreload register */ __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); /* Wait for the completion of the write operation to the LPTIM_ARR register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_ARROK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_CMPOK); /* Load the Timeout value in the compare register */ __HAL_LPTIM_COMPARE_SET(hlptim, Timeout); /* Wait for the completion of the write operation to the LPTIM_CMP register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_CMPOK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Enable Compare match interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_CMPM); /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Start timer in continuous mode */ __HAL_LPTIM_START_CONTINUOUS(hlptim); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stop the Timeout function in interrupt mode. * @param hlptim LPTIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_TimeOut_Stop_IT(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Disable EXTI Line interrupt on the LPTIM Wake-up Timer */ __HAL_LPTIM_WAKEUPTIMER_EXTI_DISABLE_IT(); /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Reset TIMOUT bit to enable the timeout function */ hlptim->Instance->CFGR &= ~LPTIM_CFGR_TIMOUT; /* Disable Compare match interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_CMPM); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Start the Counter mode. * @param hlptim LPTIM handle * @param Period Specifies the Autoreload value. * This parameter must be a value between 0x0000 and 0xFFFF. * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_Counter_Start(LPTIM_HandleTypeDef *hlptim, uint32_t Period) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); assert_param(IS_LPTIM_PERIOD(Period)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* If clock source is not ULPTIM clock and counter source is external, then it must not be prescaled */ if ((hlptim->Init.Clock.Source != LPTIM_CLOCKSOURCE_ULPTIM) && (hlptim->Init.CounterSource == LPTIM_COUNTERSOURCE_EXTERNAL)) { /* Check if clock is prescaled */ assert_param(IS_LPTIM_CLOCK_PRESCALERDIV1(hlptim->Init.Clock.Prescaler)); /* Set clock prescaler to 0 */ hlptim->Instance->CFGR &= ~LPTIM_CFGR_PRESC; } /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); /* Load the period value in the autoreload register */ __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); /* Wait for the completion of the write operation to the LPTIM_ARR register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_ARROK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Start timer in continuous mode */ __HAL_LPTIM_START_CONTINUOUS(hlptim); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stop the Counter mode. * @param hlptim LPTIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_Counter_Stop(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Start the Counter mode in interrupt mode. * @param hlptim LPTIM handle * @param Period Specifies the Autoreload value. * This parameter must be a value between 0x0000 and 0xFFFF. * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_Counter_Start_IT(LPTIM_HandleTypeDef *hlptim, uint32_t Period) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); assert_param(IS_LPTIM_PERIOD(Period)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Enable EXTI Line interrupt on the LPTIM Wake-up Timer */ __HAL_LPTIM_WAKEUPTIMER_EXTI_ENABLE_IT(); /* If clock source is not ULPTIM clock and counter source is external, then it must not be prescaled */ if ((hlptim->Init.Clock.Source != LPTIM_CLOCKSOURCE_ULPTIM) && (hlptim->Init.CounterSource == LPTIM_COUNTERSOURCE_EXTERNAL)) { /* Check if clock is prescaled */ assert_param(IS_LPTIM_CLOCK_PRESCALERDIV1(hlptim->Init.Clock.Prescaler)); /* Set clock prescaler to 0 */ hlptim->Instance->CFGR &= ~LPTIM_CFGR_PRESC; } /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Clear flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); /* Load the period value in the autoreload register */ __HAL_LPTIM_AUTORELOAD_SET(hlptim, Period); /* Wait for the completion of the write operation to the LPTIM_ARR register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_ARROK) == HAL_TIMEOUT) { return HAL_TIMEOUT; } /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Enable Autoreload write complete interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_ARROK); /* Enable Autoreload match interrupt */ __HAL_LPTIM_ENABLE_IT(hlptim, LPTIM_IT_ARRM); /* Enable the Peripheral */ __HAL_LPTIM_ENABLE(hlptim); /* Start timer in continuous mode */ __HAL_LPTIM_START_CONTINUOUS(hlptim); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @brief Stop the Counter mode in interrupt mode. * @param hlptim LPTIM handle * @retval HAL status */ HAL_StatusTypeDef HAL_LPTIM_Counter_Stop_IT(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); /* Set the LPTIM state */ hlptim->State = HAL_LPTIM_STATE_BUSY; /* Disable EXTI Line interrupt on the LPTIM Wake-up Timer */ __HAL_LPTIM_WAKEUPTIMER_EXTI_DISABLE_IT(); /* Disable the Peripheral */ __HAL_LPTIM_DISABLE(hlptim); if (HAL_LPTIM_GetState(hlptim) == HAL_LPTIM_STATE_TIMEOUT) { return HAL_TIMEOUT; } /* Disable Autoreload write complete interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_ARROK); /* Disable Autoreload match interrupt */ __HAL_LPTIM_DISABLE_IT(hlptim, LPTIM_IT_ARRM); /* Change the TIM state*/ hlptim->State = HAL_LPTIM_STATE_READY; /* Return function status */ return HAL_OK; } /** * @} */ /** @defgroup LPTIM_Exported_Functions_Group3 LPTIM Read operation functions * @brief Read operation functions. * @verbatim ============================================================================== ##### LPTIM Read operation functions ##### ============================================================================== [..] This section provides LPTIM Reading functions. (+) Read the counter value. (+) Read the period (Auto-reload) value. (+) Read the pulse (Compare)value. @endverbatim * @{ */ /** * @brief Return the current counter value. * @param hlptim LPTIM handle * @retval Counter value. */ uint32_t HAL_LPTIM_ReadCounter(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); return (hlptim->Instance->CNT); } /** * @brief Return the current Autoreload (Period) value. * @param hlptim LPTIM handle * @retval Autoreload value. */ uint32_t HAL_LPTIM_ReadAutoReload(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); return (hlptim->Instance->ARR); } /** * @brief Return the current Compare (Pulse) value. * @param hlptim LPTIM handle * @retval Compare value. */ uint32_t HAL_LPTIM_ReadCompare(LPTIM_HandleTypeDef *hlptim) { /* Check the parameters */ assert_param(IS_LPTIM_INSTANCE(hlptim->Instance)); return (hlptim->Instance->CMP); } /** * @} */ /** @defgroup LPTIM_Exported_Functions_Group4 LPTIM IRQ handler and callbacks * @brief LPTIM IRQ handler. * @verbatim ============================================================================== ##### LPTIM IRQ handler and callbacks ##### ============================================================================== [..] This section provides LPTIM IRQ handler and callback functions called within the IRQ handler: (+) LPTIM interrupt request handler (+) Compare match Callback (+) Auto-reload match Callback (+) External trigger event detection Callback (+) Compare register write complete Callback (+) Auto-reload register write complete Callback (+) Up-counting direction change Callback (+) Down-counting direction change Callback @endverbatim * @{ */ /** * @brief Handle LPTIM interrupt request. * @param hlptim LPTIM handle * @retval None */ void HAL_LPTIM_IRQHandler(LPTIM_HandleTypeDef *hlptim) { /* Compare match interrupt */ if (__HAL_LPTIM_GET_FLAG(hlptim, LPTIM_FLAG_CMPM) != RESET) { if (__HAL_LPTIM_GET_IT_SOURCE(hlptim, LPTIM_IT_CMPM) != RESET) { /* Clear Compare match flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_CMPM); /* Compare match Callback */ #if (USE_HAL_LPTIM_REGISTER_CALLBACKS == 1) hlptim->CompareMatchCallback(hlptim); #else HAL_LPTIM_CompareMatchCallback(hlptim); #endif /* USE_HAL_LPTIM_REGISTER_CALLBACKS */ } } /* Autoreload match interrupt */ if (__HAL_LPTIM_GET_FLAG(hlptim, LPTIM_FLAG_ARRM) != RESET) { if (__HAL_LPTIM_GET_IT_SOURCE(hlptim, LPTIM_IT_ARRM) != RESET) { /* Clear Autoreload match flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARRM); /* Autoreload match Callback */ #if (USE_HAL_LPTIM_REGISTER_CALLBACKS == 1) hlptim->AutoReloadMatchCallback(hlptim); #else HAL_LPTIM_AutoReloadMatchCallback(hlptim); #endif /* USE_HAL_LPTIM_REGISTER_CALLBACKS */ } } /* Trigger detected interrupt */ if (__HAL_LPTIM_GET_FLAG(hlptim, LPTIM_FLAG_EXTTRIG) != RESET) { if (__HAL_LPTIM_GET_IT_SOURCE(hlptim, LPTIM_IT_EXTTRIG) != RESET) { /* Clear Trigger detected flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_EXTTRIG); /* Trigger detected callback */ #if (USE_HAL_LPTIM_REGISTER_CALLBACKS == 1) hlptim->TriggerCallback(hlptim); #else HAL_LPTIM_TriggerCallback(hlptim); #endif /* USE_HAL_LPTIM_REGISTER_CALLBACKS */ } } /* Compare write interrupt */ if (__HAL_LPTIM_GET_FLAG(hlptim, LPTIM_FLAG_CMPOK) != RESET) { if (__HAL_LPTIM_GET_IT_SOURCE(hlptim, LPTIM_IT_CMPOK) != RESET) { /* Clear Compare write flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_CMPOK); /* Compare write Callback */ #if (USE_HAL_LPTIM_REGISTER_CALLBACKS == 1) hlptim->CompareWriteCallback(hlptim); #else HAL_LPTIM_CompareWriteCallback(hlptim); #endif /* USE_HAL_LPTIM_REGISTER_CALLBACKS */ } } /* Autoreload write interrupt */ if (__HAL_LPTIM_GET_FLAG(hlptim, LPTIM_FLAG_ARROK) != RESET) { if (__HAL_LPTIM_GET_IT_SOURCE(hlptim, LPTIM_IT_ARROK) != RESET) { /* Clear Autoreload write flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); /* Autoreload write Callback */ #if (USE_HAL_LPTIM_REGISTER_CALLBACKS == 1) hlptim->AutoReloadWriteCallback(hlptim); #else HAL_LPTIM_AutoReloadWriteCallback(hlptim); #endif /* USE_HAL_LPTIM_REGISTER_CALLBACKS */ } } /* Direction counter changed from Down to Up interrupt */ if (__HAL_LPTIM_GET_FLAG(hlptim, LPTIM_FLAG_UP) != RESET) { if (__HAL_LPTIM_GET_IT_SOURCE(hlptim, LPTIM_IT_UP) != RESET) { /* Clear Direction counter changed from Down to Up flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_UP); /* Direction counter changed from Down to Up Callback */ #if (USE_HAL_LPTIM_REGISTER_CALLBACKS == 1) hlptim->DirectionUpCallback(hlptim); #else HAL_LPTIM_DirectionUpCallback(hlptim); #endif /* USE_HAL_LPTIM_REGISTER_CALLBACKS */ } } /* Direction counter changed from Up to Down interrupt */ if (__HAL_LPTIM_GET_FLAG(hlptim, LPTIM_FLAG_DOWN) != RESET) { if (__HAL_LPTIM_GET_IT_SOURCE(hlptim, LPTIM_IT_DOWN) != RESET) { /* Clear Direction counter changed from Up to Down flag */ __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_DOWN); /* Direction counter changed from Up to Down Callback */ #if (USE_HAL_LPTIM_REGISTER_CALLBACKS == 1) hlptim->DirectionDownCallback(hlptim); #else HAL_LPTIM_DirectionDownCallback(hlptim); #endif /* USE_HAL_LPTIM_REGISTER_CALLBACKS */ } } } /** * @brief Compare match callback in non-blocking mode. * @param hlptim LPTIM handle * @retval None */ __weak void HAL_LPTIM_CompareMatchCallback(LPTIM_HandleTypeDef *hlptim) { /* Prevent unused argument(s) compilation warning */ UNUSED(hlptim); /* NOTE : This function should not be modified, when the callback is needed, the HAL_LPTIM_CompareMatchCallback could be implemented in the user file */ } /** * @brief Autoreload match callback in non-blocking mode. * @param hlptim LPTIM handle * @retval None */ __weak void HAL_LPTIM_AutoReloadMatchCallback(LPTIM_HandleTypeDef *hlptim) { /* Prevent unused argument(s) compilation warning */ UNUSED(hlptim); /* NOTE : This function should not be modified, when the callback is needed, the HAL_LPTIM_AutoReloadMatchCallback could be implemented in the user file */ } /** * @brief Trigger detected callback in non-blocking mode. * @param hlptim LPTIM handle * @retval None */ __weak void HAL_LPTIM_TriggerCallback(LPTIM_HandleTypeDef *hlptim) { /* Prevent unused argument(s) compilation warning */ UNUSED(hlptim); /* NOTE : This function should not be modified, when the callback is needed, the HAL_LPTIM_TriggerCallback could be implemented in the user file */ } /** * @brief Compare write callback in non-blocking mode. * @param hlptim LPTIM handle * @retval None */ __weak void HAL_LPTIM_CompareWriteCallback(LPTIM_HandleTypeDef *hlptim) { /* Prevent unused argument(s) compilation warning */ UNUSED(hlptim); /* NOTE : This function should not be modified, when the callback is needed, the HAL_LPTIM_CompareWriteCallback could be implemented in the user file */ } /** * @brief Autoreload write callback in non-blocking mode. * @param hlptim LPTIM handle * @retval None */ __weak void HAL_LPTIM_AutoReloadWriteCallback(LPTIM_HandleTypeDef *hlptim) { /* Prevent unused argument(s) compilation warning */ UNUSED(hlptim); /* NOTE : This function should not be modified, when the callback is needed, the HAL_LPTIM_AutoReloadWriteCallback could be implemented in the user file */ } /** * @brief Direction counter changed from Down to Up callback in non-blocking mode. * @param hlptim LPTIM handle * @retval None */ __weak void HAL_LPTIM_DirectionUpCallback(LPTIM_HandleTypeDef *hlptim) { /* Prevent unused argument(s) compilation warning */ UNUSED(hlptim); /* NOTE : This function should not be modified, when the callback is needed, the HAL_LPTIM_DirectionUpCallback could be implemented in the user file */ } /** * @brief Direction counter changed from Up to Down callback in non-blocking mode. * @param hlptim LPTIM handle * @retval None */ __weak void HAL_LPTIM_DirectionDownCallback(LPTIM_HandleTypeDef *hlptim) { /* Prevent unused argument(s) compilation warning */ UNUSED(hlptim); /* NOTE : This function should not be modified, when the callback is needed, the HAL_LPTIM_DirectionDownCallback could be implemented in the user file */ } #if (USE_HAL_LPTIM_REGISTER_CALLBACKS == 1) /** * @brief Register a User LPTIM callback to be used instead of the weak predefined callback * @param hlptim LPTIM handle * @param CallbackID ID of the callback to be registered * This parameter can be one of the following values: * @arg @ref HAL_LPTIM_MSPINIT_CB_ID LPTIM Base Msp Init Callback ID * @arg @ref HAL_LPTIM_MSPDEINIT_CB_ID LPTIM Base Msp DeInit Callback ID * @arg @ref HAL_LPTIM_COMPARE_MATCH_CB_ID Compare match Callback ID * @arg @ref HAL_LPTIM_AUTORELOAD_MATCH_CB_ID Auto-reload match Callback ID * @arg @ref HAL_LPTIM_TRIGGER_CB_ID External trigger event detection Callback ID * @arg @ref HAL_LPTIM_COMPARE_WRITE_CB_ID Compare register write complete Callback ID * @arg @ref HAL_LPTIM_AUTORELOAD_WRITE_CB_ID Auto-reload register write complete Callback ID * @arg @ref HAL_LPTIM_DIRECTION_UP_CB_ID Up-counting direction change Callback ID * @arg @ref HAL_LPTIM_DIRECTION_DOWN_CB_ID Down-counting direction change Callback ID * @param pCallback pointer to the callback function * @retval status */ HAL_StatusTypeDef HAL_LPTIM_RegisterCallback(LPTIM_HandleTypeDef *hlptim, HAL_LPTIM_CallbackIDTypeDef CallbackID, pLPTIM_CallbackTypeDef pCallback) { HAL_StatusTypeDef status = HAL_OK; if (pCallback == NULL) { return HAL_ERROR; } /* Process locked */ __HAL_LOCK(hlptim); if (hlptim->State == HAL_LPTIM_STATE_READY) { switch (CallbackID) { case HAL_LPTIM_MSPINIT_CB_ID : hlptim->MspInitCallback = pCallback; break; case HAL_LPTIM_MSPDEINIT_CB_ID : hlptim->MspDeInitCallback = pCallback; break; case HAL_LPTIM_COMPARE_MATCH_CB_ID : hlptim->CompareMatchCallback = pCallback; break; case HAL_LPTIM_AUTORELOAD_MATCH_CB_ID : hlptim->AutoReloadMatchCallback = pCallback; break; case HAL_LPTIM_TRIGGER_CB_ID : hlptim->TriggerCallback = pCallback; break; case HAL_LPTIM_COMPARE_WRITE_CB_ID : hlptim->CompareWriteCallback = pCallback; break; case HAL_LPTIM_AUTORELOAD_WRITE_CB_ID : hlptim->AutoReloadWriteCallback = pCallback; break; case HAL_LPTIM_DIRECTION_UP_CB_ID : hlptim->DirectionUpCallback = pCallback; break; case HAL_LPTIM_DIRECTION_DOWN_CB_ID : hlptim->DirectionDownCallback = pCallback; break; default : /* Return error status */ status = HAL_ERROR; break; } } else if (hlptim->State == HAL_LPTIM_STATE_RESET) { switch (CallbackID) { case HAL_LPTIM_MSPINIT_CB_ID : hlptim->MspInitCallback = pCallback; break; case HAL_LPTIM_MSPDEINIT_CB_ID : hlptim->MspDeInitCallback = pCallback; break; default : /* Return error status */ status = HAL_ERROR; break; } } else { /* Return error status */ status = HAL_ERROR; } /* Release Lock */ __HAL_UNLOCK(hlptim); return status; } /** * @brief Unregister a LPTIM callback * LLPTIM callback is redirected to the weak predefined callback * @param hlptim LPTIM handle * @param CallbackID ID of the callback to be unregistered * This parameter can be one of the following values: * @arg @ref HAL_LPTIM_MSPINIT_CB_ID LPTIM Base Msp Init Callback ID * @arg @ref HAL_LPTIM_MSPDEINIT_CB_ID LPTIM Base Msp DeInit Callback ID * @arg @ref HAL_LPTIM_COMPARE_MATCH_CB_ID Compare match Callback ID * @arg @ref HAL_LPTIM_AUTORELOAD_MATCH_CB_ID Auto-reload match Callback ID * @arg @ref HAL_LPTIM_TRIGGER_CB_ID External trigger event detection Callback ID * @arg @ref HAL_LPTIM_COMPARE_WRITE_CB_ID Compare register write complete Callback ID * @arg @ref HAL_LPTIM_AUTORELOAD_WRITE_CB_ID Auto-reload register write complete Callback ID * @arg @ref HAL_LPTIM_DIRECTION_UP_CB_ID Up-counting direction change Callback ID * @arg @ref HAL_LPTIM_DIRECTION_DOWN_CB_ID Down-counting direction change Callback ID * @retval status */ HAL_StatusTypeDef HAL_LPTIM_UnRegisterCallback(LPTIM_HandleTypeDef *hlptim, HAL_LPTIM_CallbackIDTypeDef CallbackID) { HAL_StatusTypeDef status = HAL_OK; /* Process locked */ __HAL_LOCK(hlptim); if (hlptim->State == HAL_LPTIM_STATE_READY) { switch (CallbackID) { case HAL_LPTIM_MSPINIT_CB_ID : /* Legacy weak MspInit Callback */ hlptim->MspInitCallback = HAL_LPTIM_MspInit; break; case HAL_LPTIM_MSPDEINIT_CB_ID : /* Legacy weak Msp DeInit Callback */ hlptim->MspDeInitCallback = HAL_LPTIM_MspDeInit; break; case HAL_LPTIM_COMPARE_MATCH_CB_ID : /* Legacy weak Compare match Callback */ hlptim->CompareMatchCallback = HAL_LPTIM_CompareMatchCallback; break; case HAL_LPTIM_AUTORELOAD_MATCH_CB_ID : /* Legacy weak Auto-reload match Callback */ hlptim->AutoReloadMatchCallback = HAL_LPTIM_AutoReloadMatchCallback; break; case HAL_LPTIM_TRIGGER_CB_ID : /* Legacy weak External trigger event detection Callback */ hlptim->TriggerCallback = HAL_LPTIM_TriggerCallback; break; case HAL_LPTIM_COMPARE_WRITE_CB_ID : /* Legacy weak Compare register write complete Callback */ hlptim->CompareWriteCallback = HAL_LPTIM_CompareWriteCallback; break; case HAL_LPTIM_AUTORELOAD_WRITE_CB_ID : /* Legacy weak Auto-reload register write complete Callback */ hlptim->AutoReloadWriteCallback = HAL_LPTIM_AutoReloadWriteCallback; break; case HAL_LPTIM_DIRECTION_UP_CB_ID : /* Legacy weak Up-counting direction change Callback */ hlptim->DirectionUpCallback = HAL_LPTIM_DirectionUpCallback; break; case HAL_LPTIM_DIRECTION_DOWN_CB_ID : /* Legacy weak Down-counting direction change Callback */ hlptim->DirectionDownCallback = HAL_LPTIM_DirectionDownCallback; break; default : /* Return error status */ status = HAL_ERROR; break; } } else if (hlptim->State == HAL_LPTIM_STATE_RESET) { switch (CallbackID) { case HAL_LPTIM_MSPINIT_CB_ID : /* Legacy weak MspInit Callback */ hlptim->MspInitCallback = HAL_LPTIM_MspInit; break; case HAL_LPTIM_MSPDEINIT_CB_ID : /* Legacy weak Msp DeInit Callback */ hlptim->MspDeInitCallback = HAL_LPTIM_MspDeInit; break; default : /* Return error status */ status = HAL_ERROR; break; } } else { /* Return error status */ status = HAL_ERROR; } /* Release Lock */ __HAL_UNLOCK(hlptim); return status; } #endif /* USE_HAL_LPTIM_REGISTER_CALLBACKS */ /** * @} */ /** @defgroup LPTIM_Group5 Peripheral State functions * @brief Peripheral State functions. * @verbatim ============================================================================== ##### Peripheral State functions ##### ============================================================================== [..] This subsection permits to get in run-time the status of the peripheral. @endverbatim * @{ */ /** * @brief Return the LPTIM handle state. * @param hlptim LPTIM handle * @retval HAL state */ HAL_LPTIM_StateTypeDef HAL_LPTIM_GetState(LPTIM_HandleTypeDef *hlptim) { /* Return LPTIM handle state */ return hlptim->State; } /** * @} */ /** * @} */ /* Private functions ---------------------------------------------------------*/ /** @defgroup LPTIM_Private_Functions LPTIM Private Functions * @{ */ #if (USE_HAL_LPTIM_REGISTER_CALLBACKS == 1) /** * @brief Reset interrupt callbacks to the legacy weak callbacks. * @param lptim pointer to a LPTIM_HandleTypeDef structure that contains * the configuration information for LPTIM module. * @retval None */ static void LPTIM_ResetCallback(LPTIM_HandleTypeDef *lptim) { /* Reset the LPTIM callback to the legacy weak callbacks */ lptim->CompareMatchCallback = HAL_LPTIM_CompareMatchCallback; lptim->AutoReloadMatchCallback = HAL_LPTIM_AutoReloadMatchCallback; lptim->TriggerCallback = HAL_LPTIM_TriggerCallback; lptim->CompareWriteCallback = HAL_LPTIM_CompareWriteCallback; lptim->AutoReloadWriteCallback = HAL_LPTIM_AutoReloadWriteCallback; lptim->DirectionUpCallback = HAL_LPTIM_DirectionUpCallback; lptim->DirectionDownCallback = HAL_LPTIM_DirectionDownCallback; } #endif /* USE_HAL_LPTIM_REGISTER_CALLBACKS */ /** * @brief LPTimer Wait for flag set * @param hlptim pointer to a LPTIM_HandleTypeDef structure that contains * the configuration information for LPTIM module. * @param flag The lptim flag * @retval HAL status */ static HAL_StatusTypeDef LPTIM_WaitForFlag(LPTIM_HandleTypeDef *hlptim, uint32_t flag) { HAL_StatusTypeDef result = HAL_OK; uint32_t count = TIMEOUT * (SystemCoreClock / 20UL / 1000UL); do { count--; if (count == 0UL) { result = HAL_TIMEOUT; } } while ((!(__HAL_LPTIM_GET_FLAG((hlptim), (flag)))) && (count != 0UL)); return result; } /** * @brief Disable LPTIM HW instance. * @param hlptim pointer to a LPTIM_HandleTypeDef structure that contains * the configuration information for LPTIM module. * @note The following sequence is required to solve LPTIM disable HW limitation. * Please check Errata Sheet ES0335 for more details under "MCU may remain * stuck in LPTIM interrupt when entering Stop mode" section. * @retval None */ void LPTIM_Disable(LPTIM_HandleTypeDef *hlptim) { uint32_t tmpclksource = 0; uint32_t tmpIER; uint32_t tmpCFGR; uint32_t tmpCMP; uint32_t tmpARR; uint32_t primask_bit; uint32_t tmpOR; /* Enter critical section */ primask_bit = __get_PRIMASK(); __set_PRIMASK(1) ; /*********** Save LPTIM Config ***********/ /* Save LPTIM source clock */ switch ((uint32_t)hlptim->Instance) { case LPTIM1_BASE: tmpclksource = __HAL_RCC_GET_LPTIM1_SOURCE(); break; default: break; } /* Save LPTIM configuration registers */ tmpIER = hlptim->Instance->IER; tmpCFGR = hlptim->Instance->CFGR; tmpCMP = hlptim->Instance->CMP; tmpARR = hlptim->Instance->ARR; tmpOR = hlptim->Instance->OR; /*********** Reset LPTIM ***********/ switch ((uint32_t)hlptim->Instance) { case LPTIM1_BASE: __HAL_RCC_LPTIM1_FORCE_RESET(); __HAL_RCC_LPTIM1_RELEASE_RESET(); break; default: break; } /*********** Restore LPTIM Config ***********/ if ((tmpCMP != 0UL) || (tmpARR != 0UL)) { /* Force LPTIM source kernel clock from APB */ switch ((uint32_t)hlptim->Instance) { case LPTIM1_BASE: __HAL_RCC_LPTIM1_CONFIG(RCC_LPTIM1CLKSOURCE_PCLK1); break; default: break; } if (tmpCMP != 0UL) { /* Restore CMP register (LPTIM should be enabled first) */ hlptim->Instance->CR |= LPTIM_CR_ENABLE; hlptim->Instance->CMP = tmpCMP; /* Wait for the completion of the write operation to the LPTIM_CMP register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_CMPOK) == HAL_TIMEOUT) { hlptim->State = HAL_LPTIM_STATE_TIMEOUT; } __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_CMPOK); } if (tmpARR != 0UL) { /* Restore ARR register (LPTIM should be enabled first) */ hlptim->Instance->CR |= LPTIM_CR_ENABLE; hlptim->Instance->ARR = tmpARR; /* Wait for the completion of the write operation to the LPTIM_ARR register */ if (LPTIM_WaitForFlag(hlptim, LPTIM_FLAG_ARROK) == HAL_TIMEOUT) { hlptim->State = HAL_LPTIM_STATE_TIMEOUT; } __HAL_LPTIM_CLEAR_FLAG(hlptim, LPTIM_FLAG_ARROK); } /* Restore LPTIM source kernel clock */ switch ((uint32_t)hlptim->Instance) { case LPTIM1_BASE: __HAL_RCC_LPTIM1_CONFIG(tmpclksource); break; default: break; } } /* Restore configuration registers (LPTIM should be disabled first) */ hlptim->Instance->CR &= ~(LPTIM_CR_ENABLE); hlptim->Instance->IER = tmpIER; hlptim->Instance->CFGR = tmpCFGR; hlptim->Instance->OR = tmpOR; /* Exit critical section: restore previous priority mask */ __set_PRIMASK(primask_bit); } /** * @} */ #endif /* HAL_LPTIM_MODULE_ENABLED */ /** * @} */ /** * @} */