/* * Copyright 2020-2021 NXP * All rights reserved. * * SPDX-License-Identifier: BSD-3-Clause */ #include "fsl_mipi_dsi.h" /******************************************************************************* * Definitions ******************************************************************************/ /* Component ID definition, used by tools. */ #ifndef FSL_COMPONENT_ID #define FSL_COMPONENT_ID "platform.drivers.mipi_dsi_split" #endif /* The timeout cycles to wait for DSI state machine idle. */ #ifndef FSL_MIPI_DSI_IDLE_TIMEOUT #define FSL_MIPI_DSI_IDLE_TIMEOUT 0x1000U #endif /* PLL CN should be in the range of 1 to 32. */ #define DSI_DPHY_PLL_CN_MIN 1U #define DSI_DPHY_PLL_CN_MAX 32U /* PLL refClk / CN should be in the range of 24M to 30M. */ #define DSI_DPHY_PLL_REFCLK_CN_MIN 24000000U #define DSI_DPHY_PLL_REFCLK_CN_MAX 30000000U /* PLL CM should be in the range of 16 to 255. */ #define DSI_DPHY_PLL_CM_MIN 16U #define DSI_DPHY_PLL_CM_MAX 255U /* PLL VCO output frequency max value is 1.5GHz, VCO output is (refClk / CN ) * CM. */ #define DSI_DPHY_PLL_VCO_MAX 1500000000U #define DSI_DPHY_PLL_VCO_MIN (DSI_DPHY_PLL_REFCLK_CN_MIN * DSI_DPHY_PLL_CM_MIN) #define PKT_CONTROL_WORD_COUNT(wc) ((uint32_t)(wc) << 0U) #define PKT_CONTROL_VC(vc) ((uint32_t)(vc) << 16U) #define PKT_CONTROL_HEADER_TYPE(type) ((uint32_t)(type) << 18U) #define PKT_CONTROL_HS_MASK (1UL << 24U) #define PKT_CONTROL_BTA_MASK (1UL << 25U) #define PKT_CONTROL_BTA_ONLY_MASK (1UL << 26U) /* Macro used for D-PHY timing setting. */ #define DSI_THS_ZERO_BYTE_CLK_BASE 6U #define DSI_TCLK_ZERO_BYTE_CLK_BASE 3U #define DSI_THS_PREPARE_HALF_ESC_CLK_BASE 2U #define DSI_TCLK_PREPARE_HALF_ESC_CLK_BASE 2U #define DSI_THS_PREPARE_HALF_ESC_CLK_MIN (DSI_THS_PREPARE_HALF_ESC_CLK_BASE) #define DSI_TCLK_PREPARE_HALF_ESC_CLK_MIN (DSI_TCLK_PREPARE_HALF_ESC_CLK_BASE) #define DSI_THS_PREPARE_HALF_ESC_CLK_MAX (5U) #define DSI_TCLK_PREPARE_HALF_ESC_CLK_MAX (3U) /* Convert ns to byte clock. */ #define DSI_NS_TO_BYTE_CLK(ns, byte_clk_khz) ((ns) * (byte_clk_khz) / 1000000U) /* Convert ns+UI to byte clock. */ #define DSI_NS_UI_TO_BYTE_CLK(ns, UI, byte_clk_khz) ((((ns) * (byte_clk_khz)) + ((UI)*125000U)) / 1000000U) /* Packet overhead for HSA, HFP, HBP */ #define DSI_HSA_OVERHEAD_BYTE 10UL /* HSS + HSA header + HSA CRC. */ #define DSI_HFP_OVERHEAD_BYTE 8UL /* RGB data packet CRC + HFP header + HFP CRC. */ #define DSI_HBP_OVERHEAD_BYTE 14UL /* HSE + HBP header + HBP CRC + RGB data packet header */ #define DSI_INT_STATUS_TRIGGER_MASK \ ((uint32_t)kDSI_InterruptGroup1ResetTriggerReceived | (uint32_t)kDSI_InterruptGroup1TearTriggerReceived | \ (uint32_t)kDSI_InterruptGroup1AckTriggerReceived) #define DSI_INT_STATUS_ERROR_REPORT_MASK (0xFFFFU << 9U) #if (defined(FSL_FEATURE_DSI_CSR_OFFSET) && FSL_FEATURE_DSI_CSR_OFFSET) #if (defined(FSL_FEATURE_LDB_COMBO_PHY) && FSL_FEATURE_LDB_COMBO_PHY) typedef MIPI_DSI_LVDS_COMBO_CSR_Type MIPI_DSI_CSR_Type; #define MIPI_DSI_CSR_ULPS_CTRL(csr) ((csr)->ULPS_CTRL) #define MIPI_DSI_CSR_ULPS_CTRL_ULPS_MASK MIPI_DSI_LVDS_COMBO_CSR_ULPS_CTRL_TX_ULPS_MASK #define MIPI_DSI_CSR_PXL2DPI(csr) ((csr)->PXL2DPI_CTRL) #else #define MIPI_DSI_CSR_ULPS_CTRL(csr) ((csr)->TX_ULPS_ENABLE) #define MIPI_DSI_CSR_ULPS_CTRL_ULPS_MASK MIPI_DSI_TX_ULPS_ENABLE_TX_ULPS_ENABLE_MASK #define MIPI_DSI_CSR_PXL2DPI(csr) ((csr)->PXL2DPI_CONFIG) #endif #define DSI_GET_CSR(dsi_base) (MIPI_DSI_CSR_Type *)((uint32_t)(dsi_base) - (uint32_t)FSL_FEATURE_DSI_CSR_OFFSET) #endif /*! @brief Typedef for MIPI DSI interrupt handler. */ typedef void (*dsi_isr_t)(const MIPI_DSI_Type *base, dsi_handle_t *handle); /******************************************************************************* * Variables ******************************************************************************/ #if defined(DSI_HOST_IRQS) /* Array of DSI IRQ number. */ static const DSI_HOST_IRQn s_dsiIRQ[] = DSI_HOST_IRQS; #endif /*! @brief Pointers to MIPI DSI bases for each instance. */ static DSI_HOST_Type *const s_dsiBases[] = DSI_HOST_BASE_PTRS; /*! @brief MIPI DSI internal handle pointer array */ static dsi_handle_t *s_dsiHandle[ARRAY_SIZE(s_dsiBases)]; /*! @brief Pointer to IRQ handler. */ static dsi_isr_t s_dsiIsr; #if !(defined(FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) && FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) /*! @brief Pointers to MIPI DSI clocks for each instance. */ static const clock_ip_name_t s_dsiClocks[] = MIPI_DSI_HOST_CLOCKS; #endif /* FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL */ /******************************************************************************* * Prototypes ******************************************************************************/ /*! * @brief Get the MIPI DSI host controller instance from peripheral base address. * * @param base MIPI DSI peripheral base address. * @return MIPI DSI instance. */ uint32_t DSI_GetInstance(const MIPI_DSI_Type *base); #if !((defined(FSL_FEATURE_MIPI_NO_DPHY_PLL) && (FSL_FEATURE_MIPI_DSI_HOST_NO_DPHY_PLL))) /*! * @brief Convert the D-PHY PLL CN to the value could be set to register. * * @param cn The CN value. * @return The register value. */ static uint8_t DSI_EncodeDphyPllCn(uint8_t cn); /*! * @brief Convert the D-PHY PLL CM to the value could be set to register. * * @param cm The CM value. * @return The register value. */ static uint8_t DSI_EncodeDphyPllCm(uint8_t cm); /*! * @brief Calculate the D-PHY PLL dividers to generate the desired output frequency. * * Calculate the PLL dividers to generate the most close desired output PLL frequency. * * txHsBitClk_Hz = refClkFreq_Hz * CM / (CN * CO). * CM: 16 ~ 255 * CN: 1 ~ 32 * CO: 1, 2, 4, 8 * * @param cn The CN value, convert using @ref DSI_EncodeDphyPllCn before setting to register. * @param cm The CM value, convert using @ref DSI_EncodeDphyPllCm before setting to register. * @param co The CO value, could set to register directly. * @param refClkFreq_Hz The D-PHY input reference clock frequency (REF_CLK). * @param desiredOutFreq_Hz Desired PLL output frequency. * @return The actually output frequency using the returned dividers. If could not * find suitable dividers, return 0. */ static uint32_t DSI_DphyGetPllDivider( uint32_t *cn, uint32_t *cm, uint32_t *co, uint32_t refClkFreq_Hz, uint32_t desiredOutFreq_Hz); #endif /*! * @brief Clear the RX FIFO. * * @param base MIPI DSI host peripheral base address. */ static void DSI_ApbClearRxFifo(const MIPI_DSI_Type *base); /*! * @brief Handle the DSI transfer result. * * @param base MIPI DSI host peripheral base address. * @param xfer The transfer definition. * @param intFlags1 Interrupt flag group 1. * @param intFlags2 Interrupt flag group 2. * @retval kStatus_Success No error happens. * @retval kStatus_Timeout Hardware timeout detected. * @retval kStatus_DSI_RxDataError RX data error. * @retval kStatus_DSI_ErrorReportReceived Error Report packet received. * @retval kStatus_DSI_Fail Transfer failed for other reasons. */ static status_t DSI_HandleResult(const MIPI_DSI_Type *base, uint32_t intFlags1, uint32_t intFlags2, dsi_transfer_t *xfer); /*! * @brief Prepare for the DSI APB transfer. * * This function fills TX data to DSI TX FIFO and sets the packet control * register. Packet transfer could start using @ref DSI_SendApbPacket after * this function. * * @param base MIPI DSI host peripheral base address. * @param xfer The transfer definition. * @retval kStatus_Success It is ready to start transfer. * @retval kStatus_DSI_NotSupported The transfer format is not supported. */ static status_t DSI_PrepareApbTransfer(const MIPI_DSI_Type *base, dsi_transfer_t *xfer); /******************************************************************************* * Code ******************************************************************************/ uint32_t DSI_GetInstance(const MIPI_DSI_Type *base) { uint32_t instance; /* Find the instance index from base address mappings. */ for (instance = 0; instance < ARRAY_SIZE(s_dsiBases); instance++) { if (s_dsiBases[instance] == base->host) { break; } } assert(instance < ARRAY_SIZE(s_dsiBases)); return instance; } #if !((defined(FSL_FEATURE_MIPI_NO_DPHY_PLL) && (FSL_FEATURE_MIPI_DSI_HOST_NO_DPHY_PLL))) static uint8_t DSI_EncodeDphyPllCn(uint8_t cn) { assert((cn >= 1U) && (cn <= 32U)); if (1U == cn) { return 0x1FU; } else { return (uint8_t)((0x65BD44E0UL >> ((uint32_t)cn - 2U)) & 0x1FU); } } static uint8_t DSI_EncodeDphyPllCm(uint8_t cm) { assert(cm >= 16U); if (cm <= 31U) { return 0xE0U | cm; } else if (cm <= 63U) { return 0xC0U | (cm & 0x1FU); } else if (cm <= 127U) { return 0x80U | (cm & 0x3FU); } else { return cm & 0xCFU; } } static uint32_t DSI_DphyGetPllDivider( uint32_t *cn, uint32_t *cm, uint32_t *co, uint32_t refClkFreq_Hz, uint32_t desiredOutFreq_Hz) { uint32_t cnCur, cmCur, coShiftCur, pllFreqCur, diffCur, vcoFreq, refClk_CN; uint32_t diff = 0xFFFFFFFFU; uint32_t pllFreqCandidate = 0U; /* CO available values are 1, 2, 4, 8, so the shift values are 0, 1, 2, 3. */ for (coShiftCur = 0U; coShiftCur <= 3U; coShiftCur++) { /* Desired VCO output frequency. */ vcoFreq = desiredOutFreq_Hz << coShiftCur; /* If desired VCO output frequency is too small, try larger CO value. */ if (vcoFreq < DSI_DPHY_PLL_VCO_MIN) { continue; } /* If desired VCO output frequency is too large, search finished. */ if (vcoFreq > DSI_DPHY_PLL_VCO_MAX) { break; } /* Now search the best CN and CM to generate disired VCO output frequency. */ for (cnCur = DSI_DPHY_PLL_CN_MIN; cnCur <= DSI_DPHY_PLL_CN_MAX; cnCur++) { /* REF_CLK / CN. */ refClk_CN = refClkFreq_Hz / cnCur; /* If desired REF_CLK / CN frequency is too large, try larger CN value. */ if (refClk_CN > DSI_DPHY_PLL_REFCLK_CN_MAX) { continue; } /* If desired REF_CLK / CN frequency is too small, stop search. */ if (refClk_CN < DSI_DPHY_PLL_REFCLK_CN_MIN) { break; } /* Get the CM most close. */ cmCur = (vcoFreq + (refClk_CN / 2U)) / refClk_CN; /* If calculated value is (DSI_DPHY_PLL_CM_MAX + 1), use DSI_DPHY_PLL_CM_MAX. */ if ((DSI_DPHY_PLL_CM_MAX + 1U) == cmCur) { cmCur = DSI_DPHY_PLL_CM_MAX; } if ((cmCur < DSI_DPHY_PLL_CM_MIN) || (cmCur > DSI_DPHY_PLL_CM_MAX)) { continue; } /* Output frequency using current dividers. */ pllFreqCur = (refClk_CN * cmCur) >> coShiftCur; diffCur = (pllFreqCur > desiredOutFreq_Hz) ? (pllFreqCur - desiredOutFreq_Hz) : (desiredOutFreq_Hz - pllFreqCur); /* If the dividers is better. */ if (diffCur < diff) { diff = diffCur; *cm = cmCur; *cn = cnCur; *co = coShiftCur; pllFreqCandidate = pllFreqCur; /* If the output PLL frequency is exactly the disired value, return directly. */ if (0U == diff) { return pllFreqCandidate; } } } } return pllFreqCandidate; } #endif static void DSI_ApbClearRxFifo(const MIPI_DSI_Type *base) { volatile uint32_t dummy; uint32_t level = base->apb->PKT_FIFO_RD_LEVEL; while (0U != (level--)) { dummy = base->apb->PKT_RX_PAYLOAD; } (void)dummy; } /*! * brief Initializes an MIPI DSI host with the user configuration. * * This function initializes the MIPI DSI host with the configuration, it should * be called first before other MIPI DSI driver functions. * * param base MIPI DSI host peripheral base address. * param config Pointer to a user-defined configuration structure. */ void DSI_Init(const MIPI_DSI_Type *base, const dsi_config_t *config) { assert(config); #if !(defined(FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) && FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) (void)CLOCK_EnableClock(s_dsiClocks[DSI_GetInstance(base)]); #endif /* FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL */ DSI_HOST_Type *host = base->host; #if (defined(FSL_FEATURE_DSI_CSR_OFFSET) && FSL_FEATURE_DSI_CSR_OFFSET) MIPI_DSI_CSR_Type *csr = DSI_GET_CSR(base); if (config->enableTxUlps) { MIPI_DSI_CSR_ULPS_CTRL(csr) = MIPI_DSI_CSR_ULPS_CTRL_ULPS_MASK; } else { MIPI_DSI_CSR_ULPS_CTRL(csr) = 0U; } #endif host->CFG_NUM_LANES = config->numLanes - 1UL; if (config->enableNonContinuousHsClk) { host->CFG_NONCONTINUOUS_CLK = 0x01U; } else { host->CFG_NONCONTINUOUS_CLK = 0x00U; } if (config->autoInsertEoTp) { host->CFG_AUTOINSERT_EOTP = 0x01U; } else { host->CFG_AUTOINSERT_EOTP = 0x00U; } host->CFG_EXTRA_CMDS_AFTER_EOTP = config->numExtraEoTp; host->CFG_HTX_TO_COUNT = config->htxTo_ByteClk; host->CFG_LRX_H_TO_COUNT = config->lrxHostTo_ByteClk; host->CFG_BTA_H_TO_COUNT = config->btaTo_ByteClk; DSI_ApbClearRxFifo(base); /* Disable all interrupts by default, user could enable * the desired interrupts later. */ base->apb->IRQ_MASK = 0xFFFFFFFFU; base->apb->IRQ_MASK2 = 0xFFFFFFFFU; } /*! * brief Deinitializes an MIPI DSI host. * * This function should be called after all bother MIPI DSI driver functions. * * param base MIPI DSI host peripheral base address. */ void DSI_Deinit(const MIPI_DSI_Type *base) { #if !(defined(FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) && FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL) (void)CLOCK_DisableClock(s_dsiClocks[DSI_GetInstance(base)]); #endif /* FSL_SDK_DISABLE_DRIVER_CLOCK_CONTROL */ } /*! * brief Get the default configuration to initialize the MIPI DSI host. * * The default value is: * code config->numLanes = 4; config->enableNonContinuousHsClk = false; config->enableTxUlps = false; config->autoInsertEoTp = true; config->numExtraEoTp = 0; config->htxTo_ByteClk = 0; config->lrxHostTo_ByteClk = 0; config->btaTo_ByteClk = 0; endcode * * param config Pointer to a user-defined configuration structure. */ void DSI_GetDefaultConfig(dsi_config_t *config) { assert(config); /* Initializes the configure structure to zero. */ (void)memset(config, 0, sizeof(*config)); config->numLanes = 4; config->enableNonContinuousHsClk = false; config->enableTxUlps = false; config->autoInsertEoTp = true; config->numExtraEoTp = 0; config->htxTo_ByteClk = 0; config->lrxHostTo_ByteClk = 0; config->btaTo_ByteClk = 0; } /*! * brief Configure the DPI interface core. * * This function sets the DPI interface configuration, it should be used in * video mode. * * param base MIPI DSI host peripheral base address. * param config Pointer to the DPI interface configuration. * param numLanes Lane number, should be same with the setting in ref dsi_dpi_config_t. * param dpiPixelClkFreq_Hz The DPI pixel clock frequency in Hz. * param dsiHsBitClkFreq_Hz The DSI high speed bit clock frequency in Hz. It is * the same with DPHY PLL output. */ void DSI_SetDpiConfig(const MIPI_DSI_Type *base, const dsi_dpi_config_t *config, uint8_t numLanes, uint32_t dpiPixelClkFreq_Hz, uint32_t dsiHsBitClkFreq_Hz) { assert(config); /* coefficient DPI event size to number of DSI bytes. */ uint32_t coff = (numLanes * dsiHsBitClkFreq_Hz) / (dpiPixelClkFreq_Hz * 8U); DSI_HOST_DPI_INTFC_Type *dpi = base->dpi; #if (defined(FSL_FEATURE_DSI_CSR_OFFSET) && FSL_FEATURE_DSI_CSR_OFFSET) MIPI_DSI_CSR_Type *csr = DSI_GET_CSR(base); MIPI_DSI_CSR_PXL2DPI(csr) = (uint32_t)config->dpiColorCoding; #endif dpi->PIXEL_PAYLOAD_SIZE = config->pixelPayloadSize; dpi->INTERFACE_COLOR_CODING = (uint32_t)config->dpiColorCoding; dpi->PIXEL_FORMAT = (uint32_t)config->pixelPacket; dpi->VIDEO_MODE = (uint32_t)config->videoMode; if (kDSI_DpiBllpLowPower == config->bllpMode) { dpi->BLLP_MODE = 0x1U; dpi->USE_NULL_PKT_BLLP = 0x0U; } else if (kDSI_DpiBllpBlanking == config->bllpMode) { dpi->BLLP_MODE = 0x0U; dpi->USE_NULL_PKT_BLLP = 0x0U; } else { dpi->BLLP_MODE = 0x0U; dpi->USE_NULL_PKT_BLLP = 0x1U; } if (0U != (config->polarityFlags & (uint32_t)kDSI_DpiVsyncActiveHigh)) { dpi->VSYNC_POLARITY = 0x01U; } else { dpi->VSYNC_POLARITY = 0x00U; } if (0U != (config->polarityFlags & (uint32_t)kDSI_DpiHsyncActiveHigh)) { dpi->HSYNC_POLARITY = 0x01U; } else { dpi->HSYNC_POLARITY = 0x00U; } if (kDSI_DpiNonBurstWithSyncPulse == config->videoMode) { dpi->HFP = config->hfp - DSI_HFP_OVERHEAD_BYTE; dpi->HBP = config->hbp - DSI_HBP_OVERHEAD_BYTE; dpi->HSA = config->hsw - DSI_HSA_OVERHEAD_BYTE; dpi->PIXEL_FIFO_SEND_LEVEL = 8; } else { dpi->HFP = config->hfp * coff; dpi->HBP = config->hbp * coff; dpi->HSA = config->hsw * coff; dpi->PIXEL_FIFO_SEND_LEVEL = config->pixelPayloadSize; } dpi->VBP = config->vbp; dpi->VFP = config->vfp; dpi->VACTIVE = config->panelHeight - 1UL; /* TODO: Configure VC if it is available. */ } /*! * brief Initializes the D-PHY * * This function configures the D-PHY timing and setups the D-PHY PLL based on * user configuration. The configuration structure could be got by the function * ref DSI_GetDphyDefaultConfig. * * param base MIPI DSI host peripheral base address. * param config Pointer to the D-PHY configuration. * param refClkFreq_Hz The REFCLK frequency in Hz. * return The actual D-PHY PLL output frequency. If could not configure the * PLL to the target frequency, the return value is 0. */ uint32_t DSI_InitDphy(const MIPI_DSI_Type *base, const dsi_dphy_config_t *config, uint32_t refClkFreq_Hz) { assert(config); DSI_HOST_NXP_FDSOI28_DPHY_INTFC_Type *dphy = base->dphy; DSI_HOST_Type *host = base->host; #if !((defined(FSL_FEATURE_MIPI_NO_DPHY_PLL) && (FSL_FEATURE_MIPI_DSI_HOST_NO_DPHY_PLL))) uint32_t cn, cm, co, outputPllFreq; outputPllFreq = DSI_DphyGetPllDivider(&cn, &cm, &co, refClkFreq_Hz, config->txHsBitClk_Hz); /* If could not find dividers for the output PLL frequency. */ if (0U == outputPllFreq) { return 0U; } /* Set the DPHY parameters. */ dphy->CN = (uint32_t)DSI_EncodeDphyPllCn((uint8_t)cn); dphy->CM = (uint32_t)DSI_EncodeDphyPllCm((uint8_t)cm); dphy->CO = co; #endif /* Set the timing parameters. */ dphy->M_PRG_HS_PREPARE = (uint32_t)config->tHsPrepare_HalfEscClk - DSI_THS_PREPARE_HALF_ESC_CLK_BASE; dphy->MC_PRG_HS_PREPARE = (uint32_t)config->tClkPrepare_HalfEscClk - DSI_TCLK_PREPARE_HALF_ESC_CLK_BASE; dphy->M_PRG_HS_ZERO = (uint32_t)config->tHsZero_ByteClk - DSI_THS_ZERO_BYTE_CLK_BASE; dphy->MC_PRG_HS_ZERO = (uint32_t)config->tClkZero_ByteClk - DSI_TCLK_ZERO_BYTE_CLK_BASE; dphy->M_PRG_HS_TRAIL = config->tHsTrail_ByteClk; dphy->MC_PRG_HS_TRAIL = config->tClkTrail_ByteClk; host->CFG_T_PRE = config->tClkPre_ByteClk; host->CFG_T_POST = config->tClkPost_ByteClk; host->CFG_TX_GAP = config->tHsExit_ByteClk; host->CFG_TWAKEUP = config->tWakeup_EscClk; #if defined(MIPI_RTERM_SEL_dphy_rterm_sel_MASK) dphy->RTERM_SEL = MIPI_RTERM_SEL_dphy_rterm_sel_MASK; #endif #if defined(MIPI_TX_RCAL_dphy_tx_rcal_MASK) dphy->TX_RCAL = 1; #endif dphy->RXLPRP = 1; dphy->RXCDRP = 1; /* Auto power down the inactive lanes. */ dphy->AUTO_PD_EN = 0x1U; dphy->TST = 0x25U; #if !((defined(FSL_FEATURE_MIPI_NO_PLL) && (FSL_FEATURE_MIPI_DSI_HOST_NO_PLL))) /* Power up the PLL. */ dphy->PD_PLL = 0U; /* Wait for the PLL lock. */ while (0UL == dphy->LOCK) { } #endif /* Power up the DPHY. */ dphy->PD_TX = 0U; #if !((defined(FSL_FEATURE_MIPI_NO_PLL) && (FSL_FEATURE_MIPI_DSI_HOST_NO_PLL))) return outputPllFreq; #else return config->txHsBitClk_Hz; #endif } /*! * brief Deinitializes the D-PHY * * Power down the D-PHY PLL and shut down D-PHY. * * param base MIPI DSI host peripheral base address. */ void DSI_DeinitDphy(const MIPI_DSI_Type *base) { #if !((defined(FSL_FEATURE_MIPI_NO_DPHY_PLL) && (FSL_FEATURE_MIPI_DSI_HOST_NO_DPHY_PLL))) /* Power down the PLL. */ base->dphy->PD_PLL = 1U; #endif /* Power down the DPHY. */ base->dphy->PD_TX = 1U; } /*! * brief Get the default D-PHY configuration. * * Gets the default D-PHY configuration, the timing parameters are set according * to D-PHY specification. User could use the configuration directly, or change * some parameters according to the special device. * * param config Pointer to the D-PHY configuration. * param txHsBitClk_Hz High speed bit clock in Hz. * param txEscClk_Hz Esc clock in Hz. */ void DSI_GetDphyDefaultConfig(dsi_dphy_config_t *config, uint32_t txHsBitClk_Hz, uint32_t txEscClk_Hz) { assert(config); /* Initializes the configure structure to zero. */ (void)memset(config, 0, sizeof(*config)); uint32_t byteClkFreq_kHz = txHsBitClk_Hz / 8U / 1000U; uint32_t txEscClk_kHz = txEscClk_Hz / 1000U; config->txHsBitClk_Hz = txHsBitClk_Hz; /* THS-EXIT in byte clock. At least 100ns. */ config->tHsExit_ByteClk = (uint8_t)(DSI_NS_TO_BYTE_CLK(100U, byteClkFreq_kHz) + 1U); /* T-WAKEUP. At least 1ms. */ config->tWakeup_EscClk = txEscClk_Hz / 1000U + 1U; /* THS-PREPARE. 40ns+4*UI to 85ns+6*UI. */ config->tHsPrepare_HalfEscClk = (uint8_t)((40U * txEscClk_kHz * 2U) / 1000000U + (4U * txEscClk_Hz * 2U / txHsBitClk_Hz) + 1U); if (config->tHsPrepare_HalfEscClk < DSI_THS_PREPARE_HALF_ESC_CLK_MIN) { config->tHsPrepare_HalfEscClk = DSI_THS_PREPARE_HALF_ESC_CLK_MIN; } else if (config->tHsPrepare_HalfEscClk > DSI_THS_PREPARE_HALF_ESC_CLK_MAX) { config->tHsPrepare_HalfEscClk = DSI_THS_PREPARE_HALF_ESC_CLK_MAX; } else { /* For MISRA check. */ } /* TCLK-PREPARE. 38ns to 95ns. */ config->tClkPrepare_HalfEscClk = (uint8_t)((38U * txEscClk_kHz * 2U) / 1000000U + 1U); if (config->tClkPrepare_HalfEscClk < DSI_TCLK_PREPARE_HALF_ESC_CLK_MIN) { config->tClkPrepare_HalfEscClk = DSI_TCLK_PREPARE_HALF_ESC_CLK_MIN; } else if (config->tClkPrepare_HalfEscClk > DSI_TCLK_PREPARE_HALF_ESC_CLK_MAX) { config->tClkPrepare_HalfEscClk = DSI_TCLK_PREPARE_HALF_ESC_CLK_MAX; } else { /* For MISRA check. */ } /* THS-ZERO, At least 105ns+6*UI. */ config->tHsZero_ByteClk = (uint8_t)(DSI_NS_UI_TO_BYTE_CLK(105U, 6U, byteClkFreq_kHz) + 1U); if (config->tHsZero_ByteClk < DSI_THS_ZERO_BYTE_CLK_BASE) { config->tHsZero_ByteClk = DSI_THS_ZERO_BYTE_CLK_BASE; } /* TCLK-ZERO, At least 262ns. */ config->tClkZero_ByteClk = (uint8_t)(DSI_NS_TO_BYTE_CLK(262U, byteClkFreq_kHz) + 1U); if (config->tClkZero_ByteClk < DSI_TCLK_ZERO_BYTE_CLK_BASE) { config->tClkZero_ByteClk = DSI_TCLK_ZERO_BYTE_CLK_BASE; } /* THS-TRAIL, 60ns+4*UI to 105ns+12UI. */ /* Due to IP design, extra 4*UI should be added. */ config->tHsTrail_ByteClk = (uint8_t)(DSI_NS_UI_TO_BYTE_CLK(60U, 8U, byteClkFreq_kHz) + 1U); /* TCLK-TRAIL, at least 60ns. */ /* Due to IP design, extra 4*UI should be added. */ config->tClkTrail_ByteClk = (uint8_t)(DSI_NS_UI_TO_BYTE_CLK(60U, 4U, byteClkFreq_kHz) + 1U); /* * T_LPX + T_CLK-PREPARE + T_CLK-ZERO + T_CLK-PRE * T_LPX >= 50ns * T_CLK-PREPARE >= 38ns * T_CLK-ZERO >= 262ns * T_CLK-PRE >= 8*UI */ config->tClkPre_ByteClk = (uint8_t)(DSI_NS_UI_TO_BYTE_CLK(88U, 8U, byteClkFreq_kHz) + 1U) + config->tClkZero_ByteClk; /* * T_CLK-POST + T_CLK-TRAIL * T_CLK-POST >= 60ns + 52*UI. * T_CLK-TRAIL >= 60ns */ config->tClkPost_ByteClk = (uint8_t)(DSI_NS_UI_TO_BYTE_CLK(60U, 52U, byteClkFreq_kHz) + 1U) + config->tClkTrail_ByteClk; } /*! * brief Configure the APB packet to send. * * This function configures the next APB packet transfer. After configuration, * the packet transfer could be started with function ref DSI_SendApbPacket. * If the packet is long packet, Use ref DSI_WriteApbTxPayload to fill the payload * before start transfer. * * param base MIPI DSI host peripheral base address. * param wordCount For long packet, this is the byte count of the payload. * For short packet, this is (data1 << 8) | data0. * param virtualChannel Virtual channel. * param dataType The packet data type, (DI). * param flags The transfer control flags, see ref _dsi_transfer_flags. */ void DSI_SetApbPacketControl( const MIPI_DSI_Type *base, uint16_t wordCount, uint8_t virtualChannel, dsi_tx_data_type_t dataType, uint8_t flags) { uint32_t pktCtrl = PKT_CONTROL_WORD_COUNT(wordCount) | PKT_CONTROL_HEADER_TYPE(dataType); #if defined(DSI_HOST_PKT_CONTROL_VC) pktCtrl |= DSI_HOST_PKT_CONTROL_VC(virtualChannel); #endif if (0U != (flags & (uint8_t)kDSI_TransferUseHighSpeed)) { pktCtrl |= PKT_CONTROL_HS_MASK; } if (0U != (flags & (uint8_t)kDSI_TransferPerformBTA)) { pktCtrl |= PKT_CONTROL_BTA_MASK; } base->apb->PKT_CONTROL = pktCtrl; } /*! * brief Fill the long APB packet payload. * * Write the long packet payload to TX FIFO. * * param base MIPI DSI host peripheral base address. * param payload Pointer to the payload. * param payloadSize Payload size in byte. */ void DSI_WriteApbTxPayload(const MIPI_DSI_Type *base, const uint8_t *payload, uint16_t payloadSize) { DSI_WriteApbTxPayloadExt(base, payload, payloadSize, false, 0U); } void DSI_WriteApbTxPayloadExt( const MIPI_DSI_Type *base, const uint8_t *payload, uint16_t payloadSize, bool sendDscCmd, uint8_t dscCmd) { uint32_t firstWord; uint16_t i; DSI_HOST_APB_PKT_IF_Type *apb = base->apb; payloadSize = sendDscCmd ? payloadSize + 1U : payloadSize; assert(payloadSize <= FSL_DSI_TX_MAX_PAYLOAD_BYTE); /* The first 4-byte. */ if (sendDscCmd) { firstWord = dscCmd; } else { firstWord = *payload; payload++; } payloadSize--; for (i = 1U; i < 4U; i++) { if (payloadSize > 0U) { firstWord |= ((uint32_t)(*payload) << (i << 3U)); payload++; payloadSize--; } else { break; } } apb->TX_PAYLOAD = firstWord; /* Write the payload to the FIFO. */ for (i = 0; i < payloadSize / 4U; i++) { apb->TX_PAYLOAD = *(const uint32_t *)(const void *)payload; payload += 4U; } /* Write the remaining data. */ switch (payloadSize & 0x03U) { case 3: apb->TX_PAYLOAD = ((uint32_t)payload[2] << 16U) | ((uint32_t)payload[1] << 8U) | payload[0]; break; case 2: apb->TX_PAYLOAD = ((uint32_t)payload[1] << 8U) | payload[0]; break; case 1: apb->TX_PAYLOAD = payload[0]; break; default: /* For MISRA 2012 16.4 */ break; } } static status_t DSI_PrepareApbTransfer(const MIPI_DSI_Type *base, dsi_transfer_t *xfer) { /* The receive data size should be smaller than the RX FIRO. */ assert(xfer->rxDataSize <= FSL_DSI_RX_MAX_PAYLOAD_BYTE); assert(xfer->txDataSize <= FSL_DSI_TX_MAX_PAYLOAD_BYTE); uint8_t txDataIndex; uint16_t wordCount; uint32_t intFlags1, intFlags2; uint32_t txDataSize; if (xfer->rxDataSize > 2U) { return kStatus_DSI_NotSupported; } if (xfer->rxDataSize != 0U) { xfer->flags |= (uint8_t)kDSI_TransferPerformBTA; } /* ========================== Prepare TX. ========================== */ /* If xfer->sendDscCmd is true, then the DSC command is not included in the xfer->txData, but specified by xfer->dscCmd. */ txDataSize = xfer->sendDscCmd ? (uint32_t)xfer->txDataSize + 1U : (uint32_t)xfer->txDataSize; /* Short packet. */ if (txDataSize <= 2U) { if (0U == txDataSize) { wordCount = 0U; } else { txDataIndex = 0; if (xfer->sendDscCmd) { wordCount = xfer->dscCmd; } else { wordCount = xfer->txData[txDataIndex++]; } if (2U == txDataSize) { wordCount |= ((uint16_t)xfer->txData[txDataIndex] << 8U); } } } /* Long packet. */ else { wordCount = (uint16_t)txDataSize; DSI_WriteApbTxPayloadExt(base, xfer->txData, xfer->txDataSize, xfer->sendDscCmd, xfer->dscCmd); } DSI_SetApbPacketControl(base, wordCount, xfer->virtualChannel, xfer->txDataType, xfer->flags); /* Clear the interrupt flags set by previous transfer. */ DSI_GetAndClearInterruptStatus(base, &intFlags1, &intFlags2); return kStatus_Success; } /*! * brief Read the long APB packet payload. * * Read the long packet payload from RX FIFO. This function reads directly but * does not check the RX FIFO status. Upper layer should make sure there are * available data. * * param base MIPI DSI host peripheral base address. * param payload Pointer to the payload. * param payloadSize Payload size in byte. */ void DSI_ReadApbRxPayload(const MIPI_DSI_Type *base, uint8_t *payload, uint16_t payloadSize) { uint32_t tmp; for (uint16_t i = 0; i < payloadSize / 4U; i++) { tmp = base->apb->PKT_RX_PAYLOAD; payload[0] = (uint8_t)(tmp & 0xFFU); payload[1] = (uint8_t)((tmp >> 8U) & 0xFFU); payload[2] = (uint8_t)((tmp >> 16U) & 0xFFU); payload[3] = (uint8_t)((tmp >> 24U) & 0xFFU); payload += 4U; } /* Read out the remaining data. */ if (0U != (payloadSize & 0x03U)) { tmp = base->apb->PKT_RX_PAYLOAD; for (uint16_t i = 0; i < (payloadSize & 0x3U); i++) { payload[i] = (uint8_t)(tmp & 0xFFU); tmp >>= 8U; } } } /*! * brief APB data transfer using blocking method. * * Perform APB data transfer using blocking method. This function waits until all * data send or received, or timeout happens. * * param base MIPI DSI host peripheral base address. * param xfer Pointer to the transfer structure. * retval kStatus_Success Data transfer finished with no error. * retval kStatus_Timeout Transfer failed because of timeout. * retval kStatus_DSI_RxDataError RX data error, user could use ref DSI_GetRxErrorStatus * to check the error details. * retval kStatus_DSI_ErrorReportReceived Error Report packet received, user could use * ref DSI_GetAndClearHostStatus to check the error report status. * retval kStatus_DSI_NotSupported Transfer format not supported. * retval kStatus_DSI_Fail Transfer failed for other reasons. */ status_t DSI_TransferBlocking(const MIPI_DSI_Type *base, dsi_transfer_t *xfer) { status_t status; uint32_t intFlags1Old, intFlags2Old; uint32_t intFlags1New, intFlags2New; DSI_HOST_APB_PKT_IF_Type *apb = base->apb; /* Wait for the APB state idle. */ while (0U != (apb->PKT_STATUS & (uint32_t)kDSI_ApbNotIdle)) { } status = DSI_PrepareApbTransfer(base, xfer); if (kStatus_Success != status) { return status; } DSI_SendApbPacket(base); /* Make sure the transfer is started. */ while (true) { DSI_GetAndClearInterruptStatus(base, &intFlags1Old, &intFlags2Old); if (0U != (intFlags1Old & (uint32_t)kDSI_InterruptGroup1ApbNotIdle)) { break; } } /* Wait for transfer finished. */ while (true) { /* Transfer completed. */ if (0U == (apb->PKT_STATUS & (uint32_t)kDSI_ApbNotIdle)) { break; } /* Time out. */ if (0U != (base->host->RX_ERROR_STATUS & ((uint32_t)kDSI_RxErrorHtxTo | (uint32_t)kDSI_RxErrorLrxTo | (uint32_t)kDSI_RxErrorBtaTo))) { DSI_GetAndClearInterruptStatus(base, &intFlags1New, &intFlags2New); return kStatus_Timeout; } } DSI_GetAndClearInterruptStatus(base, &intFlags1New, &intFlags2New); return DSI_HandleResult(base, intFlags1Old | intFlags1New, intFlags2Old | intFlags2New, xfer); } static status_t DSI_HandleResult(const MIPI_DSI_Type *base, uint32_t intFlags1, uint32_t intFlags2, dsi_transfer_t *xfer) { uint32_t rxPktHeader; /* If hardware detect timeout. */ if (0U != (((uint32_t)kDSI_InterruptGroup1HtxTo | (uint32_t)kDSI_InterruptGroup1LrxTo | (uint32_t)kDSI_InterruptGroup1BtaTo) & intFlags1)) { return kStatus_Timeout; } /* If received data error. */ if (0U != (((uint32_t)kDSI_InterruptGroup2EccMultiBit | (uint32_t)kDSI_InterruptGroup2CrcError) & intFlags2)) { return kStatus_DSI_RxDataError; } /* If BTA is performed. */ if (0U != (xfer->flags & (uint32_t)kDSI_TransferPerformBTA)) { if (0U != (intFlags1 & DSI_INT_STATUS_ERROR_REPORT_MASK)) { return kStatus_DSI_ErrorReportReceived; } if (0U != ((uint32_t)kDSI_InterruptGroup1ApbRxHeaderReceived & intFlags1)) { rxPktHeader = DSI_GetRxPacketHeader(base); /* If received error report. */ if (kDSI_RxDataAckAndErrorReport == DSI_GetRxPacketType(rxPktHeader)) { return kStatus_DSI_ErrorReportReceived; } else { /* Only handle short packet, long packet is not supported currently. */ xfer->rxData[0] = (uint8_t)(rxPktHeader & 0xFFU); if (2U == xfer->rxDataSize) { xfer->rxData[1] = (uint8_t)((rxPktHeader >> 8U) & 0xFFU); } return kStatus_Success; } } return kStatus_Success; } else { /* Tx Done. */ if (0U != ((uint32_t)kDSI_InterruptGroup1ApbTxDone & intFlags1)) { return kStatus_Success; } } return kStatus_Fail; } /*! * brief Create the MIPI DSI handle. * * This function initializes the MIPI DSI handle which can be used for other transactional APIs. * * param base MIPI DSI host peripheral base address. * param handle Handle pointer. * param callback Callback function. * param userData User data. */ status_t DSI_TransferCreateHandle(const MIPI_DSI_Type *base, dsi_handle_t *handle, dsi_callback_t callback, void *userData) { assert(handle); uint32_t instance = DSI_GetInstance(base); /* Zero the handle */ (void)memset(handle, 0, sizeof(*handle)); /* Initialize the handle */ s_dsiHandle[instance] = handle; handle->callback = callback; handle->userData = userData; handle->isBusy = false; handle->dsi = base; s_dsiIsr = DSI_TransferHandleIRQ; #if defined(MIPI_IRQS) /* Enable interrupt in NVIC. */ EnableIRQ(s_dsiIRQ[instance]); #endif return kStatus_Success; } /*! * brief APB data transfer using interrupt method. * * Perform APB data transfer using interrupt method, when transfer finished, * upper layer could be informed through callback function. * * param base MIPI DSI host peripheral base address. * param handle pointer to dsi_handle_t structure which stores the transfer state. * param xfer Pointer to the transfer structure. * * retval kStatus_Success Data transfer started successfully. * retval kStatus_DSI_Busy Failed to start transfer because DSI is busy with pervious transfer. * retval kStatus_DSI_NotSupported Transfer format not supported. */ status_t DSI_TransferNonBlocking(const MIPI_DSI_Type *base, dsi_handle_t *handle, dsi_transfer_t *xfer) { status_t status; if ((handle->isBusy) || (0U != (base->apb->PKT_STATUS & (uint32_t)kDSI_ApbNotIdle))) { return kStatus_DSI_Busy; } handle->xfer = *xfer; status = DSI_PrepareApbTransfer(base, &handle->xfer); if (kStatus_Success != status) { return status; } DSI_SendApbPacket(base); handle->isBusy = true; /* Enable the interrupts. */ if (0U != (handle->xfer.flags & (uint32_t)kDSI_TransferPerformBTA)) { DSI_EnableInterrupts(base, DSI_INT_STATUS_TRIGGER_MASK | (uint32_t)kDSI_InterruptGroup1ApbRxHeaderReceived | (uint32_t)kDSI_InterruptGroup1ApbRxPacketReceived | (uint32_t)kDSI_InterruptGroup1BtaTo | (uint32_t)kDSI_InterruptGroup1LrxTo | (uint32_t)kDSI_InterruptGroup1HtxTo | (uint32_t)kDSI_InterruptGroup1AckTriggerReceived, (uint32_t)kDSI_InterruptGroup2EccMultiBit | (uint32_t)kDSI_InterruptGroup2CrcError); } else { DSI_EnableInterrupts(base, (uint32_t)kDSI_InterruptGroup1ApbTxDone | (uint32_t)kDSI_InterruptGroup1HtxTo, 0U); } return kStatus_Success; } /*! * brief Abort current APB data transfer. * * param base MIPI DSI host peripheral base address. * param handle pointer to dsi_handle_t structure which stores the transfer state. */ void DSI_TransferAbort(const MIPI_DSI_Type *base, dsi_handle_t *handle) { assert(handle); if (handle->isBusy) { /* Disable the interrupts. */ DSI_DisableInterrupts(base, (uint32_t)kDSI_InterruptGroup1ApbTxDone | DSI_INT_STATUS_TRIGGER_MASK | DSI_INT_STATUS_ERROR_REPORT_MASK | (uint32_t)kDSI_InterruptGroup1ApbRxHeaderReceived | (uint32_t)kDSI_InterruptGroup1ApbRxPacketReceived | (uint32_t)kDSI_InterruptGroup1BtaTo | (uint32_t)kDSI_InterruptGroup1LrxTo | (uint32_t)kDSI_InterruptGroup1HtxTo, (uint32_t)kDSI_InterruptGroup2EccMultiBit | (uint32_t)kDSI_InterruptGroup2CrcError); /* Reset transfer info. */ (void)memset(&handle->xfer, 0, sizeof(handle->xfer)); /* Reset the state to idle. */ handle->isBusy = false; } } /*! * @brief Interrupt handler for the DSI. * * @param base MIPI DSI host peripheral base address. * @param handle pointer to dsi_handle_t structure which stores the transfer state. */ /*! * brief Interrupt handler for the DSI. * * param base MIPI DSI host peripheral base address. * param handle pointer to dsi_handle_t structure which stores the transfer state. */ void DSI_TransferHandleIRQ(const MIPI_DSI_Type *base, dsi_handle_t *handle) { assert(handle); status_t status; uint32_t intFlags1, intFlags2; uint32_t timeout; base = handle->dsi; /* If no transfer in progress, return directly. */ if (!handle->isBusy) { return; } /* Make sure the transfer is completed. */ timeout = FSL_MIPI_DSI_IDLE_TIMEOUT; while (0U != (timeout--)) { if (0U == (base->apb->PKT_STATUS & (uint32_t)kDSI_ApbNotIdle)) { break; } } if (0U == timeout) { DSI_TransferAbort(base, handle); status = kStatus_Timeout; } else { /* Disable the interrupts. */ DSI_DisableInterrupts(base, (uint32_t)kDSI_InterruptGroup1ApbTxDone | DSI_INT_STATUS_TRIGGER_MASK | DSI_INT_STATUS_ERROR_REPORT_MASK | (uint32_t)kDSI_InterruptGroup1ApbRxHeaderReceived | (uint32_t)kDSI_InterruptGroup1ApbRxPacketReceived | (uint32_t)kDSI_InterruptGroup1BtaTo | (uint32_t)kDSI_InterruptGroup1LrxTo | (uint32_t)kDSI_InterruptGroup1HtxTo, (uint32_t)kDSI_InterruptGroup2EccMultiBit | (uint32_t)kDSI_InterruptGroup2CrcError); DSI_GetAndClearInterruptStatus(base, &intFlags1, &intFlags2); status = DSI_HandleResult(base, intFlags1, intFlags2, &handle->xfer); handle->isBusy = false; } if (NULL != handle->callback) { handle->callback(base, handle, status, handle->userData); } } #if defined(DSI_HOST) void MIPI_DriverIRQHandler(void); void MIPI_DriverIRQHandler(void) { /* The first parameter is not used, use the peripheral address defined in * handle. */ s_dsiIsr(NULL, s_dsiHandle[0]); } #endif