Lines Matching full:on
129 …r edge set to rising edge (default setting for compatibility with some ADC on other STM32 families…
157 …r edge set to rising edge (default setting for compatibility with some ADC on other STM32 families…
196 /* Equivalent mask of ADC_CHANNEL_NUMBER_MASK aligned on register LSB (bit 0) */
300 /* (feature of several watchdogs not available on all STM32 families)). */
304 /* selection on groups. */
366 …rty "rs": Software can read as well as set this bit. Writing '0' has no effect on the bit value. */
380 …8fff814UL)) /* Internal temperature sensor, address of parameter TS_CAL1: On STM32H7, temperature…
381 …8fff818UL)) /* Internal temperature sensor, address of parameter TS_CAL2: On STM32H7, temperature…
384 …1FF1E820UL)) /* Internal temperature sensor, address of parameter TS_CAL1: On STM32H7, temperature…
385 …1FF1E840UL)) /* Internal temperature sensor, address of parameter TS_CAL2: On STM32H7, temperature…
461 … @note On this STM32 series, if ADC group injected is used, some
486 * @note These parameters have an impact on ADC scope: ADC instance.
488 * of ADC group injected depends on STM32 families).
497 * (setting possible with ADC enabled without conversion on going,
498 * ADC enabled with conversion on going, ...)
523 * @note These parameters have an impact on ADC scope: ADC group regular.
533 * (setting possible with ADC enabled without conversion on going,
534 * ADC enabled with conversion on going, ...)
544 …@note On this STM32 series, setting trigger source to external trigger also set trigger polarity t…
545 …(default setting for compatibility with some ADC on other STM32 families having this setting set b…
562 …uint32_t ContinuousMode; /*!< Set ADC continuous conversion mode on ADC group regular…
583 * @note These parameters have an impact on ADC scope: ADC group injected.
593 * (setting possible with ADC enabled without conversion on going,
594 * ADC enabled with conversion on going, ...)
604 …@note On this STM32 series, setting trigger source to external trigger also set trigger polarity t…
605 …(default setting for compatibility with some ADC on other STM32 families having this setting set b…
708 …ng to register CDR) to be used with ADC configured in multimode (available on STM32 devices with s…
795 …0) /*!< ADC resolution 14 bits optimized for power consumption, available on for devices revision…
796 … ) /*!< ADC resolution 12 bits optimized for power consumption, available on for devices revision…
805 …ctions "LL_ADC_SetResolution/LL_ADC_GetResolution" with a dedicated check on DBGMCU IDCODE regist…
808 …| ADC3_CFGR_RES_0) /*!< ADC resolution 6 bits. Value available for ADC3 on STM32H72xx/3xx devic…
818 …00UL) /*!< ADC conversion data alignment: right aligned (alignment on data register LSB bi…
819 …R_ALIGN) /*!< ADC conversion data alignment: left aligned (alignment on data register MSB bi…
829 … /*!< ADC no bit shift left applied on the final ADC conver…
830 … /*!< ADC 1 bit shift left applied on the final ADC conver…
831 … /*!< ADC 2 bits shift left applied on the final ADC conver…
832 … /*!< ADC 3 bits shift left applied on the final ADC conver…
833 … /*!< ADC 4 bits shift left applied on the final ADC conver…
834 … /*!< ADC 5 bits shift left applied on the final ADC conver…
835 … /*!< ADC 6 bits shift left applied on the final ADC conver…
836 …C_CFGR2_LSHIFT_0) /*!< ADC 7 bits shift left applied on the final ADC conver…
837 … /*!< ADC 8 bits shift left applied on the final ADC conver…
838 … /*!< ADC 9 bits shift left applied on the final ADC conver…
839 … /*!< ADC 10 bits shift left applied on the final ADC conver…
840 …_CFGR2_LSHIFT_0) /*!< ADC 11 bits shift left applied on the final ADC conver…
841 … /*!< ADC 12 bits shift left applied on the final ADC conver…
842 …_CFGR2_LSHIFT_0) /*!< ADC 13 bits shift left applied on the final ADC conver…
843 …_CFGR2_LSHIFT_1) /*!< ADC 14 bits shift left applied on the final ADC conver…
844 …_CFGR2_LSHIFT_1 | ADC_CFGR2_LSHIFT_0) /*!< ADC 15 bits shift left applied on the final ADC conver…
861 …ich the offset programmed will be applied (independently of channel mapped on ADC group regular or…
862 …ich the offset programmed will be applied (independently of channel mapped on ADC group regular or…
863 …ich the offset programmed will be applied (independently of channel mapped on ADC group regular or…
864 …ich the offset programmed will be applied (independently of channel mapped on ADC group regular or…
890 …et saturation is disabled (among ADC selected offset number 1, 2, 3 or 4). On devices STM32H72xx a…
891 …set saturation is enabled (among ADC selected offset number 1, 2, 3 or 4). On devices STM32H72xx a…
908 …!< ADC offset is negative (among ADC selected offset number 1, 2, 3 or 4). On devices STM32H72xx a…
909 …!< ADC offset is positive (among ADC selected offset number 1, 2, 3 or 4). On devices STM32H72xx a…
920 #define LL_ADC_GROUP_REGULAR (0x00000001UL) /*!< ADC group regular (available on all …
921 #define LL_ADC_GROUP_INJECTED (0x00000002UL) /*!< ADC group injected (not available on…
952 …annel connected to VrefInt: Internal voltage reference. On STM32H7, ADC channel available only on …
953 …< ADC internal channel connected to Temperature sensor. On STM32H7, ADC channel available only on …
954 …er ladder of factor 1/4 to have Vbat always below Vdda. On STM32H7, ADC channel available only on …
956 …annel connected to VrefInt: Internal voltage reference. On STM32H7, ADC channel available only on …
957 …< ADC internal channel connected to Temperature sensor. On STM32H7, ADC channel available only on …
958 …er ladder of factor 1/4 to have Vbat always below Vdda. On STM32H7, ADC channel available only on …
962 …annel connected to VrefInt: Internal voltage reference. On STM32H7, ADC channel available only on …
963 …< ADC internal channel connected to Temperature sensor. On STM32H7, ADC channel available only on …
964 …er ladder of factor 1/4 to have Vbat always below Vdda. On STM32H7, ADC channel available only on …
1024 …ling phase duration is defined using @ref ADC_LL_EC_CHANNEL_SAMPLINGTIME. On devices STM32H72xx a…
1026 … is using minimal sampling time (see @ref ADC_LL_EC_CHANNEL_SAMPLINGTIME). On devices STM32H72xx a…
1029 … Trigger falling edge = stop sampling and start conversion. On devices STM32H72xx and STM32H73xx */
1060 …L) /*!< ADC conversions are not transferred by DMA. On ADC3 of devices STM3…
1061 … reached. This ADC mode is intended to be used with DMA mode non-circular. On ADC3 of devices STM3…
1062 …conversions). This ADC mode is intended to be used with DMA mode circular. On ADC3 of devices STM3…
1068 /** @defgroup ADC_LL_EC_REG_OVR_DATA_BEHAVIOR ADC group regular - Overrun behavior on conversion d…
1080 … regular sequencer disable (equivalent to sequencer of 1 rank: ADC conversion on only 1 channel) */
1186 … group injected trigger source set to SW start, without any further action on ADC group injected …
1204 …injected sequencer disable (equivalent to sequencer of 1 rank: ADC conversion on only 1 channel) */
1250 … /*!< Sampling time 2.5 ADC clock cycles. On ADC3 of devices STM3…
1251 … ADC_SMPR2_SMP10_0) /*!< Sampling time 6.5 ADC clock cycles. On ADC3 of devices STM3…
1252 …PR2_SMP10_1 ) /*!< Sampling time 12.5 ADC clock cycles. On ADC3 of devices STM3…
1253 …PR2_SMP10_1 | ADC_SMPR2_SMP10_0) /*!< Sampling time 24.5 ADC clock cycles. On ADC3 of devices STM3…
1254 … ) /*!< Sampling time 47.5 ADC clock cycles. On ADC3 of devices STM3…
1255 … | ADC_SMPR2_SMP10_0) /*!< Sampling time 92.5 ADC clock cycles. On ADC3 of devices STM3…
1256 …R2_SMP10_1 ) /*!< Sampling time 247.5 ADC clock cycles. On ADC3 of devices STM3…
1257 …R2_SMP10_1 | ADC_SMPR2_SMP10_0) /*!< Sampling time 640.5 ADC clock cycles. On ADC3 of devices STM3…
1381 … filtering, one out-of-window sample is needed to raise flag or interrupt. On ADC3 of devices STM3…
1382 … consecutives out-of-window samples are needed to raise flag or interrupt. On ADC3 of devices STM3…
1383 … consecutives out-of-window samples are needed to raise flag or interrupt. On ADC3 of devices STM3…
1384 … consecutives out-of-window samples are needed to raise flag or interrupt. On ADC3 of devices STM3…
1385 … consecutives out-of-window samples are needed to raise flag or interrupt. On ADC3 of devices STM3…
1386 … consecutives out-of-window samples are needed to raise flag or interrupt. On ADC3 of devices STM3…
1387 … consecutives out-of-window samples are needed to raise flag or interrupt. On ADC3 of devices STM3…
1388 … consecutives out-of-window samples are needed to raise flag or interrupt. On ADC3 of devices STM3…
1398 …mpling on conversions of ADC group regular. If group injected interrupts group regular: when ADC g…
1399 …mpling on conversions of ADC group regular. If group injected interrupts group regular: when ADC g…
1400 … ADC_CFGR2_JOVSE ) /*!< ADC oversampling on conversions of ADC g…
1401 …on conversions of both ADC groups regular and injected. If group injected interrupting group regul…
1510 * For details on delays values, refer to descriptions in source code
1529 /* - ADC conversion time: duration depending on ADC clock and ADC */
1552 /* Note: On this STM32 series, a minimum number of ADC clock cycles */
1683 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
1684 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
1685 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
1734 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
1735 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
1736 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
1801 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
1802 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
1803 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
1851 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
1852 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
1853 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
1882 * selected is available on the ADC instance selected.
1901 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
1902 * (2) On STM32H7, parameter available only on ADC instance: ADC2.
1903 …* @retval Value "0" if the internal channel selected is not available on the ADC instance selected.
1904 * Value "1" if the internal channel selected is available on the ADC instance selected.
1973 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
1974 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
1975 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
2065 * (0) On STM32H7, parameter available only on analog watchdog number: AWD1.\n
2066 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
2067 * (2) On STM32H7, parameter available only on ADC instance: ADC2.
2085 * analog watchdog threshold high (on 18 bits):
2108 * analog watchdog threshold high (on 18 bits):
2209 * @note On devices with only 1 ADC common instance, parameter of this macro
2404 * @note This voltage depends on user board environment: voltage level
2406 * On devices with small package, the pin Vref+ is not present
2408 * @note On this STM32 series, calibration data of internal voltage reference
2459 * @note On this STM32 series, calibration data of temperature sensor
2509 * If temperature sensor calibration values are available on
2510 * on this device (presence of macro __LL_ADC_CALC_TEMPERATURE()),
2522 …* On STM32H7, refer to device datasheet parameter "Avg_Slope…
2524 …* On STM32H7, refer to device datasheet parameter "V30" (cor…
2600 * (1) Available on devices with several ADC instances.
2631 * @note On this STM32 series, if ADC group injected is used, some
2635 * @note On this STM32 series, setting of this feature is conditioned to
2713 * @note On this STM32 series, setting of this feature is conditioned to
2845 * @note On this STM32 series, setting of this feature is conditioned to
2847 * ADC must be enabled, without calibration on going, without conversion
2848 * on going on group regular.
2892 /* Retrieve bits with position in register depending on parameter */ in LL_ADC_GetCalibrationOffsetFactor()
2908 * @note On this STM32 series, setting of this feature is conditioned to
2910 * ADC must be enabled, without calibration on going, without conversion
2911 * on going on group regular.
2983 * @note On this STM32 series, setting of this feature is conditioned to
2985 * ADC must be disabled or enabled without conversion on going
2986 * on either groups regular or injected.
3129 * 2. Later on, when conversion data is needed: poll for end of
3133 * - ADC low power mode "auto power-off" (feature available on
3143 * correspond to the current voltage level on the selected
3145 * @note On this STM32 series, setting of this feature is conditioned to
3147 * ADC must be disabled or enabled without conversion on going
3148 * on either groups regular or injected.
3185 * 2. Later on, when conversion data is needed: poll for end of
3189 * - ADC low power mode "auto power-off" (feature available on
3199 * correspond to the current voltage level on the selected
3262 * For Rest of STM32H7xxx This is applicable on all the ADCs instances.
3310 * (independently of channel mapped on ADC group regular
3315 * offset has to be left-aligned on bit 15 (handling maximum ADC resolution 16 bit),
3319 * @note If a channel is mapped on several offsets numbers, only the offset
3321 * @note On this STM32 series, setting of this feature is conditioned to
3323 * ADC must be disabled or enabled without conversion on going
3324 * on either groups regular or injected.
3325 * @note On STM32H7, some fast channels are available: fast analog inputs
3372 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
3373 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
3374 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
3401 * (independently of channel mapped on ADC group regular
3405 * the returned channel number is only partly formatted on definition
3414 * @note On STM32H7, some fast channels are available: fast analog inputs
3453 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
3454 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
3455 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
3473 * offset has to be left-aligned on bit 15 (handling maximum ADC resolution 16 bit),
3557 /* Function not available on this instance */ in LL_ADC_SetOffsetSignedSaturation()
3589 /* Function not available on this instance */ in LL_ADC_GetOffsetSignedSaturation()
3604 * @note On this STM32 series, setting of this feature is conditioned to
3606 * ADC must be disabled or enabled without conversion on going
3607 * on either groups regular or injected.
3668 * @note On this STM32 series, setting of this feature is conditioned to
3670 * ADC must be disabled or enabled without conversion on going
3671 * on either groups regular or injected.
3737 * @note On this STM32 series, setting of this feature is conditioned to
3739 * ADC must be disabled or enabled without conversion on going
3740 * on either groups regular or injected.
3817 * @note On this STM32 series, setting trigger source to external trigger
3819 * (default setting for compatibility with some ADC on other
3824 * depends on timers availability on the selected device.
3825 * @note On this STM32 series, setting of this feature is conditioned to
3827 * ADC must be disabled or enabled without conversion on going
3828 * on group regular.
3873 * depends on timers availability on the selected device.
3905 /* Value for shift of {0; 4; 8; 12} depending on value of bitfield */ in LL_ADC_REG_GetTriggerSource()
3936 * @note On this STM32 series, setting of this feature is conditioned to
3938 * ADC must be disabled or enabled without conversion on going
3939 * on group regular.
3974 * @note On this STM32 series, setting of this feature is conditioned to
3976 * ADC must be disabled or enabled without conversion on going
3977 * on group regular.
3991 /* Function not available on this instance */ in LL_ADC_REG_SetSamplingMode()
4021 * (channel 0 fixed on rank 0, channel 1 fixed on rank1, ...).
4028 * ADC conversion on only 1 channel.
4029 * @note On this STM32 series, setting of this feature is conditioned to
4031 * ADC must be disabled or enabled without conversion on going
4032 * on group regular.
4080 * (channel 0 fixed on rank 0, channel 1 fixed on rank1, ...).
4087 * ADC conversion on only 1 channel.
4121 * @note On this STM32 series, setting of this feature is conditioned to
4123 * ADC must be disabled or enabled without conversion on going
4124 * on group regular.
4169 * @brief Set ADC group regular sequence: channel on the selected
4174 * @note On this STM32 series, ADC group regular sequencer is
4178 * @note Depending on devices and packages, some channels may not be available.
4180 * @note On this STM32 series, to measure internal channels (VrefInt,
4184 * @note On this STM32 series, setting of this feature is conditioned to
4186 * ADC must be disabled or enabled without conversion on going
4187 * on group regular.
4249 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
4250 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
4251 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
4258 /* in register and register position depending on parameter "Rank". */ in LL_ADC_REG_SetSequencerRanks()
4269 * @brief Get ADC group regular sequence: channel on the selected
4271 * @note On this STM32 series, ADC group regular sequencer is
4275 * @note Depending on devices and packages, some channels may not be available.
4279 * the returned channel number is only partly formatted on definition
4349 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
4350 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
4351 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
4368 * @brief Set ADC continuous conversion mode on ADC group regular.
4375 * @note On this STM32 series, setting of this feature is conditioned to
4377 * ADC must be disabled or enabled without conversion on going
4378 * on group regular.
4392 * @brief Get ADC continuous conversion mode on ADC group regular.
4467 * @note On this STM32 series, setting of this feature is conditioned to
4469 * ADC must be disabled or enabled without conversion on going
4470 * on either groups regular or injected.
4562 * @note On this STM32 series, setting of this feature is conditioned to
4564 * ADC must be disabled or enabled without conversion on going
4565 * on group regular.
4604 * @note On this STM32 series, setting trigger source to external trigger
4606 * (default setting for compatibility with some ADC on other
4611 * depends on timers availability on the selected device.
4612 * @note On this STM32 series, setting of this feature is conditioned to
4615 * on going on either groups regular or injected.
4660 * depends on timers availability on the selected device.
4692 /* Value for shift of {0; 4; 8; 12} depending on value of bitfield */ in LL_ADC_INJ_GetTriggerSource()
4723 * @note On this STM32 series, setting of this feature is conditioned to
4726 * on going on either groups regular or injected.
4762 * ADC conversion on only 1 channel.
4763 * @note On this STM32 series, setting of this feature is conditioned to
4766 * on going on either groups regular or injected.
4788 * ADC conversion on only 1 channel.
4836 * @brief Set ADC group injected sequence: channel on the selected
4838 * @note Depending on devices and packages, some channels may not be available.
4840 * @note On this STM32 series, to measure internal channels (VrefInt,
4844 * @note On STM32H7, some fast channels are available: fast analog inputs
4846 * @note On this STM32 series, setting of this feature is conditioned to
4849 * on going on either groups regular or injected.
4887 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
4888 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
4889 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
4896 /* in register depending on parameter "Rank". */ in LL_ADC_INJ_SetSequencerRanks()
4905 * @brief Get ADC group injected sequence: channel on the selected
4907 * @note Depending on devices and packages, some channels may not be available.
4911 * the returned channel number is only partly formatted on definition
4957 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
4958 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
4959 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
4980 * 1 data register on ADC group regular, 4 data registers
4981 * on ADC group injected.
4987 * further action on ADC group injected conversion start or stop:
4992 * @note On this STM32 series, setting of this feature is conditioned to
4994 * ADC must be disabled or enabled without conversion on going
4995 * on either groups regular or injected.
5046 * @note This parameter can be modified only when no conversion is on going
5047 * on either groups regular or injected.
5050 * @note On this STM32 series, setting of this feature is conditioned to
5052 * ADC must be disabled or enabled without conversion on going
5053 * on either groups regular or injected.
5084 * @brief Set one context on ADC group injected that will be checked in
5100 * @note On this STM32 series, to measure internal channels (VrefInt,
5104 * @note On STM32H7, some fast channels are available: fast analog inputs
5106 * @note On this STM32 series, setting of this feature is conditioned to
5109 * on going on either groups regular or injected.
5180 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
5181 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
5182 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
5211 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
5212 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
5213 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
5242 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
5243 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
5244 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
5273 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
5274 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
5275 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
5289 /* in register depending on literal "LL_ADC_INJ_RANK_x". */ in LL_ADC_INJ_ConfigQueueContext()
5324 * @note On this device, sampling time is on channel scope: independently
5325 * of channel mapped on ADC group regular or injected.
5334 * On this STM32 series, ADC processing time is:
5343 * @note On this STM32 series, setting of this feature is conditioned to
5345 * ADC must be disabled or enabled without conversion on going
5346 * on either groups regular or injected.
5394 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
5395 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
5396 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
5412 /* in register and register position depending on parameter "Channel". */ in LL_ADC_SetChannelSamplingTime()
5425 * @note On this device, sampling time is on channel scope: independently
5426 * of channel mapped on ADC group regular or injected.
5428 * On this STM32 series, ADC processing time is:
5480 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
5481 * (2) On STM32H7, parameter available only on ADC instance: ADC2.\n
5482 …* (3) On STM32H7, fast channel (0.125 us for 14-bit resolution (ADC conversion rate up to …
5507 * @note Channel ending is on channel scope: independently of channel mapped
5508 * on ADC group regular or injected.
5519 * @note On STM32H7, some channels are internally fixed to single-ended inputs
5527 * @note On this STM32 series, setting of this feature is conditioned to
5598 * @note On STM32H7, some channels are internally fixed to single-ended inputs
5646 * on ADC groups regular and-or injected.
5652 * @note On this STM32 series, there are 2 kinds of analog watchdog
5660 * - channels monitored: flexible on channels monitored, selection is
5665 * - groups monitored: not selection possible (monitoring on both
5667 * Channels selected are monitored on groups regular and injected:
5673 * @note On this STM32 series, setting of this feature is conditioned to
5675 * ADC must be disabled or enabled without conversion on going
5676 * on either groups regular or injected.
5769 * (0) On STM32H7, parameter available only on analog watchdog number: AWD1.\n
5770 * (1) On STM32H7, parameter available only on ADC instance: ADC3.\n
5771 * (2) On STM32H7, parameter available only on ADC instance: ADC2.
5777 /* in register and register position depending on parameter "AWDy". */ in LL_ADC_SetAnalogWDMonitChannels()
5792 * the returned channel number is only partly formatted on definition
5803 * @note On this STM32 series, there are 2 kinds of analog watchdog
5811 * - channels monitored: flexible on channels monitored, selection is
5816 * - groups monitored: not selection possible (monitoring on both
5818 * Channels selected are monitored on groups regular and injected:
5824 * @note On this STM32 series, setting of this feature is conditioned to
5826 * ADC must be disabled or enabled without conversion on going
5827 * on either groups regular or injected.
5840 * (1) On this AWD number, monitored channel can be retrieved
5911 * (0) On STM32H7, parameter available only on analog watchdog number: AWD1.
5975 * @note On this STM32 series, there are 2 kinds of analog watchdog
5983 * - channels monitored: flexible on channels monitored, selection is
5988 * - groups monitored: not selection possible (monitoring on both
5990 * Channels selected are monitored on groups regular and injected:
5998 * on oversampling intermediate computation (after ratio, before shift
6001 * @note On this STM32 series, setting of this feature is conditioned to
6003 * ADC must be disabled or enabled without conversion on going
6004 * on either ADC groups regular or injected.
6028 /* position in register and register position depending on parameters */ in LL_ADC_SetAnalogWDThresholds()
6041 /* position in register and register position depending on parameters */ in LL_ADC_SetAnalogWDThresholds()
6053 /* position in register and register position depending on parameters */ in LL_ADC_SetAnalogWDThresholds()
6128 * @note On this STM32 series, there are 2 kinds of analog watchdog
6136 * - channels monitored: flexible on channels monitored, selection is
6141 * - groups monitored: not selection possible (monitoring on both
6143 * Channels selected are monitored on groups regular and injected:
6167 /* position in register and register position depending on parameter */ in LL_ADC_ConfigAnalogWDThresholds()
6197 * @note On this STM32 series, setting of this feature is conditioned to
6199 * ADC must be disabled or enabled without conversion on going
6200 * on either groups regular or injected.
6201 * Applicable on ADC3 of devices STM32H72xx and STM32H73xx.
6202 * @note On this STM32 series, this feature is only available on first
6231 * @note On this STM32 series, this feature is only available on first
6233 * Applicable on ADC3 of devices STM32H72xx and STM32H73xx.
6258 /* Function not available on this instance, return 0 */ in LL_ADC_GetAWDFilteringConfiguration()
6273 * (availability of ADC group injected depends on STM32 families).
6277 * the oversampling on ADC group regular is either
6280 * @note On this STM32 series, setting of this feature is conditioned to
6282 * ADC must be disabled or enabled without conversion on going
6283 * on either groups regular or injected.
6303 * (availability of ADC group injected depends on STM32 families).
6307 * the oversampling on ADC group regular is either
6328 * on the selected ADC group.
6334 * @note On this STM32 series, setting of this feature is conditioned to
6336 * ADC must be disabled or enabled without conversion on going
6337 * on group regular.
6338 * @note On this STM32 series, oversampling discontinuous mode
6340 * set on group regular only and in resumed mode.
6355 * on the selected ADC group.
6378 * @note On this STM32 series, setting of this feature is conditioned to
6380 * ADC must be disabled or enabled without conversion on going
6381 * on either groups regular or injected.
6495 * @note On this STM32 series, setting of this feature is conditioned to
6497 * ADC boost must be configured, without calibration on going, without conversion
6498 * on going on group regular.
6531 * @note On this STM32 series, setting of this feature is conditioned to
6533 * ADC boost must be configured, without calibration on going, without conversion
6534 * on going on group regular.
6555 * either master or slave depending on hardware.
6557 * @note On this STM32 series, setting of this feature is conditioned to
6586 * either master or slave depending on hardware.
6636 * @note On this STM32 series, setting of this feature is conditioned to
6639 * or enabled without conversion on going on group regular.
6699 * @note The sampling delay range depends on ADC resolution:
6704 * @note On this STM32 series, setting of this feature is conditioned to
6778 /** @defgroup ADC_LL_EF_Operation_ADC_Instance Operation on ADC hierarchical scope: ADC instance
6788 * @note On this STM32 series, setting of this feature is conditioned to
6811 * @note On this STM32 series, setting of this feature is conditioned to
6839 * @note On this STM32 series, after ADC internal voltage regulator enable,
6844 * @note On this STM32 series, setting of this feature is conditioned to
6863 * @note On this STM32 series, setting of this feature is conditioned to
6888 * @note On this STM32 series, after ADC enable, a delay for
6892 * @note On this STM32 series, flag LL_ADC_FLAG_ADRDY is raised when the ADC
6895 * @note On this STM32 series, setting of this feature is conditioned to
6914 * @note On this STM32 series, setting of this feature is conditioned to
6916 * ADC must be not disabled. Must be enabled without conversion on going
6917 * on either groups regular or injected.
6934 * @note On this STM32 series, flag LL_ADC_FLAG_ADRDY is raised when the ADC
6950 * @retval 0: no ADC disable command on going.
6960 * @note On this STM32 series, a minimum number of ADC clock cycles
6975 * @note On this STM32 series, setting of this feature is conditioned to
7015 /** @defgroup ADC_LL_EF_Operation_ADC_Group_Regular Operation on ADC hierarchical scope: group regu…
7021 * @note On this STM32 series, this function is relevant for both
7026 * will start at next trigger event (on the selected trigger edge)
7028 * @note On this STM32 series, setting of this feature is conditioned to
7030 * ADC must be enabled without conversion on going on group regular,
7031 * without conversion stop command on going on group regular,
7032 * without ADC disable command on going.
7049 * @note On this STM32 series, setting of this feature is conditioned to
7051 * ADC must be enabled with conversion on going on group regular,
7052 * without ADC disable command on going.
7071 * @retval 0: no conversion is on going on ADC group regular.
7082 * @retval 0: no command of conversion stop is on going on ADC group regular.
7210 /** @defgroup ADC_LL_EF_Operation_ADC_Group_Injected Operation on ADC hierarchical scope: group inj…
7216 * @note On this STM32 series, this function is relevant for both
7221 * will start at next trigger event (on the selected trigger edge)
7223 * @note On this STM32 series, setting of this feature is conditioned to
7225 * ADC must be enabled without conversion on going on group injected,
7226 * without conversion stop command on going on group injected,
7227 * without ADC disable command on going.
7244 * @note On this STM32 series, setting of this feature is conditioned to
7246 * ADC must be enabled with conversion on going on group injected,
7247 * without ADC disable command on going.
7266 * @retval 0: no conversion is on going on ADC group injected.
7277 * @retval 0: no command of conversion stop is on going on ADC group injected.
7455 * @note On this STM32 series, flag LL_ADC_FLAG_ADRDY is raised when the ADC
7590 * @note On this STM32 series, flag LL_ADC_FLAG_ADRDY is raised when the ADC
8373 /* (availability of ADC group injected depends on STM32 families) */