/*
 * Copyright (c) 2024 Renesas Electronics Corporation
 * SPDX-License-Identifier: Apache-2.0
 */

/dts-v1/;

#include <renesas/ra/ra6/r7fa6m5bh3cfc.dtsi>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input-event-codes.h>
#include <zephyr/dt-bindings/adc/adc.h>

#include "ek_ra6m5-pinctrl.dtsi"

/ {
	model = "Renesas EK-RA6M5";
	compatible = "renesas,ra6m5", "renesas,ra";

	chosen {
		zephyr,sram = &sram0;
		zephyr,flash = &flash0;
		zephyr,console = &uart0;
		zephyr,shell-uart = &uart0;
	};

	leds {
		compatible = "gpio-leds";
		led1: led1 {
			gpios = <&ioport0 6 GPIO_ACTIVE_HIGH>;
			label = "LED1";
		};
		led2: led2 {
			gpios = <&ioport0 7 GPIO_ACTIVE_HIGH>;
			label = "LED2";
		};
		led3: led3 {
			gpios = <&ioport0 8 GPIO_ACTIVE_HIGH>;
			label = "LED3";
		};
	};

	buttons {
		compatible = "gpio-keys";
		button0: s1 {
			gpios = <&ioport0 5 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>;
			label = "Push button switch 1";
			zephyr,code = <INPUT_KEY_0>;
		};
		button1: s2 {
			gpios = <&ioport0 4 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>;
			label = "Push button switch 2";
			zephyr,code = <INPUT_KEY_1>;
		};
	};

	aliases {
		led0 = &led1;
		sw0 = &button0;
		sw1 = &button1;
	};
};

&sci0 {
	pinctrl-0 = <&sci0_default>;
	pinctrl-names = "default";
	status = "okay";
	uart0: uart {
		current-speed = <115200>;
		status = "okay";
	};
};

&iic1 {
	status = "okay";
	#address-cells = <1>;
	#size-cells = <0>;
	interrupts = <91 1>, <92 1>, <93 1>, <94 1>;
	interrupt-names = "rxi", "txi", "tei", "eri";
	clock-frequency = <DT_FREQ_M(1)>;
	pinctrl-0 = <&iic1_default>;
	pinctrl-names = "default";
};

&spi0 {
	pinctrl-0 = <&spi0_default>;
	pinctrl-names = "default";
	status = "okay";
};

&ioport0 {
	status = "okay";
};

&xtal {
	clock-frequency = <DT_FREQ_M(24)>;
	mosel = <0>;
	#clock-cells = <0>;
	status = "okay";
};

&subclk {
	status = "okay";
};

&pll {
	clocks = <&xtal>;
	div = <3>;
	mul = <25 0>;
	status = "okay";
};

&usbhs {
	pinctrl-0 = <&usbhs_default>;
	pinctrl-names = "default";
	maximum-speed = "high-speed";
	status = "okay";
	zephyr_udc0: udc {
		status = "okay";
	};
};

&usbhs_phy {
	phys-clock-src = "xtal";
};

&adc0 {
	status = "okay";
	pinctrl-0 = <&adc0_default>;
	pinctrl-names = "default";
};

&port_irq9 {
	interrupts = <41 12>;
	status = "okay";
};

&port_irq10 {
	interrupts = <42 12>;
	status = "okay";
};

&pwm1 {
	pinctrl-0 = <&pwm1_default>;
	pinctrl-names = "default";
	interrupts = <63 1>, <64 1>;
	interrupt-names = "gtioca", "overflow";
	status = "okay";
};