.. _mimxrt1010_evk: NXP MIMXRT1010-EVK ################## Overview ******** The i.MX RT1010 offer a new entry-point into the i.MX RT crossover processor series by providing the lowest-cost LQFP package option, combined with the high performance and ease-of-use known throughout the entire i.MX RT series. This device is fully supported by NXP’s MCUXpresso Software and Tools. .. image:: mimxrt1010_evk.jpg :align: center :alt: MIMXRT1010-EVK Hardware ******** - MIMXRT1011DAE5A MCU - Memory - 128 Mbit QSPI Flash - Connectivity - Micro USB host and OTG connectors - Arduino interface - Audio - Audio Codec - 4-pole audio headphone jack - External speaker connection - Microphone - Debug - JTAG 10-pin connector - OpenSDA with DAPLink For more information about the MIMXRT1010 SoC and MIMXRT1010-EVK board, see these references: - `i.MX RT1010 Website`_ - `i.MX RT1010 Datasheet`_ - `i.MX RT1010 Reference Manual`_ - `MIMXRT1010-EVK Website`_ - `MIMXRT1010-EVK User Guide`_ - `MIMXRT1010-EVK Design Files`_ External Memory =============== This platform has the following external memories: +--------------------+------------+-------------------------------------+ | Device | Controller | Status | +====================+============+=====================================+ | AT25SF128A | FLEXSPI | Enabled via flash configurationn | | | | block, which sets up FLEXSPI at | | | | boot time. | +--------------------+------------+-------------------------------------+ Supported Features ================== The mimxrt1010_evk board configuration supports the hardware features listed below. For additional features not yet supported, please also refer to the :ref:`mimxrt1064_evk` , which is the superset board in NXP's i.MX RT10xx family. NXP prioritizes enabling the superset board with NXP's Full Platform Support for Zephyr. Therefore, the mimxrt1064_evk board may have additional features already supported, which can also be re-used on this mimxrt1010_evk board: +-----------+------------+-------------------------------------+ | Interface | Controller | Driver/Component | +===========+============+=====================================+ | NVIC | on-chip | nested vector interrupt controller | +-----------+------------+-------------------------------------+ | SYSTICK | on-chip | systick | +-----------+------------+-------------------------------------+ | GPIO | on-chip | gpio | +-----------+------------+-------------------------------------+ | SPI | on-chip | spi | +-----------+------------+-------------------------------------+ | I2C | on-chip | i2c | +-----------+------------+-------------------------------------+ | UART | on-chip | serial port-polling; | | | | serial port-interrupt | +-----------+------------+-------------------------------------+ | USB | on-chip | USB device | +-----------+------------+-------------------------------------+ | ADC | on-chip | adc | +-----------+------------+-------------------------------------+ | GPT | on-chip | gpt | +-----------+------------+-------------------------------------+ | TRNG | on-chip | entropy | +-----------+------------+-------------------------------------+ The default configuration can be found in the defconfig file: ``boards/arm/mimxrt1010_evk/mimxrt1010_evk_defconfig`` Other hardware features are not currently supported by the port. Connections and I/Os ==================== The MIMXRT1010 SoC has five pairs of pinmux/gpio controllers. +---------------+-----------------+---------------------------+ | Name | Function | Usage | +===============+=================+===========================+ | GPIO_11 | GPIO | LED | +---------------+-----------------+---------------------------+ | GPIO_SD_05 | GPIO | SW4 | +---------------+-----------------+---------------------------+ | GPIO_10 | LPUART1_TX | UART Console | +---------------+-----------------+---------------------------+ | GPIO_09 | LPUART1_RX | UART Console | +---------------+-----------------+---------------------------+ | GPIO_01 | LPI2C1_SDA | I2C SDA | +---------------+-----------------+---------------------------+ | GPIO_02 | LPI2C1_CLK | I2C SCL | +---------------+-----------------+---------------------------+ | GPIO_AD_03 | LPSPI1_SDI | SPI | +---------------+-----------------+---------------------------+ | GPIO_AD_04 | LPSPI1_SDO | SPI | +---------------+-----------------+---------------------------+ | GPIO_AD_05 | LPSPI1_PCS0 | SPI | +---------------+-----------------+---------------------------+ | GPIO_AD_06 | LPSPI1_SCK | SPI | +---------------+-----------------+---------------------------+ | GPIO_AD_01 | ADC | ADC1 Channel 1 | +---------------+-----------------+---------------------------+ | GPIO_AD_02 | ADC | ADC1 Channel 2 | +---------------+-----------------+---------------------------+ System Clock ============ The MIMXRT1010 SoC is configured to use SysTick as the system clock source, running at 500MHz. When power management is enabled, the 32 KHz low frequency oscillator on the board will be used as a source for the GPT timer to generate a system clock. This clock enables lower power states, at the cost of reduced resolution Serial Port =========== The MIMXRT1010 SoC has four UARTs. ``LPUART1`` is configured for the console, and the remaining are not used. Programming and Debugging ************************* Build and flash applications as usual (see :ref:`build_an_application` and :ref:`application_run` for more details). Configuring a Debug Probe ========================= A debug probe is used for both flashing and debugging the board. This board is configured by default to use the :ref:`opensda-daplink-onboard-debug-probe`, however the :ref:`pyocd-debug-host-tools` do not yet support programming the external flashes on this board so you must reconfigure the board for one of the following debug probes instead. :ref:`jlink-external-debug-probe` ------------------------------------------- Install the :ref:`jlink-debug-host-tools` and make sure they are in your search path. Attach a J-Link 10-pin connector to J55. Check that jumpers J61 and J62 are **off** (they are on by default when boards ship from the factory) to ensure SWD signals are disconnected from the OpenSDA microcontroller. Configuring a Console ===================== Regardless of your choice in debug probe, we will use the OpenSDA microcontroller as a usb-to-serial adapter for the serial console. Check that jumpers J31 and J32 are **on** (they are on by default when boards ship from the factory) to connect UART signals to the OpenSDA microcontroller. Connect a USB cable from your PC to J41. Use the following settings with your serial terminal of choice (minicom, putty, etc.): - Speed: 115200 - Data: 8 bits - Parity: None - Stop bits: 1 Flashing ======== Here is an example for the :ref:`hello_world` application. .. zephyr-app-commands:: :zephyr-app: samples/hello_world :board: mimxrt1010_evk :goals: flash Open a serial terminal, reset the board (press the SW9 button), and you should see the following message in the terminal: .. code-block:: console Hello World! mimxrt1010_evk .. _MIMXRT1010-EVK Website: https://www.nxp.com/MIMXRT1010-EVK .. _MIMXRT1010-EVK User Guide: https://www.nxp.com/webapp/Download?colCode=MIMXRT1010EVKHUG .. _MIMXRT1010-EVK Design Files: https://www.nxp.com/webapp/Download?colCode=IMXRT1010-EVK-DESIGN-FILES .. _i.MX RT1010 Website: https://www.nxp.com/imxrt1010 .. _i.MX RT1010 Datasheet: https://www.nxp.com/docs/en/data-sheet/IMXRT1010CEC.pdf .. _i.MX RT1010 Reference Manual: https://www.nxp.com/webapp/Download?colCode=IMXRT1010RM