Lines Matching refs:used
6 client (e.g., management GUI) is used to enable WPS enrollment and
68 to be used for some operations (mainly WPS activation in GO). This may
85 optional freq parameter can be used to override the first scan to use only
88 The optional dev_id option can be used to specify a single P2P peer to
89 search for. The optional delay parameter can be used to request an extra
90 delay to be used between search iterations (e.g., to free up radio
93 The optional dev_type option can be used to specify a single device type
118 other devices). Optional parameter can be used to specify the duration
121 testing. It can also be used to keep the device discoverable without
144 The optional "join" parameter can be used to indicate that this command
146 mainly used with "display" to request it to display a PIN. The "auto"
147 parameter can be used to request wpa_supplicant to automatically figure
164 used (e.g., 12345670). [display|keypad] is used with PIN method
165 to specify which PIN is used (display=dynamically generated random PIN
167 parameter can be used to request a persistent group to be formed. The
168 "persistent=<network id>" alternative can be used to pre-populate
169 SSID/passphrase configuration based on a previously used persistent
170 group where this device was the GO. The previously used parameters will
171 then be used if the local end becomes the GO in GO Negotiation (which
184 "go_intent" can be used to override the default GO Intent for this GO
187 "freq" can be used to set a forced operating channel (e.g., freq=2412
190 "provdisc" can be used to request a Provision Discovery exchange to be
191 used prior to starting GO Negotiation as a workaround with some deployed
195 "auto" can be used to request wpa_supplicant to automatically figure
199 "ssid=<hexdump>" can be used to specify the Group SSID for join
202 P2P Device or Interface address have been used in multiple groups
269 GO. Optional persistent=<network id> can be used to specify restart of
270 a persistent group. Optional freq=<freq in MHz> can be used to force
272 options can be used to request the best 2.4 GHz or 5 GHz band channel
284 Terminate a P2P group. If a new virtual network interface was used for
286 group interface is used as a parameter for this command.
294 P2P group interface (if one was used) that is in the WPS provisioning
300 This command can be used to remove the specified client from all groups
311 This command can be used to search for a P2PS service which includes
337 Session response information - Optional (used only if auto accept is TRUE)
345 This command can be used to replace the existing service request
359 State - Mandatory ASCII hex-encoded u8 (can be used to indicate svc
367 Session response information - Optional (used only if auto accept is TRUE)
391 "1f77628") that can be used to cancel the request. Directed requests
408 For UPnP, an alternative command format can be used to specify a
456 The command can be used for service discovery for P2PS enabled devices.
486 1 0300000101". This command is used only if external program is used
491 Indicate that local services have changed. This is used to increment
567 used to specify which device to invite. go_dev_addr parameter can be
568 used to override the GO device address for Invitation Request should
579 (These are used on the group interface.)
584 the AP/GO. This is used on the GO when a P2P client joins an existing
593 Enrollee to connect to the AP/GO. This is used on the GO when a P2P
635 enabled by default and this parameter is mainly used to allow testing
663 can be used to request GO to assign a unique PSK for each client during
667 the old PSK. When per-client PSK is not used, the client can still be
670 passphrase on the GO that is normally used to allow legacy stations to
677 operations. The format on these parameters is same as is used in
764 (These are used on the group interface.)
784 persistent groups. The identifier in this list is used with
836 be re-used. Group is restarted by sending "p2p_group_add persistent=0"