Bluetooth: A2DP Shell
#####################

The :code:`a2dp` command exposes parts of the A2DP API.

The following examples assume that you have two devices already connected.

Here is a example connecting two devices:
 * Source and Sink sides register a2dp callbacks. using :code:`a2dp register_cb`.
 * Source and Sink sides register stream endpoints. using :code:`a2dp register_ep source sbc` and :code:`a2dp register_ep sink sbc`.
 * Source establish A2dp connection. It will create the AVDTP Signaling and Media L2CAP channels. using :code:`a2dp connect`.
 * Source and Sink side can discover remote device's stream endpoints. using :code:`a2dp discover_peer_eps`
 * Source or Sink configure the stream to create the stream after discover remote's endpoints. using :code:`a2dp configure`.
 * Source or Sink establish the stream. using :code:`a2dp establish`.
 * Source or Sink start the media. using :code:`a2dp start`.
 * Source test the media sending. using :code:`a2dp send_media` to send one test packet data.
 * Source or Sink suspend the media. using :code:`a2dp suspend`.
 * Source or Sink release the media. using :code:`a2dp release`.

.. tabs::

        .. group-tab:: Device A (Audio Source Side)

                .. code-block:: console

                        uart:~$ a2dp register_cb
                        success
                        uart:~$ a2dp register_ep source sbc
                        SBC source endpoint is registered
                        uart:~$ a2dp connect
                        Bonded with XX:XX:XX:XX:XX:XX
                        Security changed: XX:XX:XX:XX:XX:XX level 2
                        a2dp connected
                        uart:~$ a2dp discover_peer_eps
                        endpoint id: 1, (sink), (idle):
                          codec type: SBC
                          sample frequency:
                                  44100
                                  48000
                          channel mode:
                                  Mono
                                  Stereo
                                  Joint-Stereo
                          Block Length:
                                  16
                          Subbands:
                                  8
                          Allocation Method:
                                  Loudness
                          Bitpool Range: 18 - 35
                        uart:~$ a2dp configure
                        success to configure
                        stream configured
                        uart:~$ a2dp establish
                        success to establish
                        stream established
                        uart:~$ a2dp start
                        success to start
                        stream started
                        uart:~$ a2dp send_media
                        frames num: 1, data length: 160
                        data: 1, 2, 3, 4, 5, 6 ......
                        uart:~$ a2dp suspend
                        success to suspend
                        stream suspended
                        uart:~$ a2dp release
                        success to release
                        stream released

        .. group-tab:: Device B (Audio Sink Side)

                .. code-block:: console

                        uart:~$ a2dp register_cb
                        success
                        uart:~$ a2dp register_ep sink sbc
                        SBC sink endpoint is registered
                        <after a2dp connect>
                        Connected: XX:XX:XX:XX:XX:XX
                        Bonded with XX:XX:XX:XX:XX:XX
                        Security changed: XX:XX:XX:XX:XX:XX level 2
                        a2dp connected
                        <after a2dp configure of source side>
                        receive requesting config and accept
                        sample rate 44100Hz
                        stream configured
                        <after a2dp establish of source side>
                        receive requesting establishment and accept
                        stream established
                        <after a2dp start of source side>
                        receive requesting start and accept
                        stream started
                        <after a2dp send_media of source side>
                        received, num of frames: 1, data length: 160
                        data: 1, 2, 3, 4, 5, 6 ......
                        <after a2dp suspend of source side>
                        receive requesting suspend and accept
                        stream suspended
                        <after a2dp release of source side>
                        receive requesting release and accept
                        stream released
                        ...