Lines Matching full:on
72 … compatibility with some ADC on other STM32 series
106 ADC_CHANNEL_ID_NUMBER_MASK with reduced range: on this STM32 series, ADC group regular sequencer,
113 /* Equivalent mask of ADC_CHANNEL_NUMBER_MASK aligned on register LSB (bit 0) */
170 /* on one of the common sampling time available. */
180 /* (feature of several watchdogs not available on all STM32 series)). */
184 /* selection on groups. */
252 Writing '0' has no effect on the bit value. */
264 …L1_ADDR ((uint16_t*) (0x0BF90710UL)) /* Address of parameter TS_CAL1: On this series,
267 …L2_ADDR ((uint16_t*) (0x0BF90742UL)) /* Address of parameter TS_CAL2: On this series,
293 * (shift mask on register position bit 0).
344 * @note These parameters have an impact on ADC scope: ADC instance.
353 * (setting possible with ADC enabled without conversion on going,
354 * ADC enabled with conversion on going, ...)
377 * @note These parameters have an impact on ADC scope: ADC group regular.
387 * (setting possible with ADC enabled without conversion on going,
388 * ADC enabled with conversion on going, ...)
399 … @note On this STM32 series, setting trigger source to external trigger also
401 … with some ADC on other STM32 series having this setting set by HW
420 … enabled (depending on the sequencer mode: scan length of 2 ranks or
426 …uint32_t ContinuousMode; /*!< Set ADC continuous conversion mode on ADC group regular…
591 (alignment on data register LSB bit 0)*/
593 (alignment on data register MSB bit 15)*/
672 #define LL_ADC_GROUP_REGULAR (0x00000001UL) /*!< ADC group regular (available on …
795 /** @defgroup ADC_LL_EC_REG_OVR_DATA_BEHAVIOR ADC group regular - Overrun behavior on conversion d…
824 … (equivalent to sequencer of 1 rank: ADC conversion on only 1 channel) */
846 #define LL_ADC_REG_SEQ_SCAN_DIR_FORWARD (0x00000000UL) /*!< On this STM32 series, parameter…
851 … sequencer). On some other STM32 series, this setting is not available
853 #define LL_ADC_REG_SEQ_SCAN_DIR_BACKWARD (ADC_CFGR1_SCANDIR) /*!< On this STM32 series, parameter…
1016 …GRP_REGULAR_CONTINUED (ADC_CFGR2_OVSE) /*!< ADC oversampling on conversions of
1106 … @ref __LL_ADC_CALC_TEMPERATURE(), due to issue on
1107 … calibration parameters. This value is coded on 16 bits
1108 … (to fit on signed word or double word) and corresponds
1117 * For details on delays values, refer to descriptions in source code
1136 /* - ADC conversion time: duration depending on ADC clock and ADC */
1166 /* Note: On this STM32 series, a minimum number of ADC clock cycles */
1385 * selected is available on the ADC instance selected.
1401 …* @retval Value "0" if the internal channel selected is not available on the ADC instance selected.
1402 * Value "1" if the internal channel selected is available on the ADC instance selected.
1471 * analog watchdog threshold high (on 8 bits):
1493 * analog watchdog threshold high (on 8 bits):
1545 * @note On devices with only 1 ADC common instance, parameter of this macro
1629 * @note This voltage depends on user board environment: voltage level
1631 * On devices with small package, the pin Vref+ is not present
1633 * @note On this STM32 series, calibration data of internal voltage reference
1683 * @note On this STM32 series, calibration data of temperature sensor
1737 * If temperature sensor calibration values are available on
1738 * on this device (presence of macro __LL_ADC_CALC_TEMPERATURE()),
1751 …* On this STM32 series, refer to device datasheet parameter …
1754 …* On this STM32 series, refer to datasheet parameter "V30" (…
1851 * @note On this STM32 series, setting of this feature is conditioned to
1924 * @note On this STM32 series, setting of this feature is conditioned to
1964 * @note On this STM32 series, setting of this feature is conditioned to
1992 * @note On this STM32 series, setting of this feature is conditioned to
2047 * @note On this STM32 series, setting of this feature is conditioned to
2049 * ADC must be enabled, without calibration on going, without conversion
2050 * on going on group regular.
2081 * @note On this STM32 series, setting of this feature is conditioned to
2083 * ADC must be disabled or enabled without conversion on going
2084 * on group regular.
2120 * @note On this STM32 series, setting of this feature is conditioned to
2122 * ADC must be disabled or enabled without conversion on going
2123 * on group regular.
2174 * 2. Later on, when conversion data is needed: poll for end of
2182 * correspond to the current voltage level on the selected
2184 * @note On this STM32 series, setting of this feature is conditioned to
2186 * ADC must be disabled or enabled without conversion on going
2187 * on group regular.
2223 * 2. Later on, when conversion data is needed: poll for end of
2231 * correspond to the current voltage level on the selected
2256 * @note On this STM32 series, setting of this feature is conditioned to
2292 * @note On this STM32 series, setting of this feature is conditioned to
2334 * @note On this STM32 series, setting of this feature is conditioned to
2365 * @note On this STM32 series, sampling time scope is on ADC instance:
2367 * (on some other STM32 series, sampling time is channel wise)
2376 * On this STM32 series, ADC processing time is:
2385 * @note On this STM32 series, setting of this feature is conditioned to
2387 * ADC must be disabled or enabled without conversion on going
2388 * on group regular.
2417 * @note On this STM32 series, sampling time scope is on ADC instance:
2419 * (on some other STM32 series, sampling time is channel wise)
2457 * @note On this STM32 series, setting trigger source to external trigger
2459 * (default setting for compatibility with some ADC on other
2463 * @note On this STM32 series, ADC trigger frequency mode must be set
2468 * depends on timers availability on the selected device.
2469 * @note On this STM32 series, setting of this feature is conditioned to
2471 * ADC must be disabled or enabled without conversion on going
2472 * on group regular.
2501 * depends on timers availability on the selected device.
2517 /* Value for shift of {0; 4; 8; 12} depending on value of bitfield */ in LL_ADC_REG_GetTriggerSource()
2548 * @note On this STM32 series, setting of this feature is conditioned to
2550 * ADC must be disabled or enabled without conversion on going
2551 * on group regular.
2582 * @note On this STM32 series, ADC group regular sequencer both modes
2595 * @note On this STM32 series, setting of this feature is conditioned to
2597 * ADC must be disabled or enabled without conversion on going
2598 * on group regular.
2613 * @note On this STM32 series, ADC group regular sequencer both modes
2658 * (channel 0 fixed on rank 0, channel 1 fixed on rank1, ...).
2666 * @note On this STM32 series, ADC group regular sequencer both modes
2671 * ADC conversion on only 1 channel.
2672 * @note On this STM32 series, setting of this feature is conditioned to
2674 * ADC must be disabled or enabled without conversion on going
2675 * on group regular.
2722 * (channel 0 fixed on rank 0, channel 1 fixed on rank1, ...).
2730 * @note On this STM32 series, ADC group regular sequencer both modes
2735 * ADC conversion on only 1 channel.
2781 * @note On this STM32 series, parameter relevant only is sequencer is set
2784 * @note On some other STM32 series, this setting is not available and
2786 * @note On this STM32 series, setting of this feature is conditioned to
2788 * ADC must be disabled or enabled without conversion on going
2789 * on group regular.
2804 * @note On this STM32 series, parameter relevant only is sequencer is set
2807 * @note On some other STM32 series, this setting is not available and
2826 * @note On this STM32 series, setting of this feature is conditioned to
2828 * ADC must be disabled or enabled without conversion on going
2829 * on group regular.
2858 * @brief Set ADC group regular sequence: channel on the selected
2863 * @note On this STM32 series, ADC group regular sequencer is
2867 * @note Depending on devices and packages, some channels may not be available.
2869 * @note On this STM32 series, to measure internal channels (VrefInt,
2873 * @note On this STM32 series, setting of this feature is conditioned to
2875 * ADC must be disabled or enabled without conversion on going
2876 * on group regular.
2918 /* in register depending on parameter "Rank". */ in LL_ADC_REG_SetSequencerRanks()
2928 * @brief Get ADC group regular sequence: channel on the selected
2930 * @note On this STM32 series, ADC group regular sequencer is
2934 * @note Depending on devices and packages, some channels may not be available.
2938 * the returned channel number is only partly formatted on definition
2998 * @brief Set ADC group regular sequence: channel on rank corresponding to
3003 * (channel 0 fixed on rank 0, channel 1 fixed on rank1, ...).
3006 * @note On this STM32 series, ADC group regular sequencer both modes
3013 * @note Depending on devices and packages, some channels may not be available.
3015 * @note On this STM32 series, to measure internal channels (VrefInt,
3019 * @note On this STM32 series, setting of this feature is conditioned to
3021 * ADC must be disabled or enabled without conversion on going
3022 * on group regular.
3073 * @brief Add channel to ADC group regular sequence: channel on rank corresponding to
3078 * (channel 0 fixed on rank 0, channel 1 fixed on rank1, ...).
3081 * @note On this STM32 series, ADC group regular sequencer both modes
3088 * @note Depending on devices and packages, some channels may not be available.
3090 * @note On this STM32 series, to measure internal channels (VrefInt,
3094 * @note On this STM32 series, setting of this feature is conditioned to
3096 * ADC must be disabled or enabled without conversion on going
3097 * on group regular.
3148 * @brief Remove channel to ADC group regular sequence: channel on rank corresponding to
3153 * (channel 0 fixed on rank 0, channel 1 fixed on rank1, ...).
3156 * @note On this STM32 series, ADC group regular sequencer both modes
3163 * @note Depending on devices and packages, some channels may not be available.
3165 * @note On this STM32 series, to measure internal channels (VrefInt,
3169 * @note On this STM32 series, setting of this feature is conditioned to
3171 * ADC must be disabled or enabled without conversion on going
3172 * on group regular.
3223 * @brief Get ADC group regular sequence: channel on rank corresponding to
3228 * (channel 0 fixed on rank 0, channel 1 fixed on rank1, ...).
3229 * @note On this STM32 series, ADC group regular sequencer both modes
3236 * @note Depending on devices and packages, some channels may not be available.
3238 * @note On this STM32 series, to measure internal channels (VrefInt,
3242 * @note On this STM32 series, setting of this feature is conditioned to
3244 * ADC must be disabled or enabled without conversion on going
3245 * on group regular.
3307 * @brief Set ADC continuous conversion mode on ADC group regular.
3314 * @note On this STM32 series, setting of this feature is conditioned to
3316 * ADC must be disabled or enabled without conversion on going
3317 * on group regular.
3331 * @brief Get ADC continuous conversion mode on ADC group regular.
3367 * @note On this STM32 series, setting of this feature is conditioned to
3369 * ADC must be disabled or enabled without conversion on going
3370 * on group regular.
3427 * @note On this STM32 series, setting of this feature is conditioned to
3429 * ADC must be disabled or enabled without conversion on going
3430 * on group regular.
3468 * @note On this device, sampling time is on channel scope: independently
3469 * of channel mapped on ADC group regular or injected.
3484 * @note On this STM32 series, setting of this feature is conditioned to
3486 * ADC must be disabled or enabled without conversion on going
3487 * on group regular.
3544 * @note On this device, sampling time is on channel scope: independently
3545 * of channel mapped on ADC group regular or injected.
3602 /* Select sampling time bitfield depending on sampling time bit value 0 or 1. */ in LL_ADC_GetChannelSamplingTime()
3618 * on ADC group regular.
3624 * @note On this STM32 series, setting of this feature is conditioned to
3626 * ADC must be disabled or enabled without conversion on going
3627 * on group regular.
3661 /* in register and register position depending on parameter "AWDy". */ in LL_ADC_SetAnalogWDMonitChannels()
3685 * the returned channel number is only partly formatted on definition
3696 * @note On this STM32 series, setting of this feature is conditioned to
3698 * ADC must be disabled or enabled without conversion on going
3699 * on group regular.
3711 * (1) On this AWD number, monitored channel can be retrieved
3799 * impacted: the comparison of analog watchdog thresholds is done on
3804 * on 12 bits (ratio 16 and shift 4, or ratio 32 and shift 5, ...):
3807 * on 14 bits (ratio 16 and shift 2, or ratio 32 and shift 3, ...):
3810 * on 16 bits (ratio 16 and shift none, or ratio 32 and shift 1, ...):
3812 * @note On this STM32 series, setting of this feature is conditioned to
3814 * ADC must be disabled or enabled without conversion on going
3815 * on group regular.
3835 /* position in register and register position depending on parameter */ in LL_ADC_ConfigAnalogWDThresholds()
3860 * impacted: the comparison of analog watchdog thresholds is done on
3865 * on 12 bits (ratio 16 and shift 4, or ratio 32 and shift 5, ...):
3868 * on 14 bits (ratio 16 and shift 2, or ratio 32 and shift 3, ...):
3871 * on 16 bits (ratio 16 and shift none, or ratio 32 and shift 1, ...):
3873 * @note On this STM32 series, setting of this feature is not conditioned to
3875 * ADC can be disabled, enabled with or without conversion on going
3876 * on ADC group regular.
3898 /* position in register and register position depending on parameters */ in LL_ADC_SetAnalogWDThresholds()
3945 /* position in register and register position depending on parameters */ in LL_ADC_GetAnalogWDThresholds()
3971 * @note On this STM32 series, setting of this feature is conditioned to
4001 * on the selected ADC group.
4007 * @note On this STM32 series, setting of this feature is conditioned to
4009 * ADC must be disabled or enabled without conversion on going
4010 * on group regular.
4025 * on the selected ADC group.
4047 * @note On this STM32 series, setting of this feature is conditioned to
4122 /** @defgroup ADC_LL_EF_Operation_ADC_Instance Operation on ADC hierarchical scope: ADC instance
4128 * @note On this STM32 series, there are three possibilities to enable
4136 * @note On this STM32 series, after ADC internal voltage regulator enable,
4141 * @note On this STM32 series, setting of this feature is conditioned to
4160 * @note On this STM32 series, setting of this feature is conditioned to
4185 * @note On this STM32 series, after ADC enable, a delay for
4189 * @note On this STM32 series, flag LL_ADC_FLAG_ADRDY is raised when the ADC
4192 * @note On this STM32 series, setting of this feature is conditioned to
4211 * @note On this STM32 series, setting of this feature is conditioned to
4213 * ADC must be not disabled. Must be enabled without conversion on going
4214 * on group regular.
4231 * @note On this STM32 series, flag LL_ADC_FLAG_ADRDY is raised when the ADC
4247 * @retval 0: no ADC disable command on going.
4257 * @note On this STM32 series, a minimum number of ADC clock cycles
4261 * On this STM32 series, ADC DMA transfer request should be disabled
4275 * @note On this STM32 series, setting of this feature is conditioned to
4307 /** @defgroup ADC_LL_EF_Operation_ADC_Group_Regular Operation on ADC hierarchical scope: group regu…
4313 * @note On this STM32 series, this function is relevant for both
4318 * will start at next trigger event (on the selected trigger edge)
4320 * @note On this STM32 series, setting of this feature is conditioned to
4322 * ADC must be enabled without conversion on going on group regular,
4323 * without conversion stop command on going on group regular,
4324 * without ADC disable command on going.
4341 * @note On this STM32 series, setting of this feature is conditioned to
4343 * ADC must be enabled (potentially with conversion on going on group regular),
4344 * without ADC disable command on going.
4363 * @retval 0: no conversion is on going on ADC group regular.
4374 * @retval 0: no command of conversion stop is on going on ADC group regular.
4465 * @note On this STM32 series, flag LL_ADC_FLAG_ADRDY is raised when the ADC
4578 * @note On this STM32 series, flag LL_ADC_FLAG_ADRDY is raised when the ADC