/*
 * Copyright (c) 2022 AVSystem Sławomir Wolf Sp.j. (AVSystem)
 *
 * SPDX-License-Identifier: Apache-2.0
 */
/dts-v1/;

#include <espressif/esp32/esp32_pico_d4.dtsi>
#include "m5stickc_plus-pinctrl.dtsi"
#include <zephyr/dt-bindings/input/input-event-codes.h>
#include <zephyr/dt-bindings/regulator/axp192.h>
#include <zephyr/dt-bindings/mipi_dbi/mipi_dbi.h>
#include <espressif/partitions_0x1000_amp.dtsi>

/ {
	model = "M5StickC Plus PROCPU";
	compatible = "m5stack,m5stickc-plus";

	aliases {
		led0 = &red_led;
		sw0 = &user_button_0;
		sw1 = &user_button_1;
		uart-0 = &uart0;
		i2c-0 = &i2c0;
		watchdog0 = &wdt0;
		accel0 = &mpu6886;
		rtc = &bm8563;
	};

	chosen {
		zephyr,sram = &sram1;
		zephyr,console = &uart0;
		zephyr,shell-uart = &uart0;
		zephyr,flash = &flash0;
		zephyr,code-partition = &slot0_partition;
		zephyr,rtc = &bm8563;
		zephyr,display = &st7789v;
		zephyr,bt-hci = &esp32_bt_hci;
	};

	leds {
		compatible = "gpio-leds";

		red_led: led_0 {
			gpios =  <&gpio0 10 GPIO_ACTIVE_HIGH>;
			label = "Red - LED0";
		};
	};

	gpio_keys {
		compatible = "gpio-keys";

		user_button_0: button_0 {
			label = "User button 0";
			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
			zephyr,code = <INPUT_KEY_0>;
		};
		user_button_1: button_1 {
			label = "User button 1";
			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
			zephyr,code = <INPUT_KEY_1>;
		};
	};

	mipi_dbi {
		compatible = "zephyr,mipi-dbi-spi";
		spi-dev = <&spi3>;
		dc-gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
		reset-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
		write-only;
		#address-cells = <1>;
		#size-cells = <0>;

		st7789v: st7789v@0 {
			compatible = "sitronix,st7789v";
			reg = <0>;
			mipi-max-frequency = <20000000>;

			width = <135>;
			height = <240>;
			x-offset = <53>;
			y-offset = <40>;

			vcom = <0x28>;
			gctrl = <0x35>;
			vrhs = <0x10>;
			vdvs = <0x20>;
			mdac = <0x00>;
			gamma = <0x01>;
			colmod = <0x55>;
			lcm = <0x2c>;
			porch-param = [0c 0c 00 33 33];
			cmd2en-param = [5a 69 02 00];
			pwctrl1-param = [a4 a1];
			pvgam-param = [d0 00 02 07 0a 28 32 44 42 06 0e 12 14 17];
			nvgam-param = [d0 00 02 07 0a 28 31 54 47 0e 1c 17 1b 1e];
			ram-param = [00 F0];
			rgb-param = [40 02 14];
			mipi-mode = "MIPI_DBI_MODE_SPI_4WIRE";
		};
	};
};

&uart0 {
	status = "okay";
	current-speed = <115200>;
	pinctrl-0 = <&uart0_tx_gpio1 &uart0_rx_gpio3>;
	pinctrl-names = "default";
};

&gpio0 {
	status = "okay";
};

&gpio1 {
	status = "okay";
};

/* IMU MPU-6886, RTC BM8563, PMU AXP192 */
&i2c0 {
	status = "okay";
	clock-frequency = <I2C_BITRATE_FAST>;
	sda-gpios = <&gpio0 21 GPIO_OPEN_DRAIN>;
	scl-gpios = <&gpio0 22 GPIO_OPEN_DRAIN>;
	pinctrl-0 = <&i2c0_default>;
	scl-timeout-us = <0>;
	pinctrl-names = "default";

	axp192_pmic: axp192@34 {
		compatible = "x-powers,axp192";
		reg = <0x34>;
		status = "okay";

		axp192_regulator: axp192_regulator {
			compatible = "x-powers,axp192-regulator";
			status = "okay";

			vdd_mcu: DCDC1 {
				regulator-init-microvolt = <3350000>;
				regulator-min-microvolt = <3200000>;
				regulator-max-microvolt = <3400000>;
				regulator-initial-mode = <AXP192_DCDC_MODE_AUTO>;
				regulator-boot-on;
				regulator-always-on;
			};

			lcd_bl: LDO2 {
				regulator-init-microvolt = <2800000>;
				regulator-min-microvolt = <1800000>;
				regulator-max-microvolt = <3000000>;
				regulator-boot-on;
			};

			lcd_logic: LDO3 {
				regulator-init-microvolt = <3000000>;
			};
		};
		axp192_gpio: axp192_gpio {
			compatible = "x-powers,axp192-gpio";
			gpio-controller;
			#gpio-cells = <2>;
			ngpios = <6>;
			status = "okay";
		};
	};

	mpu6886: mpu6886@68 {
		status = "okay";
		compatible = "invensense,mpu6050";
		reg = <0x68>;
	};

	bm8563: bm8563@51 {
		compatible = "nxp,pcf8563";
		reg = <0x51>;
		status = "okay";
	};
};

&spi2 {
	#address-cells = <1>;
	#size-cells = <0>;
	status = "okay";
	pinctrl-0 = <&spim2_miso_gpio12 &spim2_mosi_gpio11
				&spim2_sclk_gpio14 &spim2_csel_gpio16>;
	pinctrl-names = "default";
};

/* LCD TFT 1.14", 135x240 px, ST7789v2 */
&spi3 {
	#address-cells = <1>;
	#size-cells = <0>;
	status = "okay";
	pinctrl-0 = <&spim3_default>;
	pinctrl-names = "default";
};

&timer0 {
	status = "okay";
};

&timer1 {
	status = "okay";
};

&timer2 {
	status = "okay";
};

&timer3 {
	status = "okay";
};

&trng0 {
	status = "okay";
};

&esp32_bt_hci {
	status = "okay";
};