/* * Copyright 2024 NXP * * SPDX-License-Identifier: Apache-2.0 */ #ifndef ZEPHYR_SOC_ARM64_NXP_IMX95_PINCTRL_SOC_H_ #define ZEPHYR_SOC_ARM64_NXP_IMX95_PINCTRL_SOC_H_ #include #include #include "soc.h" #ifdef __cplusplus extern "C" { #endif #define PIN_CONFIG_TYPE_MUX 192 #define PIN_CONFIG_TYPE_CONFIG 193 #define PIN_CONFIG_TYPE_DAISY_ID 194 #define PIN_CONFIG_TYPE_DAISY_CFG 195 #define IOMUXC_MUX_MODE(x) IOMUXC_SW_MUX_CTL_PAD_MUX_MODE(x) #define IOMUXC_SION(x) IOMUXC_SW_MUX_CTL_PAD_SION(x) #define IOMUXC_MUXREG (IOMUXC_BASE) #define IOMUXC_CFGREG (IOMUXC_BASE + 0x204) #define IOMUXC_DAISYREG (IOMUXC_BASE + 0x408) #define IOMUXC_INPUT_SCHMITT_ENABLE_SHIFT IOMUXC_SW_PAD_CTL_PAD_HYS_SHIFT #define IOMUXC_DRIVE_OPEN_DRAIN_SHIFT IOMUXC_SW_PAD_CTL_PAD_OD_SHIFT #define IOMUXC_BIAS_PULL_DOWN_SHIFT IOMUXC_SW_PAD_CTL_PAD_PD_SHIFT #define IOMUXC_BIAS_PULL_UP_SHIFT IOMUXC_SW_PAD_CTL_PAD_PU_SHIFT #define IOMUXC_SLEW_RATE_SHIFT IOMUXC_SW_PAD_CTL_PAD_FSEL1_SHIFT #define IOMUXC_DRIVE_STRENGTH_SHIFT IOMUXC_SW_PAD_CTL_PAD_DSE_SHIFT #define IOMUXC_INPUT_ENABLE_SHIFT 23 /* Shift to a bit not used by IOMUXC_SW_PAD_CTL */ #define IOMUXC_INPUT_ENABLE(x) ((x >> IOMUXC_INPUT_ENABLE_SHIFT) & 0x1) #define Z_PINCTRL_IOMUXC_PINCFG_INIT(node_id) \ ((DT_PROP(node_id, input_schmitt_enable) << IOMUXC_INPUT_SCHMITT_ENABLE_SHIFT) | \ (DT_PROP(node_id, drive_open_drain) << IOMUXC_DRIVE_OPEN_DRAIN_SHIFT) | \ (DT_PROP(node_id, bias_pull_down) << IOMUXC_BIAS_PULL_DOWN_SHIFT) | \ (DT_PROP(node_id, bias_pull_up) << IOMUXC_BIAS_PULL_UP_SHIFT) | \ (DT_ENUM_IDX(node_id, slew_rate) << IOMUXC_SLEW_RATE_SHIFT) | \ ((~(0xff << DT_ENUM_IDX(node_id, drive_strength))) << IOMUXC_DRIVE_STRENGTH_SHIFT) | \ (DT_PROP(node_id, input_enable) << IOMUXC_INPUT_ENABLE_SHIFT)) /* This struct must be present. It is used by the mcux gpio driver */ struct pinctrl_soc_pinmux { uint32_t mux_register; /*!< IOMUXC SW_PAD_MUX register */ uint32_t config_register; /*!< IOMUXC SW_PAD_CTL register */ uint32_t input_register; /*!< IOMUXC SELECT_INPUT DAISY register */ uint8_t mux_mode: 4; /*!< Mux value for SW_PAD_MUX register */ uint32_t input_daisy: 4; /*!< Mux value for SELECT_INPUT_DAISY register */ }; struct pinctrl_soc_pin { struct pinctrl_soc_pinmux pinmux; uint32_t pin_ctrl_flags; /*!< value to write to IOMUXC_SW_PAD_CTL register */ }; typedef struct pinctrl_soc_pin pinctrl_soc_pin_t; /* This definition must be present. It is used by the mcux gpio driver */ #define IOMUXC_PINMUX(node_id) \ { \ .mux_register = DT_PROP_BY_IDX(node_id, pinmux, 0), \ .config_register = DT_PROP_BY_IDX(node_id, pinmux, 4), \ .input_register = DT_PROP_BY_IDX(node_id, pinmux, 2), \ .mux_mode = DT_PROP_BY_IDX(node_id, pinmux, 1), \ .input_daisy = DT_PROP_BY_IDX(node_id, pinmux, 3), \ } #define Z_PINCTRL_PINMUX(group_id, pin_prop, idx) \ IOMUXC_PINMUX(DT_PHANDLE_BY_IDX(group_id, pin_prop, idx)) #define Z_PINCTRL_STATE_PIN_INIT(group_id, pin_prop, idx) \ { \ .pinmux = Z_PINCTRL_PINMUX(group_id, pin_prop, idx), \ .pin_ctrl_flags = Z_PINCTRL_IOMUXC_PINCFG_INIT(group_id), \ }, #define Z_PINCTRL_STATE_PINS_INIT(node_id, prop) \ {DT_FOREACH_CHILD_VARGS(DT_PHANDLE(node_id, prop), DT_FOREACH_PROP_ELEM, pinmux, \ Z_PINCTRL_STATE_PIN_INIT)}; #ifdef __cplusplus } #endif #endif /* ZEPHYR_SOC_ARM64_NXP_IMX95_PINCTRL_SOC_H_ */