/* * Copyright (c) 2021 Tom Owen * * SPDX-License-Identifier: Apache-2.0 */ /dts-v1/; #include #include #include "arduino_r3_connector.dtsi" #include / { model = "STMicroelectronics STM32F446ZE-NUCLEO board"; compatible = "st,stm32f446ze-nucleo"; chosen { zephyr,console = &usart3; zephyr,shell-uart = &usart3; zephyr,sram = &sram0; zephyr,flash = &flash0; zephyr,canbus = &can1; }; leds: leds { compatible = "gpio-leds"; green_led_1: led_1 { gpios = <&gpiob 0 GPIO_ACTIVE_HIGH>; label = "User LD1"; }; blue_led_2: led_2 { gpios = <&gpiob 7 GPIO_ACTIVE_HIGH>; label = "User LD2"; }; red_led_3: led_3 { gpios = <&gpiob 14 GPIO_ACTIVE_HIGH>; label = "User LD3"; }; }; gpio_keys { compatible = "gpio-keys"; user_button: button { label = "User"; gpios = <&gpioc 13 GPIO_ACTIVE_LOW>; zephyr,code = ; }; }; aliases { led0 = &green_led_1; led1 = &blue_led_2; led2 = &red_led_3; sw0 = &user_button; volt-sensor0 = &vref; volt-sensor1 = &vbat; }; }; &clk_lsi { status = "okay"; }; &clk_hse { hse-bypass; clock-frequency = ; /* STLink 8MHz clock */ status = "okay"; }; &pll { div-m = <8>; mul-n = <336>; div-p = <2>; div-q = <7>; clocks = <&clk_hse>; status = "okay"; }; &rcc { clocks = <&pll>; clock-frequency = ; /* highest value to get a precise USB clock */ ahb-prescaler = <1>; apb1-prescaler = <4>; apb2-prescaler = <2>; }; &adc1 { pinctrl-0 = <&adc1_in0_pa0>; pinctrl-names = "default"; st,adc-clock-source = "SYNC"; st,adc-prescaler = <2>; status = "okay"; }; &dac1 { status = "okay"; pinctrl-0 = <&dac_out1_pa4>; pinctrl-names = "default"; }; &usart2 { pinctrl-0 = <&usart2_tx_pd5 &usart2_rx_pd6>; pinctrl-names = "default"; current-speed = <115200>; status = "okay"; }; &usart3 { pinctrl-0 = <&usart3_tx_pd8 &usart3_rx_pd9>; pinctrl-names = "default"; current-speed = <115200>; status = "okay"; }; &usart6 { pinctrl-0 = <&usart6_tx_pg14 &usart6_rx_pg9>; pinctrl-names = "default"; current-speed = <115200>; status = "okay"; }; &i2c1 { pinctrl-0 = <&i2c1_scl_pb8 &i2c1_sda_pb9>; pinctrl-names = "default"; status = "okay"; clock-frequency = ; }; &i2c2 { pinctrl-0 = <&i2c2_scl_pf1 &i2c2_sda_pf0>; pinctrl-names = "default"; status = "okay"; clock-frequency = ; }; &spi1 { pinctrl-0 = <&spi1_sck_pa5 &spi1_miso_pa6 &spi1_mosi_pa7>; pinctrl-names = "default"; cs-gpios = <&gpiod 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; status = "okay"; }; &spi2 { pinctrl-0 = <&spi2_nss_pb12 &spi2_sck_pb13 &spi2_miso_pb14 &spi2_mosi_pb15>; pinctrl-names = "default"; status = "okay"; }; zephyr_udc0: &usbotg_fs { pinctrl-0 = <&usb_otg_fs_dm_pa11 &usb_otg_fs_dp_pa12 &usb_otg_fs_id_pa10>; pinctrl-names = "default"; status = "okay"; }; &timers1 { status = "okay"; pwm1: pwm { status = "okay"; pinctrl-0 = <&tim1_ch1_pe9>; pinctrl-names = "default"; }; }; &rtc { clocks = <&rcc STM32_CLOCK_BUS_APB1 0x10000000>, <&rcc STM32_SRC_LSI RTC_SEL(2)>; status = "okay"; }; &backup_sram { status = "okay"; }; &can1 { pinctrl-0 = <&can1_rx_pd0 &can1_tx_pd1>; pinctrl-names = "default"; status = "okay"; }; &flash0 { partitions { compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; boot_partition: partition@0 { label = "mcuboot"; reg = <0x00000000 DT_SIZE_K(64)>; read-only; }; /* * The flash starting at 0x00010000 and ending at * 0x0001ffff (sectors 16-31) is reserved for use * by the application. */ storage_partition: partition@10000 { label = "storage"; reg = <0x00010000 DT_SIZE_K(64)>; }; slot0_partition: partition@20000 { label = "image-0"; reg = <0x00020000 DT_SIZE_K(128)>; }; slot1_partition: partition@40000 { label = "image-1"; reg = <0x00040000 DT_SIZE_K(128)>; }; scratch_partition: partition@60000 { label = "image-scratch"; reg = <0x00060000 DT_SIZE_K(128)>; }; }; }; &vref { status = "okay"; }; &vbat { status = "okay"; };