/* * Copyright (c) 2022 Martin Jäger * * SPDX-License-Identifier: Apache-2.0 */ /dts-v1/; #include #include / { model = "Olimex LoRa STM32WL DevKit"; compatible = "olimex,lora-stm32wl-devkit"; chosen { zephyr,console = &usart1; zephyr,shell-uart = &usart1; zephyr,sram = &sram0; zephyr,flash = &flash0; zephyr,code-partition = &slot0_partition; }; leds { compatible = "gpio-leds"; green_led_1: led_0 { gpios = <&gpioa 15 GPIO_ACTIVE_HIGH>; label = "User LED1"; }; }; gpio_keys { compatible = "gpio-keys"; user_button: button_0 { label = "SW2"; gpios = <&gpioa 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; zephyr,code = ; }; }; aliases { led0 = &green_led_1; sw0 = &user_button; lora0 = &lora; watchdog0 = &iwdg; }; }; stm32_lp_tick_source: &lptim1 { clocks = <&rcc STM32_CLOCK_BUS_APB1 0x80000000>, <&rcc STM32_SRC_LSI LPTIM1_SEL(1)>; status = "okay"; }; &clk_lsi { status = "okay"; }; &pll { div-m = <1>; mul-n = <6>; div-r = <2>; div-q = <2>; clocks = <&clk_hsi>; status = "okay"; }; &rcc { clocks = <&pll>; clock-frequency = ; cpu1-prescaler = <1>; ahb3-prescaler = <1>; apb1-prescaler = <1>; apb2-prescaler = <1>; }; uext_serial: &lpuart1 { pinctrl-0 = <&lpuart1_tx_pa2 &lpuart1_rx_pa3>; pinctrl-names = "default"; current-speed = <115200>; status = "okay"; }; &usart1 { pinctrl-0 = <&usart1_tx_pb6 &usart1_rx_pb7>; pinctrl-names = "default"; current-speed = <115200>; status = "okay"; }; uext_i2c: &i2c1 { pinctrl-0 = <&i2c1_scl_pa9 &i2c1_sda_pa10>; pinctrl-names = "default"; status = "okay"; clock-frequency = ; bme280: bme280@77 { compatible = "bosch,bme280"; status = "okay"; reg = <0x77>; }; iis2mdc@1e { compatible = "st,iis2mdc"; reg = <0x1e>; drdy-gpios = <&gpioa 8 GPIO_ACTIVE_HIGH>; }; }; uext_spi: &spi1 { pinctrl-0 = <&spi1_nss_pa4 &spi1_sck_pa5 &spi1_miso_pa11 &spi1_mosi_pa7>; pinctrl-names = "default"; status = "okay"; }; &rtc { clocks = <&rcc STM32_CLOCK_BUS_APB1 0x00000400>, <&rcc STM32_SRC_LSI RTC_SEL(2)>; status = "okay"; }; &iwdg { status = "okay"; }; &aes { status = "okay"; }; &rng { status = "okay"; }; &flash0 { partitions { compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; boot_partition: partition@0 { label = "mcuboot"; reg = <0x00000000 DT_SIZE_K(32)>; read-only; }; slot0_partition: partition@8000 { label = "image-0"; reg = <0x00008000 DT_SIZE_K(108)>; }; slot1_partition: partition@23000 { label = "image-1"; reg = <0x00023000 DT_SIZE_K(108)>; }; storage_partition: partition@3e000 { label = "storage"; reg = <0x0003e000 DT_SIZE_K(8)>; }; }; };