/*
 * Copyright (c) 2018 Phytec Messtechnik GmbH
 * Copyright (c) 2017 Linaro Limited
 *
 * SPDX-License-Identifier: Apache-2.0
 */

#include <nordic/nrf52840_partition.dtsi>
#include "reel_board-pinctrl.dtsi"
#include <zephyr/dt-bindings/input/input-event-codes.h>

/ {
	chosen {
		zephyr,ieee802154 = &ieee802154;
	};

	leds {
		compatible = "gpio-leds";
		red_led: led_0 {
			gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
			label = "User D3 red";
		};
		green_led: led_1 {
			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
			label = "User D3 green";
		};
		blue_led: led_2 {
			gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
			label = "User D3 blue";
		};
	};

	pwmleds {
		compatible = "pwm-leds";
		red_pwm_led: pwm_led_0 {
			pwms = <&pwm0 1 PWM_MSEC(20) PWM_POLARITY_INVERTED>;
		};
		green_pwm_led: pwm_led_1 {
			pwms = <&pwm0 2 PWM_MSEC(20) PWM_POLARITY_INVERTED>;
		};
		blue_pwm_led: pwm_led_2 {
			pwms = <&pwm0 3 PWM_MSEC(20) PWM_POLARITY_INVERTED>;
		};
	};

	gpio_keys {
		compatible = "gpio-keys";
		user_button: button_0 {
			gpios = <&gpio0 7 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>;
			label = "User Button";
			zephyr,code = <INPUT_KEY_0>;
		};
	};

	arduino_header: connector {
		compatible = "arduino-header-r3";
		#gpio-cells = <2>;
		gpio-map-mask = <0xffffffff 0xffffffc0>;
		gpio-map-pass-thru = <0 0x3f>;
		gpio-map = <0 0 &gpio0 3 0>,	/* A0 */
			   <1 0 &gpio0 4 0>,	/* A1 */
			   <2 0 &gpio0 28 0>,	/* A2 */
			   <3 0 &gpio0 29 0>,	/* A3 */
			   <4 0 &gpio0 30 0>,	/* A4 */
			   <5 0 &gpio0 31 0>,	/* A5 */
			   <6 0 &gpio1 1 0>,	/* D0 */
			   <7 0 &gpio1 2 0>,	/* D1 */
			   <8 0 &gpio1 3 0>,	/* D2 */
			   <9 0 &gpio1 4 0>,	/* D3 */
			   <10 0 &gpio1 5 0>,	/* D4 */
			   <11 0 &gpio1 6 0>,	/* D5 */
			   <12 0 &gpio1 7 0>,	/* D6 */
			   <13 0 &gpio1 8 0>,	/* D7 */
			   <14 0 &gpio1 10 0>,	/* D8 */
			   <15 0 &gpio1 11 0>,	/* D9 */
			   <16 0 &gpio1 12 0>,	/* D10 */
			   <17 0 &gpio1 13 0>,	/* D11 */
			   <18 0 &gpio1 14 0>,	/* D12 */
			   <19 0 &gpio1 15 0>,	/* D13 */
			   <20 0 &gpio0 26 0>,	/* D14 */
			   <21 0 &gpio0 27 0>;	/* D15 */
	};

	aliases {
		led0 = &red_led;
		led1 = &green_led;
		led2 = &blue_led;
		pwm-led0 = &red_pwm_led;
		pwm-led1 = &green_pwm_led;
		pwm-led2 = &blue_pwm_led;
		red-pwm-led = &red_pwm_led;
		green-pwm-led = &green_pwm_led;
		blue-pwm-led = &blue_pwm_led;
		sw0 = &user_button;
		accel0 = &mma8642fc;
	};
};

&reg1 {
	regulator-initial-mode = <NRF5X_REG_MODE_DCDC>;
};

&uicr {
	gpio-as-nreset;
};

&gpiote {
	status = "okay";
};

&gpio0 {
	status = "okay";
};

&gpio1 {
	status = "okay";
};

&uart0 {
	compatible = "nordic,nrf-uart";
	current-speed = <115200>;
	status = "okay";
	pinctrl-0 = <&uart0_default>;
	pinctrl-1 = <&uart0_sleep>;
	pinctrl-names = "default", "sleep";
};

arduino_serial: &uart1 {
	status = "okay";
	current-speed = <115200>;
	pinctrl-0 = <&uart1_default>;
	pinctrl-1 = <&uart1_sleep>;
	pinctrl-names = "default", "sleep";
};

arduino_i2c: &i2c0 {
	compatible = "nordic,nrf-twim";
	status = "okay";
	clock-frequency = <I2C_BITRATE_FAST>;

	pinctrl-0 = <&i2c0_default>;
	pinctrl-1 = <&i2c0_sleep>;
	pinctrl-names = "default", "sleep";
	mma8642fc: mma8652fc@1d {
		compatible = "nxp,fxos8700","nxp,mma8652fc";
		reg = <0x1d>;
		int1-gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
		int2-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
	};

	ti_hdc@43 {
		compatible = "ti,hdc","ti,hdc1010";
		reg = <0x43>;
		drdy-gpios = <&gpio0 22 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
	};

	apds9960@39 {
		compatible = "avago,apds9960";
		reg = <0x39>;
		int-gpios = <&gpio0 23 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
	};
};

&pwm0 {
	status = "okay";
	pinctrl-0 = <&pwm0_default>;
	pinctrl-1 = <&pwm0_sleep>;
	pinctrl-names = "default", "sleep";
};

&ieee802154 {
	status = "okay";
};

arduino_spi: &spi3 {
	status = "okay";
	cs-gpios = <&arduino_header 16 GPIO_ACTIVE_LOW>; /* D10 */
	pinctrl-0 = <&spi3_default>;
	pinctrl-1 = <&spi3_sleep>;
	pinctrl-names = "default", "sleep";
};

zephyr_udc0: &usbd {
	compatible = "nordic,nrf-usbd";
	status = "okay";
};