/** ****************************************************************************** * @file stm32f0xx_ll_i2c.h * @author MCD Application Team * @brief Header file of I2C LL module. ****************************************************************************** * @attention * * Copyright (c) 2016 STMicroelectronics. * All rights reserved. * * This software is licensed under terms that can be found in the LICENSE file * in the root directory of this software component. * If no LICENSE file comes with this software, it is provided AS-IS. * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef STM32F0xx_LL_I2C_H #define STM32F0xx_LL_I2C_H #ifdef __cplusplus extern "C" { #endif /* Includes ------------------------------------------------------------------*/ #include "stm32f0xx.h" /** @addtogroup STM32F0xx_LL_Driver * @{ */ #if defined (I2C1) || defined (I2C2) /** @defgroup I2C_LL I2C * @{ */ /* Private types -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /* Private constants ---------------------------------------------------------*/ /** @defgroup I2C_LL_Private_Constants I2C Private Constants * @{ */ /** * @} */ /* Private macros ------------------------------------------------------------*/ #if defined(USE_FULL_LL_DRIVER) /** @defgroup I2C_LL_Private_Macros I2C Private Macros * @{ */ /** * @} */ #endif /*USE_FULL_LL_DRIVER*/ /* Exported types ------------------------------------------------------------*/ #if defined(USE_FULL_LL_DRIVER) /** @defgroup I2C_LL_ES_INIT I2C Exported Init structure * @{ */ typedef struct { uint32_t PeripheralMode; /*!< Specifies the peripheral mode. This parameter can be a value of @ref I2C_LL_EC_PERIPHERAL_MODE. This feature can be modified afterwards using unitary function @ref LL_I2C_SetMode(). */ uint32_t Timing; /*!< Specifies the SDA setup, hold time and the SCL high, low period values. This parameter must be set by referring to the STM32CubeMX Tool and the helper macro @ref __LL_I2C_CONVERT_TIMINGS(). This feature can be modified afterwards using unitary function @ref LL_I2C_SetTiming(). */ uint32_t AnalogFilter; /*!< Enables or disables analog noise filter. This parameter can be a value of @ref I2C_LL_EC_ANALOGFILTER_SELECTION. This feature can be modified afterwards using unitary functions @ref LL_I2C_EnableAnalogFilter() or LL_I2C_DisableAnalogFilter(). */ uint32_t DigitalFilter; /*!< Configures the digital noise filter. This parameter can be a number between Min_Data = 0x00 and Max_Data = 0x0F. This feature can be modified afterwards using unitary function @ref LL_I2C_SetDigitalFilter(). */ uint32_t OwnAddress1; /*!< Specifies the device own address 1. This parameter must be a value between Min_Data = 0x00 and Max_Data = 0x3FF. This feature can be modified afterwards using unitary function @ref LL_I2C_SetOwnAddress1(). */ uint32_t TypeAcknowledge; /*!< Specifies the ACKnowledge or Non ACKnowledge condition after the address receive match code or next received byte. This parameter can be a value of @ref I2C_LL_EC_I2C_ACKNOWLEDGE. This feature can be modified afterwards using unitary function @ref LL_I2C_AcknowledgeNextData(). */ uint32_t OwnAddrSize; /*!< Specifies the device own address 1 size (7-bit or 10-bit). This parameter can be a value of @ref I2C_LL_EC_OWNADDRESS1. This feature can be modified afterwards using unitary function @ref LL_I2C_SetOwnAddress1(). */ } LL_I2C_InitTypeDef; /** * @} */ #endif /*USE_FULL_LL_DRIVER*/ /* Exported constants --------------------------------------------------------*/ /** @defgroup I2C_LL_Exported_Constants I2C Exported Constants * @{ */ /** @defgroup I2C_LL_EC_CLEAR_FLAG Clear Flags Defines * @brief Flags defines which can be used with LL_I2C_WriteReg function * @{ */ #define LL_I2C_ICR_ADDRCF I2C_ICR_ADDRCF /*!< Address Matched flag */ #define LL_I2C_ICR_NACKCF I2C_ICR_NACKCF /*!< Not Acknowledge flag */ #define LL_I2C_ICR_STOPCF I2C_ICR_STOPCF /*!< Stop detection flag */ #define LL_I2C_ICR_BERRCF I2C_ICR_BERRCF /*!< Bus error flag */ #define LL_I2C_ICR_ARLOCF I2C_ICR_ARLOCF /*!< Arbitration Lost flag */ #define LL_I2C_ICR_OVRCF I2C_ICR_OVRCF /*!< Overrun/Underrun flag */ #define LL_I2C_ICR_PECCF I2C_ICR_PECCF /*!< PEC error flag */ #define LL_I2C_ICR_TIMOUTCF I2C_ICR_TIMOUTCF /*!< Timeout detection flag */ #define LL_I2C_ICR_ALERTCF I2C_ICR_ALERTCF /*!< Alert flag */ /** * @} */ /** @defgroup I2C_LL_EC_GET_FLAG Get Flags Defines * @brief Flags defines which can be used with LL_I2C_ReadReg function * @{ */ #define LL_I2C_ISR_TXE I2C_ISR_TXE /*!< Transmit data register empty */ #define LL_I2C_ISR_TXIS I2C_ISR_TXIS /*!< Transmit interrupt status */ #define LL_I2C_ISR_RXNE I2C_ISR_RXNE /*!< Receive data register not empty */ #define LL_I2C_ISR_ADDR I2C_ISR_ADDR /*!< Address matched (slave mode) */ #define LL_I2C_ISR_NACKF I2C_ISR_NACKF /*!< Not Acknowledge received flag */ #define LL_I2C_ISR_STOPF I2C_ISR_STOPF /*!< Stop detection flag */ #define LL_I2C_ISR_TC I2C_ISR_TC /*!< Transfer Complete (master mode) */ #define LL_I2C_ISR_TCR I2C_ISR_TCR /*!< Transfer Complete Reload */ #define LL_I2C_ISR_BERR I2C_ISR_BERR /*!< Bus error */ #define LL_I2C_ISR_ARLO I2C_ISR_ARLO /*!< Arbitration lost */ #define LL_I2C_ISR_OVR I2C_ISR_OVR /*!< Overrun/Underrun (slave mode) */ #define LL_I2C_ISR_PECERR I2C_ISR_PECERR /*!< PEC Error in reception (SMBus mode) */ #define LL_I2C_ISR_TIMEOUT I2C_ISR_TIMEOUT /*!< Timeout detection flag (SMBus mode) */ #define LL_I2C_ISR_ALERT I2C_ISR_ALERT /*!< SMBus alert (SMBus mode) */ #define LL_I2C_ISR_BUSY I2C_ISR_BUSY /*!< Bus busy */ /** * @} */ /** @defgroup I2C_LL_EC_IT IT Defines * @brief IT defines which can be used with LL_I2C_ReadReg and LL_I2C_WriteReg functions * @{ */ #define LL_I2C_CR1_TXIE I2C_CR1_TXIE /*!< TX Interrupt enable */ #define LL_I2C_CR1_RXIE I2C_CR1_RXIE /*!< RX Interrupt enable */ #define LL_I2C_CR1_ADDRIE I2C_CR1_ADDRIE /*!< Address match Interrupt enable (slave only) */ #define LL_I2C_CR1_NACKIE I2C_CR1_NACKIE /*!< Not acknowledge received Interrupt enable */ #define LL_I2C_CR1_STOPIE I2C_CR1_STOPIE /*!< STOP detection Interrupt enable */ #define LL_I2C_CR1_TCIE I2C_CR1_TCIE /*!< Transfer Complete interrupt enable */ #define LL_I2C_CR1_ERRIE I2C_CR1_ERRIE /*!< Error interrupts enable */ /** * @} */ /** @defgroup I2C_LL_EC_PERIPHERAL_MODE Peripheral Mode * @{ */ #define LL_I2C_MODE_I2C 0x00000000U /*!< I2C Master or Slave mode */ #define LL_I2C_MODE_SMBUS_HOST I2C_CR1_SMBHEN /*!< SMBus Host address acknowledge */ #define LL_I2C_MODE_SMBUS_DEVICE 0x00000000U /*!< SMBus Device default mode (Default address not acknowledge) */ #define LL_I2C_MODE_SMBUS_DEVICE_ARP I2C_CR1_SMBDEN /*!< SMBus Device Default address acknowledge */ /** * @} */ /** @defgroup I2C_LL_EC_ANALOGFILTER_SELECTION Analog Filter Selection * @{ */ #define LL_I2C_ANALOGFILTER_ENABLE 0x00000000U /*!< Analog filter is enabled. */ #define LL_I2C_ANALOGFILTER_DISABLE I2C_CR1_ANFOFF /*!< Analog filter is disabled. */ /** * @} */ /** @defgroup I2C_LL_EC_ADDRESSING_MODE Master Addressing Mode * @{ */ #define LL_I2C_ADDRESSING_MODE_7BIT 0x00000000U /*!< Master operates in 7-bit addressing mode. */ #define LL_I2C_ADDRESSING_MODE_10BIT I2C_CR2_ADD10 /*!< Master operates in 10-bit addressing mode.*/ /** * @} */ /** @defgroup I2C_LL_EC_OWNADDRESS1 Own Address 1 Length * @{ */ #define LL_I2C_OWNADDRESS1_7BIT 0x00000000U /*!< Own address 1 is a 7-bit address. */ #define LL_I2C_OWNADDRESS1_10BIT I2C_OAR1_OA1MODE /*!< Own address 1 is a 10-bit address.*/ /** * @} */ /** @defgroup I2C_LL_EC_OWNADDRESS2 Own Address 2 Masks * @{ */ #define LL_I2C_OWNADDRESS2_NOMASK I2C_OAR2_OA2NOMASK /*!< Own Address2 No mask. */ #define LL_I2C_OWNADDRESS2_MASK01 I2C_OAR2_OA2MASK01 /*!< Only Address2 bits[7:2] are compared. */ #define LL_I2C_OWNADDRESS2_MASK02 I2C_OAR2_OA2MASK02 /*!< Only Address2 bits[7:3] are compared. */ #define LL_I2C_OWNADDRESS2_MASK03 I2C_OAR2_OA2MASK03 /*!< Only Address2 bits[7:4] are compared. */ #define LL_I2C_OWNADDRESS2_MASK04 I2C_OAR2_OA2MASK04 /*!< Only Address2 bits[7:5] are compared. */ #define LL_I2C_OWNADDRESS2_MASK05 I2C_OAR2_OA2MASK05 /*!< Only Address2 bits[7:6] are compared. */ #define LL_I2C_OWNADDRESS2_MASK06 I2C_OAR2_OA2MASK06 /*!< Only Address2 bits[7] are compared. */ #define LL_I2C_OWNADDRESS2_MASK07 I2C_OAR2_OA2MASK07 /*!< No comparison is done. All Address2 are acknowledged. */ /** * @} */ /** @defgroup I2C_LL_EC_I2C_ACKNOWLEDGE Acknowledge Generation * @{ */ #define LL_I2C_ACK 0x00000000U /*!< ACK is sent after current received byte. */ #define LL_I2C_NACK I2C_CR2_NACK /*!< NACK is sent after current received byte.*/ /** * @} */ /** @defgroup I2C_LL_EC_ADDRSLAVE Slave Address Length * @{ */ #define LL_I2C_ADDRSLAVE_7BIT 0x00000000U /*!< Slave Address in 7-bit. */ #define LL_I2C_ADDRSLAVE_10BIT I2C_CR2_ADD10 /*!< Slave Address in 10-bit.*/ /** * @} */ /** @defgroup I2C_LL_EC_REQUEST Transfer Request Direction * @{ */ #define LL_I2C_REQUEST_WRITE 0x00000000U /*!< Master request a write transfer. */ #define LL_I2C_REQUEST_READ I2C_CR2_RD_WRN /*!< Master request a read transfer. */ /** * @} */ /** @defgroup I2C_LL_EC_MODE Transfer End Mode * @{ */ #define LL_I2C_MODE_RELOAD I2C_CR2_RELOAD /*!< Enable I2C Reload mode. */ #define LL_I2C_MODE_AUTOEND I2C_CR2_AUTOEND /*!< Enable I2C Automatic end mode with no HW PEC comparison. */ #define LL_I2C_MODE_SOFTEND 0x00000000U /*!< Enable I2C Software end mode with no HW PEC comparison. */ #define LL_I2C_MODE_SMBUS_RELOAD LL_I2C_MODE_RELOAD /*!< Enable SMBUS Automatic end mode with HW PEC comparison. */ #define LL_I2C_MODE_SMBUS_AUTOEND_NO_PEC LL_I2C_MODE_AUTOEND /*!< Enable SMBUS Automatic end mode with HW PEC comparison. */ #define LL_I2C_MODE_SMBUS_SOFTEND_NO_PEC LL_I2C_MODE_SOFTEND /*!< Enable SMBUS Software end mode with HW PEC comparison. */ #define LL_I2C_MODE_SMBUS_AUTOEND_WITH_PEC (uint32_t)(LL_I2C_MODE_AUTOEND | I2C_CR2_PECBYTE) /*!< Enable SMBUS Automatic end mode with HW PEC comparison. */ #define LL_I2C_MODE_SMBUS_SOFTEND_WITH_PEC (uint32_t)(LL_I2C_MODE_SOFTEND | I2C_CR2_PECBYTE) /*!< Enable SMBUS Software end mode with HW PEC comparison. */ /** * @} */ /** @defgroup I2C_LL_EC_GENERATE Start And Stop Generation * @{ */ #define LL_I2C_GENERATE_NOSTARTSTOP 0x00000000U /*!< Don't Generate Stop and Start condition. */ #define LL_I2C_GENERATE_STOP (uint32_t)(0x80000000U | I2C_CR2_STOP) /*!< Generate Stop condition (Size should be set to 0). */ #define LL_I2C_GENERATE_START_READ (uint32_t)(0x80000000U | I2C_CR2_START | I2C_CR2_RD_WRN) /*!< Generate Start for read request. */ #define LL_I2C_GENERATE_START_WRITE (uint32_t)(0x80000000U | I2C_CR2_START) /*!< Generate Start for write request. */ #define LL_I2C_GENERATE_RESTART_7BIT_READ (uint32_t)(0x80000000U | I2C_CR2_START | I2C_CR2_RD_WRN) /*!< Generate Restart for read request, slave 7Bit address. */ #define LL_I2C_GENERATE_RESTART_7BIT_WRITE (uint32_t)(0x80000000U | I2C_CR2_START) /*!< Generate Restart for write request, slave 7Bit address. */ #define LL_I2C_GENERATE_RESTART_10BIT_READ (uint32_t)(0x80000000U | I2C_CR2_START | \ I2C_CR2_RD_WRN | I2C_CR2_HEAD10R) /*!< Generate Restart for read request, slave 10Bit address. */ #define LL_I2C_GENERATE_RESTART_10BIT_WRITE (uint32_t)(0x80000000U | I2C_CR2_START) /*!< Generate Restart for write request, slave 10Bit address.*/ /** * @} */ /** @defgroup I2C_LL_EC_DIRECTION Read Write Direction * @{ */ #define LL_I2C_DIRECTION_WRITE 0x00000000U /*!< Write transfer request by master, slave enters receiver mode. */ #define LL_I2C_DIRECTION_READ I2C_ISR_DIR /*!< Read transfer request by master, slave enters transmitter mode.*/ /** * @} */ /** @defgroup I2C_LL_EC_DMA_REG_DATA DMA Register Data * @{ */ #define LL_I2C_DMA_REG_DATA_TRANSMIT 0x00000000U /*!< Get address of data register used for transmission */ #define LL_I2C_DMA_REG_DATA_RECEIVE 0x00000001U /*!< Get address of data register used for reception */ /** * @} */ /** @defgroup I2C_LL_EC_SMBUS_TIMEOUTA_MODE SMBus TimeoutA Mode SCL SDA Timeout * @{ */ #define LL_I2C_SMBUS_TIMEOUTA_MODE_SCL_LOW 0x00000000U /*!< TimeoutA is used to detect SCL low level timeout. */ #define LL_I2C_SMBUS_TIMEOUTA_MODE_SDA_SCL_HIGH I2C_TIMEOUTR_TIDLE /*!< TimeoutA is used to detect both SCL and SDA high level timeout.*/ /** * @} */ /** @defgroup I2C_LL_EC_SMBUS_TIMEOUT_SELECTION SMBus Timeout Selection * @{ */ #define LL_I2C_SMBUS_TIMEOUTA I2C_TIMEOUTR_TIMOUTEN /*!< TimeoutA enable bit */ #define LL_I2C_SMBUS_TIMEOUTB I2C_TIMEOUTR_TEXTEN /*!< TimeoutB (extended clock) enable bit */ #define LL_I2C_SMBUS_ALL_TIMEOUT (uint32_t)(I2C_TIMEOUTR_TIMOUTEN | \ I2C_TIMEOUTR_TEXTEN) /*!< TimeoutA and TimeoutB (extended clock) enable bits */ /** * @} */ /** * @} */ /* Exported macro ------------------------------------------------------------*/ /** @defgroup I2C_LL_Exported_Macros I2C Exported Macros * @{ */ /** @defgroup I2C_LL_EM_WRITE_READ Common Write and read registers Macros * @{ */ /** * @brief Write a value in I2C register * @param __INSTANCE__ I2C Instance * @param __REG__ Register to be written * @param __VALUE__ Value to be written in the register * @retval None */ #define LL_I2C_WriteReg(__INSTANCE__, __REG__, __VALUE__) WRITE_REG(__INSTANCE__->__REG__, (__VALUE__)) /** * @brief Read a value in I2C register * @param __INSTANCE__ I2C Instance * @param __REG__ Register to be read * @retval Register value */ #define LL_I2C_ReadReg(__INSTANCE__, __REG__) READ_REG(__INSTANCE__->__REG__) /** * @} */ /** @defgroup I2C_LL_EM_CONVERT_TIMINGS Convert SDA SCL timings * @{ */ /** * @brief Configure the SDA setup, hold time and the SCL high, low period. * @param __PRESCALER__ This parameter must be a value between Min_Data=0 and Max_Data=0xF. * @param __SETUP_TIME__ This parameter must be a value between Min_Data=0 and Max_Data=0xF. (tscldel = (SCLDEL+1)xtpresc) * @param __HOLD_TIME__ This parameter must be a value between Min_Data=0 and Max_Data=0xF. (tsdadel = SDADELxtpresc) * @param __SCLH_PERIOD__ This parameter must be a value between Min_Data=0 and Max_Data=0xFF. (tsclh = (SCLH+1)xtpresc) * @param __SCLL_PERIOD__ This parameter must be a value between Min_Data=0 and Max_Data=0xFF. (tscll = (SCLL+1)xtpresc) * @retval Value between Min_Data=0 and Max_Data=0xFFFFFFFF */ #define __LL_I2C_CONVERT_TIMINGS(__PRESCALER__, __SETUP_TIME__, __HOLD_TIME__, __SCLH_PERIOD__, __SCLL_PERIOD__) \ ((((uint32_t)(__PRESCALER__) << I2C_TIMINGR_PRESC_Pos) & I2C_TIMINGR_PRESC) | \ (((uint32_t)(__SETUP_TIME__) << I2C_TIMINGR_SCLDEL_Pos) & I2C_TIMINGR_SCLDEL) | \ (((uint32_t)(__HOLD_TIME__) << I2C_TIMINGR_SDADEL_Pos) & I2C_TIMINGR_SDADEL) | \ (((uint32_t)(__SCLH_PERIOD__) << I2C_TIMINGR_SCLH_Pos) & I2C_TIMINGR_SCLH) | \ (((uint32_t)(__SCLL_PERIOD__) << I2C_TIMINGR_SCLL_Pos) & I2C_TIMINGR_SCLL)) /** * @} */ /** * @} */ /* Exported functions --------------------------------------------------------*/ /** @defgroup I2C_LL_Exported_Functions I2C Exported Functions * @{ */ /** @defgroup I2C_LL_EF_Configuration Configuration * @{ */ /** * @brief Enable I2C peripheral (PE = 1). * @rmtoll CR1 PE LL_I2C_Enable * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_Enable(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_PE); } /** * @brief Disable I2C peripheral (PE = 0). * @note When PE = 0, the I2C SCL and SDA lines are released. * Internal state machines and status bits are put back to their reset value. * When cleared, PE must be kept low for at least 3 APB clock cycles. * @rmtoll CR1 PE LL_I2C_Disable * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_Disable(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_PE); } /** * @brief Check if the I2C peripheral is enabled or disabled. * @rmtoll CR1 PE LL_I2C_IsEnabled * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabled(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_PE) == (I2C_CR1_PE)) ? 1UL : 0UL); } /** * @brief Configure Noise Filters (Analog and Digital). * @note If the analog filter is also enabled, the digital filter is added to analog filter. * The filters can only be programmed when the I2C is disabled (PE = 0). * @rmtoll CR1 ANFOFF LL_I2C_ConfigFilters\n * CR1 DNF LL_I2C_ConfigFilters * @param I2Cx I2C Instance. * @param AnalogFilter This parameter can be one of the following values: * @arg @ref LL_I2C_ANALOGFILTER_ENABLE * @arg @ref LL_I2C_ANALOGFILTER_DISABLE * @param DigitalFilter This parameter must be a value between Min_Data=0x00 (Digital filter disabled) and Max_Data=0x0F (Digital filter enabled and filtering capability up to 15*ti2cclk). * This parameter is used to configure the digital noise filter on SDA and SCL input. * The digital filter will filter spikes with a length of up to DNF[3:0]*ti2cclk. * @retval None */ __STATIC_INLINE void LL_I2C_ConfigFilters(I2C_TypeDef *I2Cx, uint32_t AnalogFilter, uint32_t DigitalFilter) { MODIFY_REG(I2Cx->CR1, I2C_CR1_ANFOFF | I2C_CR1_DNF, AnalogFilter | (DigitalFilter << I2C_CR1_DNF_Pos)); } /** * @brief Configure Digital Noise Filter. * @note If the analog filter is also enabled, the digital filter is added to analog filter. * This filter can only be programmed when the I2C is disabled (PE = 0). * @rmtoll CR1 DNF LL_I2C_SetDigitalFilter * @param I2Cx I2C Instance. * @param DigitalFilter This parameter must be a value between Min_Data=0x00 (Digital filter disabled) and Max_Data=0x0F (Digital filter enabled and filtering capability up to 15*ti2cclk). * This parameter is used to configure the digital noise filter on SDA and SCL input. * The digital filter will filter spikes with a length of up to DNF[3:0]*ti2cclk. * @retval None */ __STATIC_INLINE void LL_I2C_SetDigitalFilter(I2C_TypeDef *I2Cx, uint32_t DigitalFilter) { MODIFY_REG(I2Cx->CR1, I2C_CR1_DNF, DigitalFilter << I2C_CR1_DNF_Pos); } /** * @brief Get the current Digital Noise Filter configuration. * @rmtoll CR1 DNF LL_I2C_GetDigitalFilter * @param I2Cx I2C Instance. * @retval Value between Min_Data=0x0 and Max_Data=0xF */ __STATIC_INLINE uint32_t LL_I2C_GetDigitalFilter(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->CR1, I2C_CR1_DNF) >> I2C_CR1_DNF_Pos); } /** * @brief Enable Analog Noise Filter. * @note This filter can only be programmed when the I2C is disabled (PE = 0). * @rmtoll CR1 ANFOFF LL_I2C_EnableAnalogFilter * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableAnalogFilter(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_ANFOFF); } /** * @brief Disable Analog Noise Filter. * @note This filter can only be programmed when the I2C is disabled (PE = 0). * @rmtoll CR1 ANFOFF LL_I2C_DisableAnalogFilter * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableAnalogFilter(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_ANFOFF); } /** * @brief Check if Analog Noise Filter is enabled or disabled. * @rmtoll CR1 ANFOFF LL_I2C_IsEnabledAnalogFilter * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledAnalogFilter(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_ANFOFF) != (I2C_CR1_ANFOFF)) ? 1UL : 0UL); } /** * @brief Enable DMA transmission requests. * @rmtoll CR1 TXDMAEN LL_I2C_EnableDMAReq_TX * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableDMAReq_TX(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_TXDMAEN); } /** * @brief Disable DMA transmission requests. * @rmtoll CR1 TXDMAEN LL_I2C_DisableDMAReq_TX * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableDMAReq_TX(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_TXDMAEN); } /** * @brief Check if DMA transmission requests are enabled or disabled. * @rmtoll CR1 TXDMAEN LL_I2C_IsEnabledDMAReq_TX * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledDMAReq_TX(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_TXDMAEN) == (I2C_CR1_TXDMAEN)) ? 1UL : 0UL); } /** * @brief Enable DMA reception requests. * @rmtoll CR1 RXDMAEN LL_I2C_EnableDMAReq_RX * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableDMAReq_RX(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_RXDMAEN); } /** * @brief Disable DMA reception requests. * @rmtoll CR1 RXDMAEN LL_I2C_DisableDMAReq_RX * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableDMAReq_RX(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_RXDMAEN); } /** * @brief Check if DMA reception requests are enabled or disabled. * @rmtoll CR1 RXDMAEN LL_I2C_IsEnabledDMAReq_RX * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledDMAReq_RX(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_RXDMAEN) == (I2C_CR1_RXDMAEN)) ? 1UL : 0UL); } /** * @brief Get the data register address used for DMA transfer * @rmtoll TXDR TXDATA LL_I2C_DMA_GetRegAddr\n * RXDR RXDATA LL_I2C_DMA_GetRegAddr * @param I2Cx I2C Instance * @param Direction This parameter can be one of the following values: * @arg @ref LL_I2C_DMA_REG_DATA_TRANSMIT * @arg @ref LL_I2C_DMA_REG_DATA_RECEIVE * @retval Address of data register */ __STATIC_INLINE uint32_t LL_I2C_DMA_GetRegAddr(const I2C_TypeDef *I2Cx, uint32_t Direction) { uint32_t data_reg_addr; if (Direction == LL_I2C_DMA_REG_DATA_TRANSMIT) { /* return address of TXDR register */ data_reg_addr = (uint32_t) &(I2Cx->TXDR); } else { /* return address of RXDR register */ data_reg_addr = (uint32_t) &(I2Cx->RXDR); } return data_reg_addr; } /** * @brief Enable Clock stretching. * @note This bit can only be programmed when the I2C is disabled (PE = 0). * @rmtoll CR1 NOSTRETCH LL_I2C_EnableClockStretching * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableClockStretching(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH); } /** * @brief Disable Clock stretching. * @note This bit can only be programmed when the I2C is disabled (PE = 0). * @rmtoll CR1 NOSTRETCH LL_I2C_DisableClockStretching * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableClockStretching(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH); } /** * @brief Check if Clock stretching is enabled or disabled. * @rmtoll CR1 NOSTRETCH LL_I2C_IsEnabledClockStretching * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledClockStretching(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_NOSTRETCH) != (I2C_CR1_NOSTRETCH)) ? 1UL : 0UL); } /** * @brief Enable hardware byte control in slave mode. * @rmtoll CR1 SBC LL_I2C_EnableSlaveByteControl * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableSlaveByteControl(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_SBC); } /** * @brief Disable hardware byte control in slave mode. * @rmtoll CR1 SBC LL_I2C_DisableSlaveByteControl * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableSlaveByteControl(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_SBC); } /** * @brief Check if hardware byte control in slave mode is enabled or disabled. * @rmtoll CR1 SBC LL_I2C_IsEnabledSlaveByteControl * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledSlaveByteControl(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_SBC) == (I2C_CR1_SBC)) ? 1UL : 0UL); } #if defined(I2C_CR1_WUPEN) /** * @brief Enable Wakeup from STOP. * @note The macro IS_I2C_WAKEUP_FROMSTOP_INSTANCE(I2Cx) can be used to check whether or not * WakeUpFromStop feature is supported by the I2Cx Instance. * @note This bit can only be programmed when Digital Filter is disabled. * @rmtoll CR1 WUPEN LL_I2C_EnableWakeUpFromStop * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableWakeUpFromStop(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_WUPEN); } /** * @brief Disable Wakeup from STOP. * @note The macro IS_I2C_WAKEUP_FROMSTOP_INSTANCE(I2Cx) can be used to check whether or not * WakeUpFromStop feature is supported by the I2Cx Instance. * @rmtoll CR1 WUPEN LL_I2C_DisableWakeUpFromStop * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableWakeUpFromStop(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_WUPEN); } /** * @brief Check if Wakeup from STOP is enabled or disabled. * @note The macro IS_I2C_WAKEUP_FROMSTOP_INSTANCE(I2Cx) can be used to check whether or not * WakeUpFromStop feature is supported by the I2Cx Instance. * @rmtoll CR1 WUPEN LL_I2C_IsEnabledWakeUpFromStop * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledWakeUpFromStop(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_WUPEN) == (I2C_CR1_WUPEN)) ? 1UL : 0UL); } #endif /* I2C_CR1_WUPEN */ /** * @brief Enable General Call. * @note When enabled the Address 0x00 is ACKed. * @rmtoll CR1 GCEN LL_I2C_EnableGeneralCall * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableGeneralCall(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_GCEN); } /** * @brief Disable General Call. * @note When disabled the Address 0x00 is NACKed. * @rmtoll CR1 GCEN LL_I2C_DisableGeneralCall * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableGeneralCall(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_GCEN); } /** * @brief Check if General Call is enabled or disabled. * @rmtoll CR1 GCEN LL_I2C_IsEnabledGeneralCall * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledGeneralCall(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_GCEN) == (I2C_CR1_GCEN)) ? 1UL : 0UL); } /** * @brief Configure the Master to operate in 7-bit or 10-bit addressing mode. * @note Changing this bit is not allowed, when the START bit is set. * @rmtoll CR2 ADD10 LL_I2C_SetMasterAddressingMode * @param I2Cx I2C Instance. * @param AddressingMode This parameter can be one of the following values: * @arg @ref LL_I2C_ADDRESSING_MODE_7BIT * @arg @ref LL_I2C_ADDRESSING_MODE_10BIT * @retval None */ __STATIC_INLINE void LL_I2C_SetMasterAddressingMode(I2C_TypeDef *I2Cx, uint32_t AddressingMode) { MODIFY_REG(I2Cx->CR2, I2C_CR2_ADD10, AddressingMode); } /** * @brief Get the Master addressing mode. * @rmtoll CR2 ADD10 LL_I2C_GetMasterAddressingMode * @param I2Cx I2C Instance. * @retval Returned value can be one of the following values: * @arg @ref LL_I2C_ADDRESSING_MODE_7BIT * @arg @ref LL_I2C_ADDRESSING_MODE_10BIT */ __STATIC_INLINE uint32_t LL_I2C_GetMasterAddressingMode(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->CR2, I2C_CR2_ADD10)); } /** * @brief Set the Own Address1. * @rmtoll OAR1 OA1 LL_I2C_SetOwnAddress1\n * OAR1 OA1MODE LL_I2C_SetOwnAddress1 * @param I2Cx I2C Instance. * @param OwnAddress1 This parameter must be a value between Min_Data=0 and Max_Data=0x3FF. * @param OwnAddrSize This parameter can be one of the following values: * @arg @ref LL_I2C_OWNADDRESS1_7BIT * @arg @ref LL_I2C_OWNADDRESS1_10BIT * @retval None */ __STATIC_INLINE void LL_I2C_SetOwnAddress1(I2C_TypeDef *I2Cx, uint32_t OwnAddress1, uint32_t OwnAddrSize) { MODIFY_REG(I2Cx->OAR1, I2C_OAR1_OA1 | I2C_OAR1_OA1MODE, OwnAddress1 | OwnAddrSize); } /** * @brief Enable acknowledge on Own Address1 match address. * @rmtoll OAR1 OA1EN LL_I2C_EnableOwnAddress1 * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableOwnAddress1(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->OAR1, I2C_OAR1_OA1EN); } /** * @brief Disable acknowledge on Own Address1 match address. * @rmtoll OAR1 OA1EN LL_I2C_DisableOwnAddress1 * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableOwnAddress1(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->OAR1, I2C_OAR1_OA1EN); } /** * @brief Check if Own Address1 acknowledge is enabled or disabled. * @rmtoll OAR1 OA1EN LL_I2C_IsEnabledOwnAddress1 * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledOwnAddress1(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->OAR1, I2C_OAR1_OA1EN) == (I2C_OAR1_OA1EN)) ? 1UL : 0UL); } /** * @brief Set the 7bits Own Address2. * @note This action has no effect if own address2 is enabled. * @rmtoll OAR2 OA2 LL_I2C_SetOwnAddress2\n * OAR2 OA2MSK LL_I2C_SetOwnAddress2 * @param I2Cx I2C Instance. * @param OwnAddress2 Value between Min_Data=0 and Max_Data=0x7F. * @param OwnAddrMask This parameter can be one of the following values: * @arg @ref LL_I2C_OWNADDRESS2_NOMASK * @arg @ref LL_I2C_OWNADDRESS2_MASK01 * @arg @ref LL_I2C_OWNADDRESS2_MASK02 * @arg @ref LL_I2C_OWNADDRESS2_MASK03 * @arg @ref LL_I2C_OWNADDRESS2_MASK04 * @arg @ref LL_I2C_OWNADDRESS2_MASK05 * @arg @ref LL_I2C_OWNADDRESS2_MASK06 * @arg @ref LL_I2C_OWNADDRESS2_MASK07 * @retval None */ __STATIC_INLINE void LL_I2C_SetOwnAddress2(I2C_TypeDef *I2Cx, uint32_t OwnAddress2, uint32_t OwnAddrMask) { MODIFY_REG(I2Cx->OAR2, I2C_OAR2_OA2 | I2C_OAR2_OA2MSK, OwnAddress2 | OwnAddrMask); } /** * @brief Enable acknowledge on Own Address2 match address. * @rmtoll OAR2 OA2EN LL_I2C_EnableOwnAddress2 * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableOwnAddress2(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->OAR2, I2C_OAR2_OA2EN); } /** * @brief Disable acknowledge on Own Address2 match address. * @rmtoll OAR2 OA2EN LL_I2C_DisableOwnAddress2 * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableOwnAddress2(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->OAR2, I2C_OAR2_OA2EN); } /** * @brief Check if Own Address1 acknowledge is enabled or disabled. * @rmtoll OAR2 OA2EN LL_I2C_IsEnabledOwnAddress2 * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledOwnAddress2(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->OAR2, I2C_OAR2_OA2EN) == (I2C_OAR2_OA2EN)) ? 1UL : 0UL); } /** * @brief Configure the SDA setup, hold time and the SCL high, low period. * @note This bit can only be programmed when the I2C is disabled (PE = 0). * @rmtoll TIMINGR TIMINGR LL_I2C_SetTiming * @param I2Cx I2C Instance. * @param Timing This parameter must be a value between Min_Data=0 and Max_Data=0xFFFFFFFF. * @note This parameter is computed with the STM32CubeMX Tool. * @retval None */ __STATIC_INLINE void LL_I2C_SetTiming(I2C_TypeDef *I2Cx, uint32_t Timing) { WRITE_REG(I2Cx->TIMINGR, Timing); } /** * @brief Get the Timing Prescaler setting. * @rmtoll TIMINGR PRESC LL_I2C_GetTimingPrescaler * @param I2Cx I2C Instance. * @retval Value between Min_Data=0x0 and Max_Data=0xF */ __STATIC_INLINE uint32_t LL_I2C_GetTimingPrescaler(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->TIMINGR, I2C_TIMINGR_PRESC) >> I2C_TIMINGR_PRESC_Pos); } /** * @brief Get the SCL low period setting. * @rmtoll TIMINGR SCLL LL_I2C_GetClockLowPeriod * @param I2Cx I2C Instance. * @retval Value between Min_Data=0x00 and Max_Data=0xFF */ __STATIC_INLINE uint32_t LL_I2C_GetClockLowPeriod(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->TIMINGR, I2C_TIMINGR_SCLL) >> I2C_TIMINGR_SCLL_Pos); } /** * @brief Get the SCL high period setting. * @rmtoll TIMINGR SCLH LL_I2C_GetClockHighPeriod * @param I2Cx I2C Instance. * @retval Value between Min_Data=0x00 and Max_Data=0xFF */ __STATIC_INLINE uint32_t LL_I2C_GetClockHighPeriod(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->TIMINGR, I2C_TIMINGR_SCLH) >> I2C_TIMINGR_SCLH_Pos); } /** * @brief Get the SDA hold time. * @rmtoll TIMINGR SDADEL LL_I2C_GetDataHoldTime * @param I2Cx I2C Instance. * @retval Value between Min_Data=0x0 and Max_Data=0xF */ __STATIC_INLINE uint32_t LL_I2C_GetDataHoldTime(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->TIMINGR, I2C_TIMINGR_SDADEL) >> I2C_TIMINGR_SDADEL_Pos); } /** * @brief Get the SDA setup time. * @rmtoll TIMINGR SCLDEL LL_I2C_GetDataSetupTime * @param I2Cx I2C Instance. * @retval Value between Min_Data=0x0 and Max_Data=0xF */ __STATIC_INLINE uint32_t LL_I2C_GetDataSetupTime(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->TIMINGR, I2C_TIMINGR_SCLDEL) >> I2C_TIMINGR_SCLDEL_Pos); } /** * @brief Configure peripheral mode. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll CR1 SMBHEN LL_I2C_SetMode\n * CR1 SMBDEN LL_I2C_SetMode * @param I2Cx I2C Instance. * @param PeripheralMode This parameter can be one of the following values: * @arg @ref LL_I2C_MODE_I2C * @arg @ref LL_I2C_MODE_SMBUS_HOST * @arg @ref LL_I2C_MODE_SMBUS_DEVICE * @arg @ref LL_I2C_MODE_SMBUS_DEVICE_ARP * @retval None */ __STATIC_INLINE void LL_I2C_SetMode(I2C_TypeDef *I2Cx, uint32_t PeripheralMode) { MODIFY_REG(I2Cx->CR1, I2C_CR1_SMBHEN | I2C_CR1_SMBDEN, PeripheralMode); } /** * @brief Get peripheral mode. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll CR1 SMBHEN LL_I2C_GetMode\n * CR1 SMBDEN LL_I2C_GetMode * @param I2Cx I2C Instance. * @retval Returned value can be one of the following values: * @arg @ref LL_I2C_MODE_I2C * @arg @ref LL_I2C_MODE_SMBUS_HOST * @arg @ref LL_I2C_MODE_SMBUS_DEVICE * @arg @ref LL_I2C_MODE_SMBUS_DEVICE_ARP */ __STATIC_INLINE uint32_t LL_I2C_GetMode(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->CR1, I2C_CR1_SMBHEN | I2C_CR1_SMBDEN)); } /** * @brief Enable SMBus alert (Host or Device mode) * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @note SMBus Device mode: * - SMBus Alert pin is drived low and * Alert Response Address Header acknowledge is enabled. * SMBus Host mode: * - SMBus Alert pin management is supported. * @rmtoll CR1 ALERTEN LL_I2C_EnableSMBusAlert * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableSMBusAlert(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_ALERTEN); } /** * @brief Disable SMBus alert (Host or Device mode) * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @note SMBus Device mode: * - SMBus Alert pin is not drived (can be used as a standard GPIO) and * Alert Response Address Header acknowledge is disabled. * SMBus Host mode: * - SMBus Alert pin management is not supported. * @rmtoll CR1 ALERTEN LL_I2C_DisableSMBusAlert * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableSMBusAlert(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_ALERTEN); } /** * @brief Check if SMBus alert (Host or Device mode) is enabled or disabled. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll CR1 ALERTEN LL_I2C_IsEnabledSMBusAlert * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusAlert(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_ALERTEN) == (I2C_CR1_ALERTEN)) ? 1UL : 0UL); } /** * @brief Enable SMBus Packet Error Calculation (PEC). * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll CR1 PECEN LL_I2C_EnableSMBusPEC * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableSMBusPEC(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_PECEN); } /** * @brief Disable SMBus Packet Error Calculation (PEC). * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll CR1 PECEN LL_I2C_DisableSMBusPEC * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableSMBusPEC(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_PECEN); } /** * @brief Check if SMBus Packet Error Calculation (PEC) is enabled or disabled. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll CR1 PECEN LL_I2C_IsEnabledSMBusPEC * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusPEC(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_PECEN) == (I2C_CR1_PECEN)) ? 1UL : 0UL); } /** * @brief Configure the SMBus Clock Timeout. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @note This configuration can only be programmed when associated Timeout is disabled (TimeoutA and/orTimeoutB). * @rmtoll TIMEOUTR TIMEOUTA LL_I2C_ConfigSMBusTimeout\n * TIMEOUTR TIDLE LL_I2C_ConfigSMBusTimeout\n * TIMEOUTR TIMEOUTB LL_I2C_ConfigSMBusTimeout * @param I2Cx I2C Instance. * @param TimeoutA This parameter must be a value between Min_Data=0 and Max_Data=0xFFF. * @param TimeoutAMode This parameter can be one of the following values: * @arg @ref LL_I2C_SMBUS_TIMEOUTA_MODE_SCL_LOW * @arg @ref LL_I2C_SMBUS_TIMEOUTA_MODE_SDA_SCL_HIGH * @param TimeoutB * @retval None */ __STATIC_INLINE void LL_I2C_ConfigSMBusTimeout(I2C_TypeDef *I2Cx, uint32_t TimeoutA, uint32_t TimeoutAMode, uint32_t TimeoutB) { MODIFY_REG(I2Cx->TIMEOUTR, I2C_TIMEOUTR_TIMEOUTA | I2C_TIMEOUTR_TIDLE | I2C_TIMEOUTR_TIMEOUTB, TimeoutA | TimeoutAMode | (TimeoutB << I2C_TIMEOUTR_TIMEOUTB_Pos)); } /** * @brief Configure the SMBus Clock TimeoutA (SCL low timeout or SCL and SDA high timeout depends on TimeoutA mode). * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @note These bits can only be programmed when TimeoutA is disabled. * @rmtoll TIMEOUTR TIMEOUTA LL_I2C_SetSMBusTimeoutA * @param I2Cx I2C Instance. * @param TimeoutA This parameter must be a value between Min_Data=0 and Max_Data=0xFFF. * @retval None */ __STATIC_INLINE void LL_I2C_SetSMBusTimeoutA(I2C_TypeDef *I2Cx, uint32_t TimeoutA) { WRITE_REG(I2Cx->TIMEOUTR, TimeoutA); } /** * @brief Get the SMBus Clock TimeoutA setting. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll TIMEOUTR TIMEOUTA LL_I2C_GetSMBusTimeoutA * @param I2Cx I2C Instance. * @retval Value between Min_Data=0 and Max_Data=0xFFF */ __STATIC_INLINE uint32_t LL_I2C_GetSMBusTimeoutA(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->TIMEOUTR, I2C_TIMEOUTR_TIMEOUTA)); } /** * @brief Set the SMBus Clock TimeoutA mode. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @note This bit can only be programmed when TimeoutA is disabled. * @rmtoll TIMEOUTR TIDLE LL_I2C_SetSMBusTimeoutAMode * @param I2Cx I2C Instance. * @param TimeoutAMode This parameter can be one of the following values: * @arg @ref LL_I2C_SMBUS_TIMEOUTA_MODE_SCL_LOW * @arg @ref LL_I2C_SMBUS_TIMEOUTA_MODE_SDA_SCL_HIGH * @retval None */ __STATIC_INLINE void LL_I2C_SetSMBusTimeoutAMode(I2C_TypeDef *I2Cx, uint32_t TimeoutAMode) { WRITE_REG(I2Cx->TIMEOUTR, TimeoutAMode); } /** * @brief Get the SMBus Clock TimeoutA mode. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll TIMEOUTR TIDLE LL_I2C_GetSMBusTimeoutAMode * @param I2Cx I2C Instance. * @retval Returned value can be one of the following values: * @arg @ref LL_I2C_SMBUS_TIMEOUTA_MODE_SCL_LOW * @arg @ref LL_I2C_SMBUS_TIMEOUTA_MODE_SDA_SCL_HIGH */ __STATIC_INLINE uint32_t LL_I2C_GetSMBusTimeoutAMode(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->TIMEOUTR, I2C_TIMEOUTR_TIDLE)); } /** * @brief Configure the SMBus Extended Cumulative Clock TimeoutB (Master or Slave mode). * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @note These bits can only be programmed when TimeoutB is disabled. * @rmtoll TIMEOUTR TIMEOUTB LL_I2C_SetSMBusTimeoutB * @param I2Cx I2C Instance. * @param TimeoutB This parameter must be a value between Min_Data=0 and Max_Data=0xFFF. * @retval None */ __STATIC_INLINE void LL_I2C_SetSMBusTimeoutB(I2C_TypeDef *I2Cx, uint32_t TimeoutB) { WRITE_REG(I2Cx->TIMEOUTR, TimeoutB << I2C_TIMEOUTR_TIMEOUTB_Pos); } /** * @brief Get the SMBus Extended Cumulative Clock TimeoutB setting. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll TIMEOUTR TIMEOUTB LL_I2C_GetSMBusTimeoutB * @param I2Cx I2C Instance. * @retval Value between Min_Data=0 and Max_Data=0xFFF */ __STATIC_INLINE uint32_t LL_I2C_GetSMBusTimeoutB(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->TIMEOUTR, I2C_TIMEOUTR_TIMEOUTB) >> I2C_TIMEOUTR_TIMEOUTB_Pos); } /** * @brief Enable the SMBus Clock Timeout. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll TIMEOUTR TIMOUTEN LL_I2C_EnableSMBusTimeout\n * TIMEOUTR TEXTEN LL_I2C_EnableSMBusTimeout * @param I2Cx I2C Instance. * @param ClockTimeout This parameter can be one of the following values: * @arg @ref LL_I2C_SMBUS_TIMEOUTA * @arg @ref LL_I2C_SMBUS_TIMEOUTB * @arg @ref LL_I2C_SMBUS_ALL_TIMEOUT * @retval None */ __STATIC_INLINE void LL_I2C_EnableSMBusTimeout(I2C_TypeDef *I2Cx, uint32_t ClockTimeout) { SET_BIT(I2Cx->TIMEOUTR, ClockTimeout); } /** * @brief Disable the SMBus Clock Timeout. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll TIMEOUTR TIMOUTEN LL_I2C_DisableSMBusTimeout\n * TIMEOUTR TEXTEN LL_I2C_DisableSMBusTimeout * @param I2Cx I2C Instance. * @param ClockTimeout This parameter can be one of the following values: * @arg @ref LL_I2C_SMBUS_TIMEOUTA * @arg @ref LL_I2C_SMBUS_TIMEOUTB * @arg @ref LL_I2C_SMBUS_ALL_TIMEOUT * @retval None */ __STATIC_INLINE void LL_I2C_DisableSMBusTimeout(I2C_TypeDef *I2Cx, uint32_t ClockTimeout) { CLEAR_BIT(I2Cx->TIMEOUTR, ClockTimeout); } /** * @brief Check if the SMBus Clock Timeout is enabled or disabled. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll TIMEOUTR TIMOUTEN LL_I2C_IsEnabledSMBusTimeout\n * TIMEOUTR TEXTEN LL_I2C_IsEnabledSMBusTimeout * @param I2Cx I2C Instance. * @param ClockTimeout This parameter can be one of the following values: * @arg @ref LL_I2C_SMBUS_TIMEOUTA * @arg @ref LL_I2C_SMBUS_TIMEOUTB * @arg @ref LL_I2C_SMBUS_ALL_TIMEOUT * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusTimeout(const I2C_TypeDef *I2Cx, uint32_t ClockTimeout) { return ((READ_BIT(I2Cx->TIMEOUTR, (I2C_TIMEOUTR_TIMOUTEN | I2C_TIMEOUTR_TEXTEN)) == \ (ClockTimeout)) ? 1UL : 0UL); } /** * @} */ /** @defgroup I2C_LL_EF_IT_Management IT_Management * @{ */ /** * @brief Enable TXIS interrupt. * @rmtoll CR1 TXIE LL_I2C_EnableIT_TX * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableIT_TX(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_TXIE); } /** * @brief Disable TXIS interrupt. * @rmtoll CR1 TXIE LL_I2C_DisableIT_TX * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableIT_TX(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_TXIE); } /** * @brief Check if the TXIS Interrupt is enabled or disabled. * @rmtoll CR1 TXIE LL_I2C_IsEnabledIT_TX * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_TX(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_TXIE) == (I2C_CR1_TXIE)) ? 1UL : 0UL); } /** * @brief Enable RXNE interrupt. * @rmtoll CR1 RXIE LL_I2C_EnableIT_RX * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableIT_RX(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_RXIE); } /** * @brief Disable RXNE interrupt. * @rmtoll CR1 RXIE LL_I2C_DisableIT_RX * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableIT_RX(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_RXIE); } /** * @brief Check if the RXNE Interrupt is enabled or disabled. * @rmtoll CR1 RXIE LL_I2C_IsEnabledIT_RX * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_RX(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_RXIE) == (I2C_CR1_RXIE)) ? 1UL : 0UL); } /** * @brief Enable Address match interrupt (slave mode only). * @rmtoll CR1 ADDRIE LL_I2C_EnableIT_ADDR * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableIT_ADDR(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_ADDRIE); } /** * @brief Disable Address match interrupt (slave mode only). * @rmtoll CR1 ADDRIE LL_I2C_DisableIT_ADDR * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableIT_ADDR(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_ADDRIE); } /** * @brief Check if Address match interrupt is enabled or disabled. * @rmtoll CR1 ADDRIE LL_I2C_IsEnabledIT_ADDR * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_ADDR(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_ADDRIE) == (I2C_CR1_ADDRIE)) ? 1UL : 0UL); } /** * @brief Enable Not acknowledge received interrupt. * @rmtoll CR1 NACKIE LL_I2C_EnableIT_NACK * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableIT_NACK(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_NACKIE); } /** * @brief Disable Not acknowledge received interrupt. * @rmtoll CR1 NACKIE LL_I2C_DisableIT_NACK * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableIT_NACK(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_NACKIE); } /** * @brief Check if Not acknowledge received interrupt is enabled or disabled. * @rmtoll CR1 NACKIE LL_I2C_IsEnabledIT_NACK * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_NACK(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_NACKIE) == (I2C_CR1_NACKIE)) ? 1UL : 0UL); } /** * @brief Enable STOP detection interrupt. * @rmtoll CR1 STOPIE LL_I2C_EnableIT_STOP * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableIT_STOP(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_STOPIE); } /** * @brief Disable STOP detection interrupt. * @rmtoll CR1 STOPIE LL_I2C_DisableIT_STOP * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableIT_STOP(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_STOPIE); } /** * @brief Check if STOP detection interrupt is enabled or disabled. * @rmtoll CR1 STOPIE LL_I2C_IsEnabledIT_STOP * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_STOP(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_STOPIE) == (I2C_CR1_STOPIE)) ? 1UL : 0UL); } /** * @brief Enable Transfer Complete interrupt. * @note Any of these events will generate interrupt : * Transfer Complete (TC) * Transfer Complete Reload (TCR) * @rmtoll CR1 TCIE LL_I2C_EnableIT_TC * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableIT_TC(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_TCIE); } /** * @brief Disable Transfer Complete interrupt. * @note Any of these events will generate interrupt : * Transfer Complete (TC) * Transfer Complete Reload (TCR) * @rmtoll CR1 TCIE LL_I2C_DisableIT_TC * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableIT_TC(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_TCIE); } /** * @brief Check if Transfer Complete interrupt is enabled or disabled. * @rmtoll CR1 TCIE LL_I2C_IsEnabledIT_TC * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_TC(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_TCIE) == (I2C_CR1_TCIE)) ? 1UL : 0UL); } /** * @brief Enable Error interrupts. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @note Any of these errors will generate interrupt : * Arbitration Loss (ARLO) * Bus Error detection (BERR) * Overrun/Underrun (OVR) * SMBus Timeout detection (TIMEOUT) * SMBus PEC error detection (PECERR) * SMBus Alert pin event detection (ALERT) * @rmtoll CR1 ERRIE LL_I2C_EnableIT_ERR * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableIT_ERR(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR1, I2C_CR1_ERRIE); } /** * @brief Disable Error interrupts. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @note Any of these errors will generate interrupt : * Arbitration Loss (ARLO) * Bus Error detection (BERR) * Overrun/Underrun (OVR) * SMBus Timeout detection (TIMEOUT) * SMBus PEC error detection (PECERR) * SMBus Alert pin event detection (ALERT) * @rmtoll CR1 ERRIE LL_I2C_DisableIT_ERR * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableIT_ERR(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR1, I2C_CR1_ERRIE); } /** * @brief Check if Error interrupts are enabled or disabled. * @rmtoll CR1 ERRIE LL_I2C_IsEnabledIT_ERR * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledIT_ERR(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR1, I2C_CR1_ERRIE) == (I2C_CR1_ERRIE)) ? 1UL : 0UL); } /** * @} */ /** @defgroup I2C_LL_EF_FLAG_management FLAG_management * @{ */ /** * @brief Indicate the status of Transmit data register empty flag. * @note RESET: When next data is written in Transmit data register. * SET: When Transmit data register is empty. * @rmtoll ISR TXE LL_I2C_IsActiveFlag_TXE * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_TXE(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_TXE) == (I2C_ISR_TXE)) ? 1UL : 0UL); } /** * @brief Indicate the status of Transmit interrupt flag. * @note RESET: When next data is written in Transmit data register. * SET: When Transmit data register is empty. * @rmtoll ISR TXIS LL_I2C_IsActiveFlag_TXIS * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_TXIS(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_TXIS) == (I2C_ISR_TXIS)) ? 1UL : 0UL); } /** * @brief Indicate the status of Receive data register not empty flag. * @note RESET: When Receive data register is read. * SET: When the received data is copied in Receive data register. * @rmtoll ISR RXNE LL_I2C_IsActiveFlag_RXNE * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_RXNE(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_RXNE) == (I2C_ISR_RXNE)) ? 1UL : 0UL); } /** * @brief Indicate the status of Address matched flag (slave mode). * @note RESET: Clear default value. * SET: When the received slave address matched with one of the enabled slave address. * @rmtoll ISR ADDR LL_I2C_IsActiveFlag_ADDR * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_ADDR(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_ADDR) == (I2C_ISR_ADDR)) ? 1UL : 0UL); } /** * @brief Indicate the status of Not Acknowledge received flag. * @note RESET: Clear default value. * SET: When a NACK is received after a byte transmission. * @rmtoll ISR NACKF LL_I2C_IsActiveFlag_NACK * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_NACK(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_NACKF) == (I2C_ISR_NACKF)) ? 1UL : 0UL); } /** * @brief Indicate the status of Stop detection flag. * @note RESET: Clear default value. * SET: When a Stop condition is detected. * @rmtoll ISR STOPF LL_I2C_IsActiveFlag_STOP * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_STOP(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_STOPF) == (I2C_ISR_STOPF)) ? 1UL : 0UL); } /** * @brief Indicate the status of Transfer complete flag (master mode). * @note RESET: Clear default value. * SET: When RELOAD=0, AUTOEND=0 and NBYTES date have been transferred. * @rmtoll ISR TC LL_I2C_IsActiveFlag_TC * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_TC(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_TC) == (I2C_ISR_TC)) ? 1UL : 0UL); } /** * @brief Indicate the status of Transfer complete flag (master mode). * @note RESET: Clear default value. * SET: When RELOAD=1 and NBYTES date have been transferred. * @rmtoll ISR TCR LL_I2C_IsActiveFlag_TCR * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_TCR(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_TCR) == (I2C_ISR_TCR)) ? 1UL : 0UL); } /** * @brief Indicate the status of Bus error flag. * @note RESET: Clear default value. * SET: When a misplaced Start or Stop condition is detected. * @rmtoll ISR BERR LL_I2C_IsActiveFlag_BERR * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_BERR(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_BERR) == (I2C_ISR_BERR)) ? 1UL : 0UL); } /** * @brief Indicate the status of Arbitration lost flag. * @note RESET: Clear default value. * SET: When arbitration lost. * @rmtoll ISR ARLO LL_I2C_IsActiveFlag_ARLO * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_ARLO(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_ARLO) == (I2C_ISR_ARLO)) ? 1UL : 0UL); } /** * @brief Indicate the status of Overrun/Underrun flag (slave mode). * @note RESET: Clear default value. * SET: When an overrun/underrun error occurs (Clock Stretching Disabled). * @rmtoll ISR OVR LL_I2C_IsActiveFlag_OVR * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_OVR(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_OVR) == (I2C_ISR_OVR)) ? 1UL : 0UL); } /** * @brief Indicate the status of SMBus PEC error flag in reception. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @note RESET: Clear default value. * SET: When the received PEC does not match with the PEC register content. * @rmtoll ISR PECERR LL_I2C_IsActiveSMBusFlag_PECERR * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_PECERR(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_PECERR) == (I2C_ISR_PECERR)) ? 1UL : 0UL); } /** * @brief Indicate the status of SMBus Timeout detection flag. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @note RESET: Clear default value. * SET: When a timeout or extended clock timeout occurs. * @rmtoll ISR TIMEOUT LL_I2C_IsActiveSMBusFlag_TIMEOUT * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_TIMEOUT(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_TIMEOUT) == (I2C_ISR_TIMEOUT)) ? 1UL : 0UL); } /** * @brief Indicate the status of SMBus alert flag. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @note RESET: Clear default value. * SET: When SMBus host configuration, SMBus alert enabled and * a falling edge event occurs on SMBA pin. * @rmtoll ISR ALERT LL_I2C_IsActiveSMBusFlag_ALERT * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveSMBusFlag_ALERT(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_ALERT) == (I2C_ISR_ALERT)) ? 1UL : 0UL); } /** * @brief Indicate the status of Bus Busy flag. * @note RESET: Clear default value. * SET: When a Start condition is detected. * @rmtoll ISR BUSY LL_I2C_IsActiveFlag_BUSY * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsActiveFlag_BUSY(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->ISR, I2C_ISR_BUSY) == (I2C_ISR_BUSY)) ? 1UL : 0UL); } /** * @brief Clear Address Matched flag. * @rmtoll ICR ADDRCF LL_I2C_ClearFlag_ADDR * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_ClearFlag_ADDR(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->ICR, I2C_ICR_ADDRCF); } /** * @brief Clear Not Acknowledge flag. * @rmtoll ICR NACKCF LL_I2C_ClearFlag_NACK * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_ClearFlag_NACK(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->ICR, I2C_ICR_NACKCF); } /** * @brief Clear Stop detection flag. * @rmtoll ICR STOPCF LL_I2C_ClearFlag_STOP * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_ClearFlag_STOP(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->ICR, I2C_ICR_STOPCF); } /** * @brief Clear Transmit data register empty flag (TXE). * @note This bit can be clear by software in order to flush the transmit data register (TXDR). * @rmtoll ISR TXE LL_I2C_ClearFlag_TXE * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_ClearFlag_TXE(I2C_TypeDef *I2Cx) { WRITE_REG(I2Cx->ISR, I2C_ISR_TXE); } /** * @brief Clear Bus error flag. * @rmtoll ICR BERRCF LL_I2C_ClearFlag_BERR * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_ClearFlag_BERR(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->ICR, I2C_ICR_BERRCF); } /** * @brief Clear Arbitration lost flag. * @rmtoll ICR ARLOCF LL_I2C_ClearFlag_ARLO * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_ClearFlag_ARLO(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->ICR, I2C_ICR_ARLOCF); } /** * @brief Clear Overrun/Underrun flag. * @rmtoll ICR OVRCF LL_I2C_ClearFlag_OVR * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_ClearFlag_OVR(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->ICR, I2C_ICR_OVRCF); } /** * @brief Clear SMBus PEC error flag. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll ICR PECCF LL_I2C_ClearSMBusFlag_PECERR * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_ClearSMBusFlag_PECERR(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->ICR, I2C_ICR_PECCF); } /** * @brief Clear SMBus Timeout detection flag. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll ICR TIMOUTCF LL_I2C_ClearSMBusFlag_TIMEOUT * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_ClearSMBusFlag_TIMEOUT(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->ICR, I2C_ICR_TIMOUTCF); } /** * @brief Clear SMBus Alert flag. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll ICR ALERTCF LL_I2C_ClearSMBusFlag_ALERT * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_ClearSMBusFlag_ALERT(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->ICR, I2C_ICR_ALERTCF); } /** * @} */ /** @defgroup I2C_LL_EF_Data_Management Data_Management * @{ */ /** * @brief Enable automatic STOP condition generation (master mode). * @note Automatic end mode : a STOP condition is automatically sent when NBYTES data are transferred. * This bit has no effect in slave mode or when RELOAD bit is set. * @rmtoll CR2 AUTOEND LL_I2C_EnableAutoEndMode * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableAutoEndMode(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR2, I2C_CR2_AUTOEND); } /** * @brief Disable automatic STOP condition generation (master mode). * @note Software end mode : TC flag is set when NBYTES data are transferre, stretching SCL low. * @rmtoll CR2 AUTOEND LL_I2C_DisableAutoEndMode * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableAutoEndMode(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR2, I2C_CR2_AUTOEND); } /** * @brief Check if automatic STOP condition is enabled or disabled. * @rmtoll CR2 AUTOEND LL_I2C_IsEnabledAutoEndMode * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledAutoEndMode(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR2, I2C_CR2_AUTOEND) == (I2C_CR2_AUTOEND)) ? 1UL : 0UL); } /** * @brief Enable reload mode (master mode). * @note The transfer is not completed after the NBYTES data transfer, NBYTES will be reloaded when TCR flag is set. * @rmtoll CR2 RELOAD LL_I2C_EnableReloadMode * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableReloadMode(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR2, I2C_CR2_RELOAD); } /** * @brief Disable reload mode (master mode). * @note The transfer is completed after the NBYTES data transfer(STOP or RESTART will follow). * @rmtoll CR2 RELOAD LL_I2C_DisableReloadMode * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableReloadMode(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR2, I2C_CR2_RELOAD); } /** * @brief Check if reload mode is enabled or disabled. * @rmtoll CR2 RELOAD LL_I2C_IsEnabledReloadMode * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledReloadMode(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR2, I2C_CR2_RELOAD) == (I2C_CR2_RELOAD)) ? 1UL : 0UL); } /** * @brief Configure the number of bytes for transfer. * @note Changing these bits when START bit is set is not allowed. * @rmtoll CR2 NBYTES LL_I2C_SetTransferSize * @param I2Cx I2C Instance. * @param TransferSize This parameter must be a value between Min_Data=0x00 and Max_Data=0xFF. * @retval None */ __STATIC_INLINE void LL_I2C_SetTransferSize(I2C_TypeDef *I2Cx, uint32_t TransferSize) { MODIFY_REG(I2Cx->CR2, I2C_CR2_NBYTES, TransferSize << I2C_CR2_NBYTES_Pos); } /** * @brief Get the number of bytes configured for transfer. * @rmtoll CR2 NBYTES LL_I2C_GetTransferSize * @param I2Cx I2C Instance. * @retval Value between Min_Data=0x0 and Max_Data=0xFF */ __STATIC_INLINE uint32_t LL_I2C_GetTransferSize(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->CR2, I2C_CR2_NBYTES) >> I2C_CR2_NBYTES_Pos); } /** * @brief Prepare the generation of a ACKnowledge or Non ACKnowledge condition after the address receive match code or next received byte. * @note Usage in Slave mode only. * @rmtoll CR2 NACK LL_I2C_AcknowledgeNextData * @param I2Cx I2C Instance. * @param TypeAcknowledge This parameter can be one of the following values: * @arg @ref LL_I2C_ACK * @arg @ref LL_I2C_NACK * @retval None */ __STATIC_INLINE void LL_I2C_AcknowledgeNextData(I2C_TypeDef *I2Cx, uint32_t TypeAcknowledge) { MODIFY_REG(I2Cx->CR2, I2C_CR2_NACK, TypeAcknowledge); } /** * @brief Generate a START or RESTART condition * @note The START bit can be set even if bus is BUSY or I2C is in slave mode. * This action has no effect when RELOAD is set. * @rmtoll CR2 START LL_I2C_GenerateStartCondition * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_GenerateStartCondition(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR2, I2C_CR2_START); } /** * @brief Generate a STOP condition after the current byte transfer (master mode). * @rmtoll CR2 STOP LL_I2C_GenerateStopCondition * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_GenerateStopCondition(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR2, I2C_CR2_STOP); } /** * @brief Enable automatic RESTART Read request condition for 10bit address header (master mode). * @note The master sends the complete 10bit slave address read sequence : * Start + 2 bytes 10bit address in Write direction + Restart + first 7 bits of 10bit address in Read direction. * @rmtoll CR2 HEAD10R LL_I2C_EnableAuto10BitRead * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableAuto10BitRead(I2C_TypeDef *I2Cx) { CLEAR_BIT(I2Cx->CR2, I2C_CR2_HEAD10R); } /** * @brief Disable automatic RESTART Read request condition for 10bit address header (master mode). * @note The master only sends the first 7 bits of 10bit address in Read direction. * @rmtoll CR2 HEAD10R LL_I2C_DisableAuto10BitRead * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_DisableAuto10BitRead(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR2, I2C_CR2_HEAD10R); } /** * @brief Check if automatic RESTART Read request condition for 10bit address header is enabled or disabled. * @rmtoll CR2 HEAD10R LL_I2C_IsEnabledAuto10BitRead * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledAuto10BitRead(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR2, I2C_CR2_HEAD10R) != (I2C_CR2_HEAD10R)) ? 1UL : 0UL); } /** * @brief Configure the transfer direction (master mode). * @note Changing these bits when START bit is set is not allowed. * @rmtoll CR2 RD_WRN LL_I2C_SetTransferRequest * @param I2Cx I2C Instance. * @param TransferRequest This parameter can be one of the following values: * @arg @ref LL_I2C_REQUEST_WRITE * @arg @ref LL_I2C_REQUEST_READ * @retval None */ __STATIC_INLINE void LL_I2C_SetTransferRequest(I2C_TypeDef *I2Cx, uint32_t TransferRequest) { MODIFY_REG(I2Cx->CR2, I2C_CR2_RD_WRN, TransferRequest); } /** * @brief Get the transfer direction requested (master mode). * @rmtoll CR2 RD_WRN LL_I2C_GetTransferRequest * @param I2Cx I2C Instance. * @retval Returned value can be one of the following values: * @arg @ref LL_I2C_REQUEST_WRITE * @arg @ref LL_I2C_REQUEST_READ */ __STATIC_INLINE uint32_t LL_I2C_GetTransferRequest(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->CR2, I2C_CR2_RD_WRN)); } /** * @brief Configure the slave address for transfer (master mode). * @note Changing these bits when START bit is set is not allowed. * @rmtoll CR2 SADD LL_I2C_SetSlaveAddr * @param I2Cx I2C Instance. * @param SlaveAddr This parameter must be a value between Min_Data=0x00 and Max_Data=0x3F. * @retval None */ __STATIC_INLINE void LL_I2C_SetSlaveAddr(I2C_TypeDef *I2Cx, uint32_t SlaveAddr) { MODIFY_REG(I2Cx->CR2, I2C_CR2_SADD, SlaveAddr); } /** * @brief Get the slave address programmed for transfer. * @rmtoll CR2 SADD LL_I2C_GetSlaveAddr * @param I2Cx I2C Instance. * @retval Value between Min_Data=0x0 and Max_Data=0x3F */ __STATIC_INLINE uint32_t LL_I2C_GetSlaveAddr(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->CR2, I2C_CR2_SADD)); } /** * @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). * @rmtoll CR2 SADD LL_I2C_HandleTransfer\n * CR2 ADD10 LL_I2C_HandleTransfer\n * CR2 RD_WRN LL_I2C_HandleTransfer\n * CR2 START LL_I2C_HandleTransfer\n * CR2 STOP LL_I2C_HandleTransfer\n * CR2 RELOAD LL_I2C_HandleTransfer\n * CR2 NBYTES LL_I2C_HandleTransfer\n * CR2 AUTOEND LL_I2C_HandleTransfer\n * CR2 HEAD10R LL_I2C_HandleTransfer * @param I2Cx I2C Instance. * @param SlaveAddr Specifies the slave address to be programmed. * @param SlaveAddrSize This parameter can be one of the following values: * @arg @ref LL_I2C_ADDRSLAVE_7BIT * @arg @ref LL_I2C_ADDRSLAVE_10BIT * @param TransferSize Specifies the number of bytes to be programmed. * This parameter must be a value between Min_Data=0 and Max_Data=255. * @param EndMode This parameter can be one of the following values: * @arg @ref LL_I2C_MODE_RELOAD * @arg @ref LL_I2C_MODE_AUTOEND * @arg @ref LL_I2C_MODE_SOFTEND * @arg @ref LL_I2C_MODE_SMBUS_RELOAD * @arg @ref LL_I2C_MODE_SMBUS_AUTOEND_NO_PEC * @arg @ref LL_I2C_MODE_SMBUS_SOFTEND_NO_PEC * @arg @ref LL_I2C_MODE_SMBUS_AUTOEND_WITH_PEC * @arg @ref LL_I2C_MODE_SMBUS_SOFTEND_WITH_PEC * @param Request This parameter can be one of the following values: * @arg @ref LL_I2C_GENERATE_NOSTARTSTOP * @arg @ref LL_I2C_GENERATE_STOP * @arg @ref LL_I2C_GENERATE_START_READ * @arg @ref LL_I2C_GENERATE_START_WRITE * @arg @ref LL_I2C_GENERATE_RESTART_7BIT_READ * @arg @ref LL_I2C_GENERATE_RESTART_7BIT_WRITE * @arg @ref LL_I2C_GENERATE_RESTART_10BIT_READ * @arg @ref LL_I2C_GENERATE_RESTART_10BIT_WRITE * @retval None */ __STATIC_INLINE void LL_I2C_HandleTransfer(I2C_TypeDef *I2Cx, uint32_t SlaveAddr, uint32_t SlaveAddrSize, uint32_t TransferSize, uint32_t EndMode, uint32_t Request) { MODIFY_REG(I2Cx->CR2, I2C_CR2_SADD | I2C_CR2_ADD10 | (I2C_CR2_RD_WRN & (uint32_t)(Request >> (31U - I2C_CR2_RD_WRN_Pos))) | I2C_CR2_START | I2C_CR2_STOP | I2C_CR2_RELOAD | I2C_CR2_NBYTES | I2C_CR2_AUTOEND | I2C_CR2_HEAD10R, SlaveAddr | SlaveAddrSize | (TransferSize << I2C_CR2_NBYTES_Pos) | EndMode | Request); } /** * @brief Indicate the value of transfer direction (slave mode). * @note RESET: Write transfer, Slave enters in receiver mode. * SET: Read transfer, Slave enters in transmitter mode. * @rmtoll ISR DIR LL_I2C_GetTransferDirection * @param I2Cx I2C Instance. * @retval Returned value can be one of the following values: * @arg @ref LL_I2C_DIRECTION_WRITE * @arg @ref LL_I2C_DIRECTION_READ */ __STATIC_INLINE uint32_t LL_I2C_GetTransferDirection(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->ISR, I2C_ISR_DIR)); } /** * @brief Return the slave matched address. * @rmtoll ISR ADDCODE LL_I2C_GetAddressMatchCode * @param I2Cx I2C Instance. * @retval Value between Min_Data=0x00 and Max_Data=0x3F */ __STATIC_INLINE uint32_t LL_I2C_GetAddressMatchCode(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->ISR, I2C_ISR_ADDCODE) >> I2C_ISR_ADDCODE_Pos << 1); } /** * @brief Enable internal comparison of the SMBus Packet Error byte (transmission or reception mode). * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @note This feature is cleared by hardware when the PEC byte is transferred, or when a STOP condition or an Address Matched is received. * This bit has no effect when RELOAD bit is set. * This bit has no effect in device mode when SBC bit is not set. * @rmtoll CR2 PECBYTE LL_I2C_EnableSMBusPECCompare * @param I2Cx I2C Instance. * @retval None */ __STATIC_INLINE void LL_I2C_EnableSMBusPECCompare(I2C_TypeDef *I2Cx) { SET_BIT(I2Cx->CR2, I2C_CR2_PECBYTE); } /** * @brief Check if the SMBus Packet Error byte internal comparison is requested or not. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll CR2 PECBYTE LL_I2C_IsEnabledSMBusPECCompare * @param I2Cx I2C Instance. * @retval State of bit (1 or 0). */ __STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusPECCompare(const I2C_TypeDef *I2Cx) { return ((READ_BIT(I2Cx->CR2, I2C_CR2_PECBYTE) == (I2C_CR2_PECBYTE)) ? 1UL : 0UL); } /** * @brief Get the SMBus Packet Error byte calculated. * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not * SMBus feature is supported by the I2Cx Instance. * @rmtoll PECR PEC LL_I2C_GetSMBusPEC * @param I2Cx I2C Instance. * @retval Value between Min_Data=0x00 and Max_Data=0xFF */ __STATIC_INLINE uint32_t LL_I2C_GetSMBusPEC(const I2C_TypeDef *I2Cx) { return (uint32_t)(READ_BIT(I2Cx->PECR, I2C_PECR_PEC)); } /** * @brief Read Receive Data register. * @rmtoll RXDR RXDATA LL_I2C_ReceiveData8 * @param I2Cx I2C Instance. * @retval Value between Min_Data=0x00 and Max_Data=0xFF */ __STATIC_INLINE uint8_t LL_I2C_ReceiveData8(const I2C_TypeDef *I2Cx) { return (uint8_t)(READ_BIT(I2Cx->RXDR, I2C_RXDR_RXDATA)); } /** * @brief Write in Transmit Data Register . * @rmtoll TXDR TXDATA LL_I2C_TransmitData8 * @param I2Cx I2C Instance. * @param Data Value between Min_Data=0x00 and Max_Data=0xFF * @retval None */ __STATIC_INLINE void LL_I2C_TransmitData8(I2C_TypeDef *I2Cx, uint8_t Data) { WRITE_REG(I2Cx->TXDR, Data); } /** * @} */ #if defined(USE_FULL_LL_DRIVER) /** @defgroup I2C_LL_EF_Init Initialization and de-initialization functions * @{ */ ErrorStatus LL_I2C_Init(I2C_TypeDef *I2Cx, const LL_I2C_InitTypeDef *I2C_InitStruct); ErrorStatus LL_I2C_DeInit(const I2C_TypeDef *I2Cx); void LL_I2C_StructInit(LL_I2C_InitTypeDef *I2C_InitStruct); /** * @} */ #endif /* USE_FULL_LL_DRIVER */ /** * @} */ /** * @} */ #endif /* I2C1 || I2C2 */ /** * @} */ #ifdef __cplusplus } #endif #endif /* STM32F0xx_LL_I2C_H */