/*
 * Copyright (c) 2017 BayLibre, SAS
 *
 * SPDX-License-Identifier: Apache-2.0
 */

/dts-v1/;
#include <st/f0/stm32f072Xb.dtsi>
#include <st/f0/stm32f072v(8-b)tx-pinctrl.dtsi>
#include <zephyr/dt-bindings/input/input-event-codes.h>

/ {
	model = "STMicroelectronics STM32F072-EVAL board";
	compatible = "st,stm32f072-eval";

	chosen {
		zephyr,console = &usart2;
		zephyr,shell-uart = &usart2;
		zephyr,sram = &sram0;
		zephyr,flash = &flash0;
	};

	leds {
		compatible = "gpio-leds";
		green_led_1: led_1 {
			gpios = <&gpiod 8 GPIO_ACTIVE_HIGH>;
			label = "User LD1";
		};
		orange_led_2: led_2 {
			gpios = <&gpiod 9 GPIO_ACTIVE_HIGH>;
			label = "User LD2";
		};
		red_led_3: led_3 {
			gpios = <&gpiod 10 GPIO_ACTIVE_HIGH>;
			label = "User LD3";
		};
		blue_led_4: led_4 {
			gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
			label = "User LD4";
		};
	};

	gpio_keys {
		compatible = "gpio-keys";
		tamper: tamper_button {
			label = "tamper button";
			gpios = <&gpioc 13 GPIO_ACTIVE_LOW>;
			zephyr,code = <INPUT_KEY_0>;
		};
		joy_sel: joystick_selection {
			label = "joystick selection";
			gpios = <&gpioa 0 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>;
			zephyr,code = <INPUT_KEY_ENTER>;
		};
		joy_down: joystick_down {
			label = "joystick down";
			gpios = <&gpiof 10 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>;
			zephyr,code = <INPUT_KEY_DOWN>;
		};
		joy_up: joystick_up {
			label = "joystick up";
			gpios = <&gpiof 9 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>;
			zephyr,code = <INPUT_KEY_UP>;
		};
		joy_left: joystick_left {
			label = "joystick left";
			gpios = <&gpiof 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>;
			zephyr,code = <INPUT_KEY_LEFT>;
		};
		joy_right: joystick_right {
			label = "joystick right";
			gpios = <&gpioe 3 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>;
			zephyr,code = <INPUT_KEY_RIGHT>;
		};
	};

	aliases {
		led0 = &green_led_1;
		led1 = &orange_led_2;
		led2 = &red_led_3;
		led3 = &blue_led_4;
		sw0 = &joy_sel;
		watchdog0 = &iwdg;
	};
};

&clk_hse {
	clock-frequency = <DT_FREQ_M(8)>;
	status = "okay";
};

&pll {
	prediv = <1>;
	mul = <6>;
	clocks = <&clk_hse>;
	status = "okay";
};

&rcc {
	clocks = <&pll>;
	clock-frequency = <DT_FREQ_M(48)>;
	ahb-prescaler = <1>;
	apb1-prescaler = <1>;
};

&usart2 {
	pinctrl-0 = <&usart2_tx_pd5 &usart2_rx_pd6>;
	pinctrl-names = "default";
	current-speed = <115200>;
	status = "okay";
};

&iwdg {
	status = "okay";
};