# Copyright (c) 2018 STMicroelectronics
# SPDX-License-Identifier: Apache-2.0

description: |
    When setting the int1-gpio-config/int2-gpio-config and anym-mode properties
    in a .dts or .dtsi file you may include lis2dh.h and use the macros defined there.

    Example:
    #include <zephyr/dt-bindings/sensor/lis2dh.h>

    lis2dh: lis2dh@0 {
      ...

      int1-gpio-config = <LIS2DH_DT_GPIO_INT_LEVEL_LOW>;
      int2-gpio-config = <LIS2DH_DT_GPIO_INT_LEVEL_LOW>;
      anym-mode = <LIS2DH_DT_ANYM_6D_POSITION>;
    };

include: sensor-device.yaml

properties:
  irq-gpios:
    type: phandle-array
    description: |
      The INT1 and (optional) INT2 signal connections.  These signals
      are active-high as produced by the sensor.

  int1-gpio-config:
    type: int
    default: 0
    description: |
      Select the interrupt configuration for INT1 gpio.

      The default of 0 is the most common situation to avoid multiple interrupts
      to be triggered by same event.

      - 0 # LIS2DH_DT_GPIO_INT_EDGE_BOTH
      - 1 # LIS2DH_DT_GPIO_INT_EDGE_RISING
      - 2 # LIS2DH_DT_GPIO_INT_EDGE_FALLING
      - 3 # LIS2DH_DT_GPIO_INT_LEVEL_HIGH
      - 4 # LIS2DH_DT_GPIO_INT_LEVEL_LOW

    enum: [0, 1, 2, 3, 4]

  int2-gpio-config:
    type: int
    default: 0
    description: |
      Select the interrupt configuration for INT2 gpio.

      The default of 0 is the most common situation to avoid multiple interrupts
      to be triggered by same event.

      - 0 # LIS2DH_DT_GPIO_INT_EDGE_BOTH
      - 1 # LIS2DH_DT_GPIO_INT_EDGE_RISING
      - 2 # LIS2DH_DT_GPIO_INT_EDGE_FALLING
      - 3 # LIS2DH_DT_GPIO_INT_LEVEL_HIGH
      - 4 # LIS2DH_DT_GPIO_INT_LEVEL_LOW

    enum: [0, 1, 2, 3, 4]

  disconnect-sdo-sa0-pull-up:
    type: boolean
    description: |
      Indicates the device driver should disconnect SDO/SA0 pull-up
      during device initialization (e.g. to save current
      leakage). Note that only subset of devices supported by this
      binding have SDO/SA0 pull-up (e.g. LIS2DH12, LIS3DH).

  anym-on-int1:
    type: boolean
    description: |
      Indicates that the device driver should use interrupt 1
      for any movement. This is for boards that only have one
      interrupt line connected from the sensor to the processor.

  anym-no-latch:
    type: boolean
    description: |
      Disable the latching of interrupts for any movement.

  anym-mode:
    type: int
    default: 0
    description: |
      Select the interrupt mode for any movement.

      The default of 0 is the power-on-reset value.

      - 0 # LIS2DH_DT_ANYM_OR_COMBINATION
      - 1 # LIS2DH_DT_ANYM_6D_MOVEMENT
      - 2 # LIS2DH_DT_ANYM_AND_COMBINATION
      - 3 # LIS2DH_DT_ANYM_6D_POSITION

    enum: [0, 1, 2, 3]